Advertisement
3. SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CP36B.V2
Battery: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.6V 1.3Ah Li-ion
Charging Time: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5hr
Maximum Torque: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.5Nm
No Load Speed: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210rpm
Vibration: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.48m/s²
Uncertainty: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.5m/s²
Noise Power: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71B(A)
Noise Pressure: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60B(A)
Contents:
Screwdriver Bits:
Slotted - 3 (x2), 4, 5mm
Philips - #0, #1, #2 (x2), #3,
Pozi - #0, #2, #3
TRX-Star* - T8, T10, T15, T20
Hex - 1.5, 4mm,
50mm Screwdriver Bits; Slotted - 4mm, Phillips - #2,
Magnetic Bit Holder
Drill Bits - 2, 2.5, 3mm.
4. OPERATION
IMPORTANT WARRANTY INFORMATION: The battery fitted to this cordless tool is considered to be a consumable item and its ability
to accept charge will reduce over time. Our warranty will cover genuine battery malfunction, but not fair wear and tear, for a period of 12
months.
4.1.
To charge the screwdriver, insert the charger jack into the charging socket on the screwdriver (fig.1) and plug the charger into a mains
socket.
4.2.
The red indicator light will illuminate to indicate the battery is being charged. When charging is complete, unplug the charger from
the mains and the screwdriver.
4.3.
When the green button is lit, the battery is fully charged.
4.4.
Place a bit into the bit holder of the screwdriver. Select the required direction by using the reverse switch (fig.1) (which will lock the
screwdriver in its central position) and squeeze the trigger to start the screwdriver. The LED worklight will light with initial pressure on the
trigger.
4.5.
The charge level indicator (fig.2) shows there is sufficient charge if all the LEDs illuminate, if just the yellow and red LEDs illuminate, the
screwdriver will soon need charging, if just the red LED illuminates, the screwdriver needs to be charged immediately.
4.6.
To change the position of the handle, press the handle lock (fig.2) and turn the handle around 180° until it clicks into position (fig.3).
4.7.
To select torque or drill setting, twist the torque selector (fig 1 ) around to the required setting - from 1 (the lowest) to 8 (the highest) for
torque setting or to the drill symbol for drilling.
4.8.
When finished working, remove the bit from the bit holder, pulling back the quick release bit holder. Clean the screwdriver and store in
a clean, dry, childproof location.
© Jack Sealey Limited
fig.1
fig.2
fig.3
Original Language Version
CP36B.V2 Issue 2(3) 28/09/2021
Advertisement
