1. Position the branch to be cut between the cutting
blade
and fixed blade
6
2. Push the lock-off button
switch
3
then squeeze the trigger switch
3. The cutting blade
6
will make a cut cycle and cut the
branch off.
nOTE: Cut branches at an angle for a cleaner cut.
4. Release the trigger switch.
nOTE: If more branches need to be cut, at the same time,
the lock-off switch
can be held down and actuate the
3
trigger switch
1
as needed. Otherwise, repeat steps 1-4.
MAINTENANCE
Your power tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regular cleaning.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can cause injury.
The charger and battery pack are not serviceable.
Removing and Installing Blade (Fig. A, F, G)
DANGER: RISK OF INJURY. WHEN REASSEMBLING THE
BLADE SYSTEM, ENSURE EACH PART IS REINSTALLED
CORRECTLY, AS DESCRIBED BELOW. IMPROPER ASSEMBLY
OF THE BLADE OR OTHER PARTS OF THE BLADE SYSTEM
CAN CAUSE SERIOUS INJURY.
DANGER: To reduce the risk of serious personal
injury, turn unit off, remove battery pack before
making any adjustments or removing/installing
attachments or accessories. An accidental start‑up can
cause serious personal injury.
WARNING:
protection. Be careful of the sharp edges on the blade.
Replacement blades are available from your nearest
authorised service centre. This pruner requires replacement
blade DWZPRB300.
1. Remove the battery.
2. Wear proper eye protection and gloves and be careful not
to cut yourself.
3. Place the product on a smooth, level surface.
4. Using the supplied hex wrench
screw
11
one full turn as shown in Fig. F. This will allow for
easier removal and assembly of the cutting blade
5. Flip the product onto its other side.
6. Using the hex wrench
screw
12
and nut
13
7. Remove the cutting blade
.
7
down and squeeze the lock-off
2
1
.
Use gloves and proper eye
loosen the fixed blade
10
remove the cutting blade
10
as shown in Fig. G.
6
as shown in Fig. G.
8. Install the new cutting blade.
nOTE: Ensure the cutting edge faces toward the fixed
cutting blade as shown in Fig. F.
9. Insert the cutting blade screw
blade and screw mount
10. Use the hex wrench to loosely tighten the cutting blade
screw
12
11. Flip the product onto its other side and use the hex
wrench
shown in Fig. G.
12. Flip the product onto its other side and use the hex
wrench
Blade Maintenance (Fig. H)
WARNING: Use gloves and proper eye protection while
removing, sharpening, and installing blade.
The cutting blades are made from high quality, hardened steel
and with normal usage, they will not require resharpening.
However, if you accidentally hit a wire fence, stones, glass, or
other hard objects, you may put a nick in the blade. There is no
need to remove this nick as long as it does not interfere with the
movement of the blade. If you drop the trimmer, carefully inspect
it for damage. If the blade is bent, housing cracked, handles
broken or if you see any other condition that may affect the tool's
operation contact your local authorized service center for repairs
before putting it back into use.
1. Remove the battery.
2. Remove blade from pruner. See instructions for Removing
and Installing Blade.
3. Wear proper eye protection and gloves and be careful not
to cut yourself.
4. Secure blade
5. Carefully file the cutting edge
a fine tooth file
included), maintaining the angle of the original cutting edge
of the cutting blade.
6. Inspect the edge of the fixed blade and remove any burrs
with a fine tooth file.
7. Install sharpened cutting blade as described in the
Removing and Installing Blade section.
Blade Lubrication (Fig. A)
1. After use, remove the battery
2. Carefully apply a resin solvent to the exposed blades.
Storage (Fig. A)
WARNING: Keep your hands away from the blade.
1. After use, remove the battery.
2. Store in a dry location, away from the reach of children.
.
6
C
Lubrication
Your power tool requires no additional lubrication.
12
14
into nut
.
10
to fully tighten the fixed blade screw
10
to fully tighten the cutting blade screw
6
in a vise
11
as shown in Fig. H.
12
of the cutting blade with
(not included) or sharpening stone (not
13
8
.
English
through the cutting
13
.
11
as
12
.
11