This guide addresses only those items. You should use good judgment to identify potential safety hazards due to attachment of non-Lenovo features or options not covered by this inspection guide.
4. Check for cracked or bulging batteries. 5. Remove the cover. 6. Check for any obvious non-Lenovo alterations. Use good judgment as to the safety of any non-Lenovo alterations. 7. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or other liquids, or signs of fire or smoke damage.
Grounding requirements Electrical grounding of the computer is required for operator safety and correct system function. Proper grounding of the electrical outlet can be verified by a certified electrician. Safety notices (multilingual translations) The safety notices in this section are provided in the following languages: •...
CRU list Table 1. Model: IP Flex 5 Chrome 13ITL6 (Machine type: 82M7) Type ac power adapter self-service Power cord self-service Lenovo USI Pen * self-service * for selected models Hardware Maintenance Manual...
Chapter 3. Identifying FRUs (CRUs) Locate FRUs and CRUs The exploded illustrations help Lenovo service technicians identify FRUs or CRUs that they may need to replace when servicing a customer’s computer. Figure 1. IP Flex 5 Chrome 13ITL6 exploded view...
Page 30
Table 2. FRU (CRU) categories FRU (CRU) category LCD unit Note: The LCD unit as a whole is not an FRU. It contains FRUs as its components. Upper case (with keyboard and touchpad) System board I/O board FFC I/O board cable Wi-Fi card Solid-state drive (SSD) Heat sink...
Page 31
Figure 2. IP Flex 5 Chrome 13ITL6 LCD unit- exploded view Table 3. FRU categories for the LCD unit FRU (CRU) category LCD cover EDP cable LCD module Camera AL foil Camera Microphone rubber Hinge rubber Hinge Strip cover Chapter 3 Identifying FRUs (CRUs)
Chapter 4. Removing a FRU or CRU Service tools The following table lists tools for servicing Lenovo computers. Tools with a cross mark are needed for serving the product models as described by this publication. Prepare them before you service the product.
3. Follow the correct sequence in the steps for removing an FRU, as shown in the illustrations by the numbers in square callouts. 4. When removing an FRU, move it in the direction as shown by the arrow in the illustration. 5.
Figure 4. Pry up the latches and remove the lower case Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement part: Lower case Remove the battery pack Make sure the following FRU (or CRU) has been removed.
Figure 6. Remove the SSD Number of screws Screw specifications M2 x L2 Go to to look up the Lenovo part number of the following replacement https://support.lenovo.com/partslookup part: Remove the Wi-Fi card Make sure the following FRU (or CRU) has been removed.
Figure 7. Remove the Wi-Fi card Screw specifications Number of screws M2 x L3 Go to to look up the Lenovo part number of the following replacement https://support.lenovo.com/partslookup part: Wi-Fi card Remove the I/O board cables Make sure the following FRU (or CRU) has been removed.
Go to to look up the Lenovo part numbers of the following https://support.lenovo.com/partslookup replacement parts: I/O board FFC I/O board cable Remove the I/O board Make sure the following FRU (or CRU) has been removed. “Remove the lower case” on page 28 Step 1.
Go to to look up the Lenovo part number of the following replacement https://support.lenovo.com/partslookup part: I/O board Remove the heat sink Make sure the following FRU (or CRU) has been removed. “Remove the lower case” on page 28 Step 1.
Figure 13. Remove the fan Screw specifications Number of screws M2 x L2 Go to to look up the Lenovo part number of the following replacement https://support.lenovo.com/partslookup part: Remove the speaker Make sure the following FRUs (or CRUs) have been removed.
Figure 14. Remove the speaker Go to to look up the Lenovo part number of the following replacement https://support.lenovo.com/partslookup part: Speaker Remove the system board Make sure the following FRUs (or CRUs) have been removed. “Remove the lower case” on page 28 “Remove the battery pack”...
Page 42
Figure 15. Disconnect cables connected to the system board Step 2. Remove ten screws. Figure 16. Remove ten screws Screw specifications Number of screws M2 x L2 M2.5 x L4 M1.6 x L3 Step 3. Open the hinge and then remove the system board. Hardware Maintenance Manual...
Figure 17. Remove the system board Go to to look up the Lenovo part number of the following replacement https://support.lenovo.com/partslookup part: System board Remove the LCD unit Make sure the following FRU (CRU) has been removed. “Remove the lower case” on page 28 Step 1.
Page 44
Figure 19. Remove the LCD module Screw specifications Number of screws M2.5 x L4 Step 4. Remove the LCD unit. Figure 20. Remove the LCD unit Hardware Maintenance Manual...
“Remove the system board” on page 35 “Remove the LCD unit” on page 37 Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement part: Upper case (with keyboard and touchpad) Disassemble the LCD unit The LCD unit as a whole is not an FRU. Instead, it contains FRUs as its components. Before disassembling the LCD unit, make sure it has been detached from the upper case.
“Remove the strip cover” on page 39 Step 1. Remove the hinge rubber carefully. Figure 22. Remove the hinge rubber Go to to look up the Lenovo part number of the following replacement https://support.lenovo.com/partslookup part: Hinge rubber Remove the LCD module Make sure the following FRUs (CRUs) have been removed.
Go to to look up the Lenovo part number of the following replacement https://support.lenovo.com/partslookup part: LCD module Remove the camera module Make sure the following FRUs (or CRUs) have been removed. “Remove the LCD unit” on page 37 “Remove the strip cover” on page 39 “Remove the hinge rubber”...
Figure 26. Remove the camera Step 4. Remove the microphone rubber. Figure 27. Remove the microphone rubber Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following replacement parts: Camera Camera AL foil Microphone rubber Remove the EDP cable Make sure the following FRUs (CRUs) have been removed.
Go to to look up the Lenovo part number of the following replacement https://support.lenovo.com/partslookup part: EDP cable Remove the hinge Make sure the following FRUs (CRUs) have been removed. “Remove the LCD unit” on page 37 “Remove the strip cover” on page 39 “Remove the hinge rubber”...
Page 50
“Remove the hinge rubber” on page 40 “Remove the LCD module” on page 40 “Remove the hinge” on page 43 Go to to look up the Lenovo part number of the following replacement https://support.lenovo.com/partslookup part: LCD cover Hardware Maintenance Manual...