To prevent accidents, which could cause serious injury or death, as well as machine damage read these instructions before installation and / or use. INTRODUCTION 1. IMPORTANT SAFETY INSTRUCTIONS 1.1 INSPECT THE DISHWASHER 2. TOOLS WHICH MAY BE NEEDED 3. MATERIALS WHICH MAY BE NEEDED 4.
INTRODUCTION NOTICE : Please read this installation manual Read these installation instructions and particularly the safety instructions completely before installing and follow completely and carefully. They will save you them carefully. Save these installation time and effort and help to ensure optimum instructions and pass them on to any dishwasher performance.
Only connect the dishwasher to the Old appliances may contain materials • • power supply when all installation and that can be recycled. Please contact plumbing work is complete. your local recycling authority about If the dishwasher is installed in a the possibility of recycling these •...
2. TOOLS WHICH MAY BE NEEDED 3. MATERIALS WHICH MAY BE NEEDED (Additional materials may be required to comply with local codes) Hot Water Supply Line - Minimum 3/8” O.D. copper tubing or metal braided dishwasher supply line. 90° elbow with 3/8” N.P.T. male threads on one leg, and sized to fit your water supply line (copper tubing/compression fitting, or braided hose) on the other leg.
4. MATERIALS SUPPLIED 4.1 PARTS SUPPLIED 4.4 DISHWASHER PARTS BAG 2 Parts for your dishwasher will come in several plastic bags. (MODEL DEPENDING) Check your parts bags shown In addition to the manual bag to make sure you have all the and the dishwasher parts bag parts as listed to the left.
Place the two mounting brackets into the top corners of the dishwasher. Bend sides of mounting brackets ( ) in order to fix from sides (if necessary). NOTICE : For thes model, DIN25400 note extra bending should be done that on the brackets as shown.
6.3 ADJUSTING HEIGHT Measure the height of the enclosure. 15 / (50mm) 6.3.1 INSTALLING THE FOOT SUPPORTS 15 / (50mm) 15 / (50mm) Supplied ( If the height of the enclosure is 337/16” to 341/4” (850mm - 870mm) use short 15 / ...
If the height of the enclosure is above 341/4” (870mm) use long supports as shown in the figure. Adjust the front foot level with the adjusting wrench to balance and raise the dishwasher to the enclosure height. Adjust the rear foot level with a screwdriver to balance and raise the dishwasher to the enclosure height.
6.5 PREPARING THE WATER CONNECTION (A) Install an easily accessible shut-off valve (not supplied) in the water supply line. All solder connections must be made before the water line is connected to the dishwasher’s water inlet valve. Water can also be supplied to the dishwasher by using a flexible braided hose line.
6.6 DRAIN PREPARATION The dishwasher drain hose may be connected to the drain plumbing in one of three ways (Figure NOTICE : Either one of the above methods must be used or the dishwasher will not operate • properly. A hose that attaches to a sink spray can burst if it is installed on the same water •...
6.7 STEAM PROTECTION FOIL Steam will form inside the dishwasher during operation. At the end of the cycle, when the dishwasher door is opened, it is required to use a steam protection foil to prevent any steam from collecting on the underside of the counter top. 6.6.2 FITTING THE PROTECTION FOIL Before applying the steam protection foil to the underside of the countertop, clean the area with...
7. PLACEMENT OF DISHWASHER INTO THE OPENING Now place the dishwasher into the opening and get ready to connect all hoses and electrical connections. CAUTION Make sure all hoses are pulled through the side opening of the cabinet, no hoses are kinked and all slack is taken out as shown in the above figure.
NOTICE : After connections are made turn on the water supply to check for leaks. 7.2 ELECTRICAL CONNECTION WARNING • Make sure the voltage and frequency listed on the data plate correspond with the household electrical supply. This data must correspond to prevent injury and machine damage.
Page 17
7.2.1 GROUNDING INSTRUCTIONS This appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment-grounding conductor and a grounding plug.
(Ø 1/8” x 1/8” - Ø 3.5mm x 14mm). Make sure you do not go through the top of the countertop or damage granite. NOTICE : For model, DIN25400, you should note that keep the total height of the dishwasher at (3,5mm) 321/4”...
Page 19
Lock the toe kick brackets as shown with the plastic tab in the figure C by pushing the plastic tab on the dishwasher into the teeth of the bracket ( 3. Now attach the toe kick to the bracket with the two (Ø...
7.5 INSTALLING THE OUTER DOOR (DIN25400) Measure the height and width of the enclosure (Figure ) and the toe kick. Determine how big the wooden door can be. For example if the height is 337/8” (860mm) and if the toe kick is 315/16”...
Page 21
4. Place the plastic mounting brackets over the marked holes and the side tabs must be flush with (3,5mm) Ø " the edge of the wooden door (Figure 5. Attach the two mounting brackets to the wooden door with 4 screws (Ø 1/8” x 5/8” (Ø 3.5mm x 14mm) (Figure 6.
Page 22
7. Open the door and remove the two caps and two screws inside the door at position 1 and 3 (Figure 8. Using the four screws Ø 3/16” x 111/16” (Ø 4mm x 43mm) provided, attach the wooden door to the dishwasher at position 1 and 3 (Figure Ø...
Page 23
ADJUSTING DOOR TENSION WITH CUSTOM WOODEN DOOR (DIN25400) Check the door tension of the dishwasher: If the door closes too quickly or if the door falls open, the spring tension needs to be adjusted.
Page 24
NOTICE : If you have a European kitchen or want to install a wooden toe kick to match your kitchen, please refer to one of the two drawings given below. Follow the same instructions on the brackets as for the removable toe kick. Installation should be done following the steps illustrated in the figures respectively.
8. INSTALLER CHECKLIST 10. SELF HELP HINTS: Your installer must have completed and The screen does not come on: checked the following: Check to make sure the breaker to the • The dishwasher is square and level. dishwasher is in the on position. •...