Table of Contents
Advertisement
Chapter
2
Preparation
2
Thank you
Your new TV has many features and incorporates the latest technology to enhance your viewing
experience. We recommend that you spend some time reading this instruction manual so that you fully
understand these features. You will also find some hints and tips to help you resolve any issues.
Read all the safety instructions carefully before use and keep this instruction manual for future reference.
Unpacking the TV
Remove all packaging from the TV. Retain the packaging. If you dispose of it please do so according to local regulations.
The following items are included:
TV Stand Neck
GB
Instruction Manual
49" LED Smart 4K Ultra HD TV
LT-49C870(A)
Instruction Manual
JVC 49' LED Smart 4K Ultra HD TV LT-49C870(A) Manual.indd 7
for purchasing your new JVC TV.
Stand screws x8
TV Stand Base
3
Installing the Stand
Fitting the Stand Neck and Base Together
Quick Start Guide
1. Fit the neck onto the base.
2. Using 4 of the supplied screws, screw the neck to the base.
Fitting the Stand to the TV
49" LED Smart 4K Ultra HD TV
3. Ensure the TV is switched off and not connected to the mains power supply.
4. Lay the TV down on a flat surface ideally on the edge of a table so the base of the
TV slightly overhangs the edge of the table, with the back side facing up. Please
LT-49C870(A)
make sure a soft cushioned material (such as a dry bath towel or thick piece of
foam) is placed beneath the screen.
5. Slide the stand under the lip, the neck will fit snugly over the screw holes. Then
screw the stand to the TV using the 4 screws supplied.
Thank you
for purchasing your new JVC TV.
Your new TV incorporates the latest technology to enhance your viewing
experience. We would suggest that you allow about 20 mins for initial setup.
Please follow this guide for a successful first time installation.
Protective
Bag
The latest eco-friendly power-saving technology will switch off the TV if
it is left on and idle for 4 hours. Please refer to "Auto Standby" under the
"Time Settings" section of the instruction manual for more detail.
The LCD display is very fragile, and must be protected at all times when installing and removing the base stand. Be sure that no hard or sharp object,
1
Unpacking
or anything that could scratch or damage the LCD display, comes into contact with it. DO NOT exert pressure on the front of the TV at any time because
the screen could crack.
Remove all packaging from the unit. Retain the packaging. If you dispose of it please do so according to any local regulations.
4
TV
Remote Control/
Instruction Manual
Connecting the Aerial and Turning on the TV
TV Stand Neck
AAA Batteries x2
Quick Start Guide
Screws x 8
TV Stand Base
1. Connect one end of the RF coaxial cable
to the aerial socket on the wall and the
other end of the cable to the ANT socket
on the back of your TV.
Please inspect your TV for damage after unpacking. If you do notice any damage please consult your dealer.
2. Plug the TV into a mains socket and
switch on at the mains.
3. In standby mode, press the
the remote control to turn the TV on. The
2
Operating Your Remote Control
LED indicator will flash for a few seconds
then the TV will switch on.
1. Slide open the battery compartment on the back of the remote control.
2. Insert two AAA size batteries. Make sure to match the (+) and ( - )
ends of the batteries with the (+) and ( - ) ends indicated in the battery
compartment.
3. Slide the battery compartment cover back into place. Make sure it clicks
• Do not connect the TV to the mains supply until you have completed all the connections.
into place.
• Always disconnect the TV from the mains socket when not in use for a long period of time.
• The
To completely disconnect the mains power, please remove the mains plug from the mains socket.
JVC LT-49C870(A) LED Smart 4K Ultra HD TV Quick Start.indd 1
Quick Start Guide
LAN
SPDIF
VGA
Optic.OUT
SCART
Slide under
the lip
Cushioned
Table
material
Optional
If you want to connect to the internet via a wired connection then
connect your ethernet cable to the LAN socket.
button on
RF coaxial cable
(not included)
button on the remote control is only used for switching the TV into standby, it does not disconnect the TV from the mains power.
20/09/2017 16:49
2
3
.,/@
ABC
DEF
4
5
6
GHI
JKL
MNO
7
8
9
PQRS
TUV
WXYZ
0
TV
V
P
OK
EPG
TXT
LANG.
SUBT.
Remote Control /
AAA Batteries x 2
7
20/09/2017 17:04
Advertisement
Table of Contents
