Page 1: Lcd Monitor
SyncMaster 320MP-2 LCD Monitor User Manual...
Page 2: Safety Instructions
Safety Instructions Notational Note These safety instructions must be followed to ensure your safety and prevent property damage. Make sure to read the instructions carefully and use the product in the correct manner. Warning / Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment.
Page 3: Installation
• Installation Be sure to contact an authorized Service Center when installing your monitor in a location with heavy dust, high or low temperatures, high humidity, and exposed to chemical substances and where it operates for 24 hours such as at airports, train stations etc.
Page 4 10 cm from the wall. • Ensure that the packaging vinyl is kept away from children. • If the height of your monitor is adjustable, do not place any object or part of your body on the stand when lowering it. • Clean When cleaning the monitor case or the surface of the TFT-LCD screen, wipe with a slightly moistened, soft fabric.
Page 5 When cleaning the product, make sure to disconnect the power cord. • When cleaning the product, disconnect the power cord and clean it softly with a dry cloth. • Since the product housing is easily scratched, make sure to use the specified cloth only.
Page 6 Do not try to move the monitor by pulling only the wire or the signal cable. • Otherwise, it may fall and result in electric shock, damage to the product or fire due to damage to the cable. Do not lift or move the product back and forwards or right and left while only holding the power cord or signal cables.
Page 7 Take a rest for at least five (5) minutes after using the monitor for one (1) hour. This reduces the weariness of your eyes. Do not install it in an unstable location such as an unstable rack or uneven surface or a location exposed to vibrations.
Page 8 Do not place the product in a location exposed to direct sunlight or near any heat such as a fire or heater. • This may reduce the lifetime of the product, and may result in fire. Do not drop any objects onto the product or cause any impact to the product.
Page 9: Package Contents
Introduction Package Contents Note Please make sure the following items are included with your LCD Display. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Note This stand is not for the Floor Standing Type. Unpacking Manuals Quick Setup Guide...
Page 10 Others Sold separately DVI Cable TV tuner box BNC Cable Note • You can purchase and connect a separate network box or TV tuner box. For information on how to use these, refer to their respective user manuals. • You can only connect one external box. Your LCD Display Front (Not available in all loca-...
Page 11 MENU button [MENU] Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu or return to the previous menu. Navigate buttons (Up-Down buttons) Moves from one menu item to another vertically or adjusts selected menu values. Adjust buttons (Left-Right buttons) / Volume buttons Moves from one menu item to another horizontally or adjusts selected menu val- ues.
Page 12 POWER S/W ON [ │ ] / OFF [O] Switches the LCD Display On/Off. POWER IN The power cord plugs into the LCD Display and the wall plug. RS232C OUT/IN (RS232C Serial PORT) MDC(Multiple Display Control) Program Port DVI / PC / HDMI IN [DVI/PC/HDMI AUDIO IN] (PC/DVI/HDMI Audio Connection Terminal (Input)) DVI / PC / HDMI IN [HDMI]...
Page 13 Otherwise, this may result in damage to the prod- uct. AV IN [VIDEO] (VIDEO Connection Termi- nal) Connect the [ VIDEO ] terminal of your monitor to the video output terminal of the external device using a VIDEO cable. AV AUDIO IN [L-AUDIO-R](LCD Display...
Page 14: Remote Control
The location of the Kensington Lock may be dif- ferent depending on its model. Using the Anti-Theft Kensington Lock Insert the locking device into the Kensington slot on the Monitor and turn it in the locking direction Connect the Kensington Lock cable.
Page 15 POWER 3. Number Buttons POWER Number Buttons button + VOL - MUTE TV/DTV MENU INFO COLOR BUTTONS TTX/MIX STILL AUTO S.MODE LOCK SOURCE ENTER/PRE-CH CH/P D.MENU GUIDE RETURN Up-Down Left-Right buttons EXIT MagicInfo P.MODE DUAL/MTS SWAP Turns the product On. Turns the product Off.
Page 16 Press the button to change the input signal SOURCE. Changing the SOURCE is only allowed for external devices that are connected to the monitor at the time. This button is used to return to the immediately previous channel. In TV mode, selects TV channels.
Page 17 24. Up-Down Left-Right but- tons EXIT 27.MagicInfo 28. P.MODE DUAL/MTS 30. PIP 31.SWAP Mechanical Layout Mechanical Layout Moves from one menu item to another horizontally, vertically or adjusts selected menu values. Exits from the menu screen. Selects SRS TruSurround XT mode. MagicInfo Quick Launch Button.
Page 18: Installation Vesa Bracket
• At least 2 persons are needed in order to move the LCD Display. • SAMSUNG is not responsible for any product damage or any injury caused by installation at customer's discretion. Dimensions Notice For securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12 mm length.
Page 19: Wall Bracket Installation
• Contact a technician for installing the wall bracket. • SAMSUNG Electronics is not responsible for any damages to the product or harm to customers when the installation is done by the customer. • This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood.
Page 20: To Mount The Product On The Wall Bracket
Before drilling into the wall, check if the length between the two locking holes at the back of the product is correct. If the length is too short or long, loosen all or some of the 4screws on the wall bracket to adjust the length.
Page 21 Insert the screw B into the plastic hanger. Notice • Mount the product on the wall bracket and make sure it is properly fixed to the left and right plastic hangers. • Be careful when installing the product on the bracket as fingers can be caught in the holes. •...
Page 22: Wall Bracket Angle Adjustment
Wall Bracket Angle Adjustment Adjust the bracket angle to -2° before installing it on the wall. Fix the product to the wall bracket. Hold the product at the top in the center and pull it forward (direction of the arrow) to adjust the angle.
Page 23: Connecting A Computer
Connections Connecting a Computer Using a Power cord with Earth • In the event of failure, the earth lead may cause electric shock. Make sure to wire the earth lead in correctly, before connecting the AC power. When un- wiring the earth lead, make sure to disconnect the AC power in advance. Note AV input devices such as DVD players, VCRs or camcorders as well as your computer can be connected to the LCD Display.
Page 24: Connecting To Other Devices
Turn on both your computer and the LCD Display. • The DVI cable is optional. • Contact a local SAMSUNG Electronics Service Center to buy optional items. Connecting to Other devices Using a Power cord with Earth • In the event of failure, the earth lead may cause electric shock. Make sure to wire the earth lead in correctly, before connecting the AC power.
Page 25: Connecting To A Camcorder
Connect the port of the DVD, VCR (DVD / DTV Set-Top Box) to the [R-AUDIO-L] port of the LCD Display. Then, start the DVD, VCR or Camcorders with a DVD disc or tape inserted. Select AV using the SOURCE . Note The LCD Display has AV connection terminals to connect AV input devices like DVDs, VCRs or Camcorders.
Page 26: Connecting A Dtv Set Top Box
Connect a set of audio cables between the AV AUDIO IN [L-AUDIO-R] on the LCD Display and the AUDIO OUT jacks on the DVD player. Connect a Component cable between the BNC/COMPONENT IN- P Display and the P Note • Select Component for the connection to a DVD player using the SOURCE button on the front of the LCD Display or on the remote control.
Page 27: Connecting Using A Dvi To Hdmi Cable
Note • For an explanation of Component video, see your Set Top Box owner's manual. Connecting Using a HDMI Cable Note • Input devices such as digital DVD are connected to the HDMI terminal of the LCD Display using the HDMI cable. •...
Page 28 Connections Note • Connect a set of audio cables between the AUX L, R jacks on the AUDIO SYSTEM and AUDIO OUT [L-AUDIO-R] on LCD Display.
Page 29: Using The Software
Monitor Driver Note When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have.
Page 30: Installing The Monitor Driver (Manual)
Note This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ Installing the Monitor Driver (Manual) ® Microsoft Windows Vista™‚ Operating System Insert your Manual CD into your CD-ROM drive.
Page 31 Note This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage. Click "Update Driver..." in the "Driver" tab. Check the "Browse my computer for driver software" checkbox and click "Let me pick from a list of device drivers on my computer".
Page 32 Select the model that matches your monitor from the list of monitor models on the screen, and click "Next". 10. Click "Close" → "Close" → "OK" → "OK" on the following screens displayed in sequence. ® ® Microsoft Windows XP Operating System...
Page 33 Click "Start" → "Control Panel" then click the "Appearance and Themes" icon. Click "Display" icon and choose the "Settings" tab then click "Advanced...". Click the "Properties" button on the "Monitor" tab and select "Driver" tab. Click "Update Driver..." and select "Install from a list or..." then click "Next" button.
Page 34 Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button. If you can see following message window, then click the "Continue Anyway" button. Then click "OK" button. Note This monitor driver is under certifying MS logo, and this installation doesn't damage your system.
Page 35 Select the "Settings" tab and click "Advanced Properties" button. Choose "Monitor". Case1 : If the "Properties" button is inactive, it means your monitor is properly configured. Please stop installation Case2 : If the "Properties" button is active, click the "Properties" button then follow next steps continually.
Page 36 Click the "Have Disk" button. Specify A:\(D:\driver) then click "OK" button. 10. Select "Show all devices" and choose the monitor that corresponds to the one you connected to your computer and click "OK". 11. Continue choosing "Close" button and "OK" button until you close the Display Properties dia- logue box.
Page 37: Main Screen
Therefore, a serial cable should be connected between the serial port on a PC and the serial port on a display. Main Screen Click Start > Program > Samsung > MDC System to start the program. Select a set to see the volume of the selected set within the slider.
Page 38: Port Selection
Main Icons Remocon Safety Lock Port Selection 1. Use the main icons to switch into each screen. 2. Allows you to enable or disable the remote control signal receiving function of the display unit. 3. Set the Safety Lock function. When setting the Lock function, you can only operate power and lock buttons on the remote control and set.
Page 39: Power Control
1. The Multiple Display Control is originally set to COM1. 2. If any port other than COM1 is used, COM1 through COM4 can be selected in the Port Selection Menu. 3. If the exact port name that is connected to the LCD Display using a serial cable is not selected, communication will be unavailable.
Page 40 Info Grid shows some basic information necessary to Power Control. (Power Status) 2) Input 3) Image Size 4) On Timer 5) Off Timer 2. Use the Select All button or Check Box to choose a display to control. Power Control allows controlling some of the functions of the selected display. 1) Power On/Off...
Page 41: Input Source
- Turns the power of the selected display On/Off. 2) Volume - Controls the volume level of the selected display. It receives the volume value of the selected display from the sets and displays it in the slider. (When you cancel the selection or choose Select All, the value returns to the default value 10) (Mute On/Off) - Turns on/off the Mute function of the selected display.
Page 42: Image Size
Info Grid shows some basic information necessary to Input Source Control. - Changes the Input Source of the selected display to PC. - Changes the Input Source of the selected display to BNC. - Changes the Input Source of the selected display to DVI. - Changes the Input Source of the selected display to TV.
Page 43 Info Grid shows some basic information necessary to Image Size Control. ( Power Status) - Shows the power status of the current display. 2) Image Size - Shows the current Image Size of the display in use. 3) Input - Shows the current Input Source of the display in use. 4) Info Grid displays only the displays whose Input Source is PC, BNC, DVI.
Page 44 Info Grid shows some basic information necessary to Image Size Control. 1) Click the Video Source tab to adjust Image Size for TV, AV, S-Video, Component, DVI(HDCP), HDMI, DTV. Click Select All or use Check Box to select a display to control. 2) Info Grid displays only the display having TV, AV, S-Video, Component or DVI(HDCP) as input source.
Page 45: Pip Size
Info Grid shows some basic information necessary to Time Control. 1) Current Time - Set the current time for the selected display (PC Time). - To change the current time, first change the PC Time. 2) On Time Setup - Set the Hour, Minute, AM/PM of On Time Setup, Status, Source, Volume of the selected display. 3) Off Time Setup - Set the Hour, Minute, and AM/PM, Status for Off Time Setup of the selected display.
Page 46: Pip Source
Info Grid shows some basic information necessary to PIP Size Control. 1) PIP Size - Shows the current PIP Size of the display in use. 2) OFF - Turns off the PIP of the selected display. 3) Large - Turns on the PIP of the selected display and changes the size to Large. 4) Small - Turns on the PIP of the selected display and changes the size to Small.
Page 47 Info Grid shows some basic information necessary to PIP Source Control. 1) PIP Source - PIP Source can be controlled with turning on the LCD Display power. 2) PC - Changes the source of the PIP of the selected display to PC. 3) BNC - Changes the source of the PIP of the selected display to BNC.
Page 48: Picture Pc
Info Grid shows some basic information necessary to Settings Control. When each function is selected, the set value of the selected function is displayed in the slide.When selected, each function fetches the value for the set and displays it on the slide bar. When "Select All" is chosen, the default value is displayed.
Page 49 1. Click Settings of the main icons and the Settings Control screen appears. Info Grid shows some basic information necessary to Settings Control. When each function is selected, the set value of the selected function is displayed in the slide. When selected, each function fetches the value for the set and displays it on the slide bar.
Page 50: Image Lock
Settings Audio 1. Click Settings of the main icons and the Settings Control screen appears. Info Grid shows some basic information necessary to Settings Control. When each function is selected, the set value of the selected function is displayed in the slide. When selected, each function fetches the value for the set and displays it on the slide bar.
Page 51: Maintenance
Info Grid shows some basic information necessary to Settings Control. 1) Image Lock - Available only for PC, BNC. 2) Coarse - Adjusts Coarse of the selected display. 3) Fine - Adjusts Fine of the selected display. 4) Position - Adjusts Position of the selected display. 5) Auto Adjustment - Self-Adjust to the incoming PC signal.
Page 52 An "Info Grid" showing several basic data items appears. 1) Maintenance - Allows the Maintenance Control function for all input sources. 2) Auto Lamp Control - Automatically adjusts the backlight of the selected display at a specified time. The Manual Lamp Control automatically turns off if you adjust using the Auto Lamp Control. 3) Manual Lamp Control - Allows you to adjust the backlight of the selected display regardless of the time.
Page 53: Video Wall
- The Safety Screen function is used to prevent afterimages from occurring when a still screen is displayed on the monitor for a long time. The Interval item is used to set the repetition cycle in hour units and the Time item is used to set the time when the Safety Screen function must be performed.
Page 54: Troubleshooting
Select a display from Display Selection. The place will be set up by pressing a number in the selected mode. The MDC program supplied by Samsung supports up to 5x5 LCD Displayes. 3) On / Off - Turns on/off the Video Wall function of the selected display.
Page 55: Settings Value Display In Multiple Display Mode
- Check the displays to see if any of the other displays connected have the same ID. If more than one displays have the same ID, those displays are not properly detected by the program due to data conflict. - Check if the Display Set ID is a number between 0 and 25. (Adjust using the Display menu) Note : A Display Set ID must be a value between 0 and 25 .
Page 56: Adjusting The Lcd Display
Adjusting the LCD Display Input Available Modes • PC / BNC / DVI • • HDMI • Component Note • The TV menu is available when a TV tuner box is installed. • The MagicInfo menu is available when a network box is installed. Source List MENU →...
Page 57: Picture [Pc / Bnc / Dvi Mode]
BNC mode is not supported if the component cable is connected. To use BNC mode, remove the component cable and connect the BNC cable. Component Component mode is not supported if the BNC cable is connected. To use Component mode, remove the BNC cable and connect the Component cable.
Page 58 • The MagicInfo menu is available when a network box is installed. MagicBright MENU → → ENTER → [Picture] → ENTER →[MagicBright] → MagicBright is a feature providing the optimum viewing environment depending on the contents of the image you are watching. Currently four different modes are available: Entertain, Internet, Text and Custom.
Page 59 Adjusts the Contrast. Brightness MENU → → ENTER → [Picture] → ness] → , → ENTER Adjusts the Brightness. Sharpness MENU → → ENTER → [Picture] → [Sharpness] → , → ENTER Adjusts the Sharpness. Color Tone MENU → → ENTER → [Picture] → The color tones can be changed.
Page 60 Note If you adjust the picture by using the Color Control function, Color Tone will turn to the Custom mode. MENU → → ENTER → [Picture] → [Red] → , → ENTER Green MENU → → ENTER → [Picture] → → → →...
Page 61: Auto Adjustment
Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the center using the horizontal control menu. Fine MENU → → ENTER → [Picture] → → → → → ENTER → [Image Lock] → → ENTER →...
Page 62 Signal Balance MENU → → ENTER → [Picture] → ance] → ENTER → [Signal Balance] → Selects either On or Off with the signal control. Signal Control MENU → → ENTER → [Picture] → → ENTER → [Signal Control] ance] → R-Gain MENU →...
Page 63 B-Offset MENU → → ENTER → [Picture]→ → → → ance] → → ENTER → [Signal Control] → → → → → , → ENTER Size MENU → → ENTER → [Picture] → → ENTER The Size can be switched. 16:9 Dynamic Contrast MENU →...
Page 64: Picture [ Av / Hdmi / Component Mode]
Picture [ AV / HDMI / Component Mode] Available Modes • PC / BNC / DVI • • HDMI • Component Note • The TV menu is available when a TV tuner box is installed. • The MagicInfo menu is available when a network box is installed. Mode MENU →...
Page 65 Adjusts the Contrast. Brightness MENU → → ENTER → [Picture] → ness] → , → ENTER Adjusts the Brightness. Sharpness MENU → → ENTER → [Picture] → → ENTER [Sharpness] → , Adjusts the picture Sharpness. Color MENU → → ENTER → [Picture] → [Color] →...
Page 66: Color Temp
The color tones can be changed. The individual Color components are also user adjustable. Cool2 Cool1 Normal Warm1 Warm2 Note If you set the Color Tone to Cool2, Cool1, Normal, Warm1, or Warm2, the Color Temp function is disabled. Color Temp. MENU →...
Page 67: Film Mode
Note Certain external devices may feed the display an out of spec signal that may cause cutoff even when using the Just Scan feature. ZOOM1, ZOOM2 will be unavailabel in HDMI mode. Digital NR (Digital Noise Reduction) MENU → → ENTER → [Picture] → →...
Page 68 → ENTER → Dynamic Contrast automatically detects the distribution of the visual signal and adjusts to create an optimum contrast. Sound Available Modes • PC / BNC / DVI • • HDMI • Component Note • The TV menu is available when a TV tuner box is installed. •...
Page 69: Auto Volume
Selects Music when watching music videos or concerts. Movie Selects Movie when viewing movies. Speech Selects Speech when watching a show that is mostly dialogue (i.e., news). Custom Selects Custom if you want to adjust the settings according to your personal preferences. Custom The sound settings can be adjusted to suit your personal preferences.
Page 70 Reduces the difference in volume control between broadcasters. SRS TS XT MENU → → ENTER → [Sound] → → ENTER SRS TS XT is a patented SRS technology that solves the problem of playing 5.1 multichannel content over two speakers. TruSurround delivers a compelling, virtual surround sound experience through any two-speaker playback system, including internal television speakers.
Page 71: Clock Set
Note • The TV menu is available when a TV tuner box is installed. • The MagicInfo menu is available when a network box is installed. Language MENU → → → You can choose one of 13 languages. Note The language chosen affects only the language of the OSD. It has no effect on any software running on the computer.
Page 72: Off Timer
Turns the LCD Display off automatically at certain times. On Timer MENU → → → [On Timer] → Turns the LCD Display on automatically at a preset time. Controls the mode and the volume level at the time the LCD Display turns on automatically. Off Timer MENU →...
Page 73: Menu Transparency
Menu Transparency MENU → → → → ENTER Change the transparency of the background of the OSD. High Medium Opaque Safety Lock PIN MENU → → → [0~9] → [0~9] → [0~9] → [0~9] The password can be changed. Energy Saving MENU →...
Page 74: Hdmi Black Level
HDMI Black Level MENU → → → Level ] → , → ENTER When a DVD or set-top box is connected to your TV via HDMI, it may cause a degradation in the screen quality, such as an increase in the black level, a low contrast, or discoloration, etc., depending on the external device connected.
Page 75 Format MENU → → → Wall ] → → ENTER → [Format] → The Format can be selected to see a divided screen. Full Provides a full screen without any margins. Natural Displays a natural image with the original aspect ratio intact. Horizontal MENU →...
Page 76: Screen Divider
Screen Divider MENU → → → Wall ] → → → The screen can be divided into several images. A number of screens can be selected with a different layout when dividing. • Select a mode in Screen Divider. • Select a display in Display Selection.
Page 77 Horizontal Dot MENU → → → [Safety Screen] → ENTER → [Pixel Shift] → → ENTER → [Horizontal Dot] → , → ENTER Sets how many pixels the screen moves horizontally. Five adjustment levels: 0, 1, 2, 3, and 4. Vertical Line MENU →...
Page 78 You can set the timer for Screen Burn Protection. If you start the operation to erase any residual image, the operation will be performed for the set period of time and then automatically finish. Mode MENU → → → [Safety Screen] → →...
Page 79 Time MENU → → → [Safety Screen] → → ENTER → [Timer] → → → → ENTER → [Time] → , → ENTER Within the set period of time specify a time for execution. • Mode-Scroll : 1~5 sec • Mode-Bar, Eraser : 10~50 sec Scroll MENU →...
Page 80 Eraser MENU → → → [Safety Screen] → → This function prevents after-images on the screen by moving a rectangular pattern. Resolution Select MENU → → → → ENTER → [Setup → → → → → → → → → ENTER → [Resolution Select ] →...
Page 81: Side Gray
Adjusts the Power On time for the screen. Caution: Set the Power On time to be longer to avoid overvoltage. Side Gray MENU → → → → ENTER → [Side Gray] → Select the brightness of the grey for the screen background. Light Dark Reset...
Page 82 Note The Reset function is not available when Video Wall is On. Color Reset MENU → → → → ENTER → [Reset ] → OSD Rotation MENU → → → → ENTER → [OSD Rotation ] → → → , →...
Page 83: Multi Control
• HDMI • Component Multi Control Assigns an individual ID to the SET. MENU → → → • ID Setup Assigns distinctive IDs to the SET. • ID Input Use to select the transmitter functions of the individual SET. Only a SET where the ID corresponds to the transmitter setting becomes activated.
Page 84: Troubleshooting
Troubleshooting Self-Test Feature Check Note Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself. Self-Test Feature Check Turn off both your computer and the LCD Display. Unplug the video cable from the back of the computer. Turn on the LCD Display.
Page 85: Symptoms And Recommended Actions
• Do not use benzene, thinner or other flammable substan- ces, or a wet cloth. • We recommend that a SAMSUNG cleansing agent is used to prevent damage to the screen. • Never use acetone, benzene or thinner. (They may cause flaws or deformation of the screen sur- face.)
Page 86: Problems Related To The Screen
Check if the signal cable between the computer and the LCD Display is securely connected. (Refer to Connecting a Computer) Problems related to the Screen Note Problems related to the LCD Display screen and their solutions are listed. The screen is blank and the power indicator is off. Ensure that the power cord is firmly connected and the LCD Display is on.
Page 87: Problems Related To Audio
Adjust color using Custom under OSD Color Adjustment menu. The color image is distorted by dark shadows. Adjust color using Custom under OSD Color Adjustment menu. The color white is poor. Adjust color using Custom under OSD Color Adjustment menu. The Power Indicator blinks.
Page 88 Check if the power is on. Check if the power cord is securely connected. Check if a special fluorescent or neon lamp is on in the vicinity. Q & A How can I change the frequency? The frequency can be changed by reconfiguring the video card. Note That video card support can vary, depending on the version of the driver used.
Page 89 Set the resolution at the Control Panel → Display → Screen Saver. Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer Man- ual). How can I clean the outer case/LCD Panel? Disconnect the power cord and then clean the LCD Display with a soft cloth, using either a cleaning solution or plain water.
Page 90: Specifications
Dimensions (W x H x D) / Weight (With Stand) 780.0 x 545 x 311.0 mm / 30.7 x 21.5 x 12.2 inch / 13.7 kg / 30.2 lbs SyncMaster 320MP-2 32" Diagonal (80 cm) 697.68 mm (H) X 392.3 mm (V) 0.51075 mm (H) X 0.51075 mm (V)
Page 91 Dimensions (W x H x D) / Weight (With Stand) (With protection glass-option) 19.2 kg / 42.3 lbs VESA Mounting Interface 200 x 200 mm Environmental considerations Operating Storage Plug and Play Capability This LCD Display can be installed on any Plug & Play compatible system. The interaction of the LCD Display and the computer systems will provide the best operating conditions and LCD Display settings.
Page 92: Preset Timing Modes
Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows. Display Mode IBM, 640 x 350 IBM, 640 x 480...
Page 93: For Better Display
Information For Better Display Adjust the computer resolution and screen injection rate (refresh rate) on the computer as described below to enjoy the best picture quality. You can have an uneven picture quality on screen if the best picture quality is not provided for TFT-LCD. •...
Page 94 Turn the power off for 2 hours after 12 hours in use • Set the Monitor to power off with the PC Display Properties Power Scheme. • Use a Screen saver if possible - Screen saver in one color or a moving image is recom- mended.
Page 95: Select Method
- Cycle: Display moving image together with Logo for 60 seconds after 4 hours in use. • The best way to protect your monitor from Image retention is to turn Power off, or set your PC, or System to operate a Screen Saver program when you are not using it. Also Warranty service will be limited based on instruction guide.
Page 96 Note ( Please check CD's User Guide at "OSD Function", some model's will not available ) Apply the Screen Pixel function on Product • Apply the Screen Pixel function - Symptom: Dot with Black Color move up and down. - Select method •...
Page 97 - Select method • Instruction Guide : OSD Menu -> Set Up -> Safety Screen -> Eraser • Time Interval : 1 ~ 10 hours ( Recommend : 1 ) • Time Period : 10 ~ 50 second ( Recommend : 50 ) Note ( Please check CD's User Guide at "OSD Function", some model's will not available )
Page 98 Appendix Contact SAMSUNG WORLDWIDE Note If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. U.S.A CANADA MEXICO ARGENTINA BRAZIL CHILE COLOMBIA COSTA RICA ECUADOR EL SALVADOR GUATEMALA HONDURAS JAMAICA NICARAGUA PANAMA PUERTO RICO REP.
Page 99 022 - 607 - 93 - 33 PORTUGAL 808 20 - SAMSUNG (7267864) http://www.samsung.com/pt SLOVAKIA 0800 - SAMSUNG (726-7864) http://www.samsung.com/sk SPAIN 902 - 1 - SAMSUNG (902 172 678) SWEDEN 075 - SAMSUNG (726 78 64) SWITZERLAND 0848 - SAMSUNG (7267864, CHF 0.08/min)
Page 100 800-SAMSUNG(726-7864) http://www.samsung.com/ae 8000-4726 The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the resolution. The distance be- tween two dots of the same color is called the 'Dot Pitch'. Unit: The screen must be redrawn several times per second in order to create and display an image for the user.
Page 101: Correct Disposal
SRS TS XT Correct Disposal Correct Disposal of This Product (Waste Electrical & Electronic Equipment) - Europe only Correct disposal of batteries in this product - Europe only Authority Information in this document is subject to change without notice. curacy of the display. A high resolution is good for performing multiple tasks as more image information can be shown on the screen.
Page 102 Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden. Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or con- sequential damages in connection with the furnishing, performance, or use of this material.

Samsung SyncMaster 320MP-2 User Manual

Quick Links

LCD Monitor

User Manual

Troubleshooting

Related Manuals for Samsung SyncMaster 320MP-2

Summary of Contents for Samsung SyncMaster 320MP-2

Table of Contents