Contents Before working inside your computer........11 ..................... 11 Before you begin .................... 11 Safety instructions ..................12 Recommended tools After working inside your computer........14 Removing the base cover............15 ......................15 Procedure Replacing the base cover............18 ......................18 Procedure Removing the battery............... 19 .....................
Page 4
Removing the power-adapter port........25 .....................25 Prerequisites ......................25 Procedure Replacing the power-adapter port........27 ....................27 Post-requisites ......................27 Procedure Removing the hard drive............28 ....................28 Prerequisites ......................28 Procedure Replacing the hard drive............31 ......................31 Procedure ....................31 Post-requisites Removing the processor fan and heat-sink assembly..32 .....................32 Prerequisites ......................32...
Page 5
Removing the wireless card............ 39 .....................39 Prerequisites ......................39 Procedure Replacing the wireless card.............41 ......................41 Procedure ....................43 Post-requisites Removing the coin-cell battery..........44 ....................44 Prerequisites ......................44 Procedure Replacing the coin-cell battery..........47 ......................47 Procedure ....................47 Post-requisites Removing the speakers............48 ....................
Page 6
Removing the display assembly..........55 .....................55 Prerequisites ......................55 Procedure Replacing the display assembly..........61 ....................61 Post-requisites ......................61 Procedure Removing the system board............63 .....................63 Prerequisites ......................63 Procedure Replacing the system board............68 ......................68 Procedure ....................68 Post-requisites ........69 Entering the Service Tag in the BIOS setup program Removing the palm rest and keyboard assembly....
Page 7
Removing the display hinges..........76 .....................76 Prerequisites ......................77 Procedure Replacing the display hinges...........79 ......................79 Procedure ....................79 Post-requisites Removing the camera.............. 80 ....................80 Prerequisites ......................80 Procedure Replacing the camera...............83 ......................83 Procedure ....................83 Post-requisites Removing the sensor board............ 84 ....................
Page 8
.............90 Getting the Dell Webcam Central ......................91 Display ................91 Adjusting the brightness ..............91 Changing the screen resolution ................... 92 Rotating the display .................. 92 Cleaning the display ........................ 93 HDMI ............93 Connecting to external display devices ......................95 Graphics ..............95...
Page 9
................104 Browsing a media card ......................105 Keyboard ............105 Changing the keyboard language ..................105 Keyboard shortcuts ......................106 Touch pad ................ 106 Identifying the touch pad ................. 107 Touch pad gestures ....................107 Power adapter ......................108 Battery ......................108 Chipsets ..............108 Downloading the chipset driver ................
Page 10
Getting help and contacting Dell.........120 ..................120 Self-help resources ....................121 Contacting Dell...
Before working inside your computer NOTE: The images in this document may differ from your computer depending on the configuration you ordered. Before you begin Save and close all open files and exit all open applications. Shut down your computer. The shut-down instruction varies depending on the operating system installed on your computer.
CAUTION: You should only perform troubleshooting and repairs as authorized or directed by the Dell technical assistance team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. See the safety instructions that shipped with the product or at www.dell.com/regulatory_compliance.
After working inside your computer CAUTION: Leaving stray or loose screws inside your computer may severely damage your computer. Replace all screws and ensure that no stray screws remain inside your computer. Connect any external devices, peripherals, or cables you removed before working on your computer.
After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Procedure Close the display and turn the computer over. Using a screw driver, remove the screw cover located at the center of the base cover.
Page 16
Remove the screws that secure the base cover to the palmrest and keyboard assembly. screws (9) base cover...
Page 17
Using a plastic scribe, pry the base cover from the palmrest and keyboard assembly. plastic scribe base cover...
After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Procedure Slide the tabs on the base cover into the slots on the palmrest and keyboard assembly and snap the base cover into place.
Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Prerequisites Remove the base cover. Procedure Remove the screw that secures the battery to the palmrest and keyboard assembly.
Page 20
Lift the battery off the palmrest and keyboard assembly. battery cable screw battery palmrest and keyboard assembly Turn the computer over. Press and hold the power button for 5 seconds to ground the system board.
After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Procedure Align the screw hole on the battery with the screw hole on the palmrest and keyboard assembly.
After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Procedure Open the latch and disconnect the power and volume-buttons board cable from the I/O board.
Using a plastic scribe, pry the power and volume-buttons board, along with its cable, off the palmrest and keyboard assembly. power and volume-buttons latch board cable tape plastic scribe power and volume-buttons palmrest and keyboard board assembly Prerequisites Remove the base cover.
After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Procedure Place the power and volume-buttons board into the slot on the palmrest and keyboard assembly.
Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Prerequisites Remove the base cover. Remove the battery.
Page 26
Lift the power-adapter port with its cable, off the palmrest and keyboard assembly. power-adapter port cable screw power-adapter port...
Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Post-requisites Replace the battery. Replace the base cover.
After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. CAUTION: Hard drives are fragile. Exercise care when handling the hard drive. CAUTION: To avoid data loss, do not remove the hard drive while the computer is in sleep or on state.
Page 29
Lift the hard-drive assembly off the palmrest and keyboard assembly. NOTE: The images in this chapter may differ from your computer depending on the processor you ordered. screws (3) hard-drive assembly palmrest and keyboard assembly Remove the screws that secure the hard-drive bracket to the hard drive.
Page 30
Lift the hard drive from the hard-drive bracket. screws (4) hard-drive bracket hard drive...
After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. CAUTION: Hard drives are fragile. Exercise care when handling the hard drive. Procedure Align the screw holes on the hard drive with the screw holes on the hard- drive bracket.
After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. WARNING: The heat sink may become hot during normal operation. Allow sufficient time for the heat sink to cool before you touch it.
Page 33
Lift the processor fan and heat-sink assembly off the system board. processor fan and heat-sink captive screws (4) assembly tape system board...
After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Procedure Align the screw holes on the processor fan and heat-sink assembly with the screw holes on the system board.
Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Prerequisites Remove the base cover. Remove the battery.
Procedure Open the latches and disconnect the I/O-board cable, power and volume-buttons board cable, and sensor board cables from the I/O board. I/O-board cable latch sensor-board cable I/O board power and volume-buttons board cable...
Page 37
Remove the screw that secures the I/O board to the palmrest and keyboard assembly. screw I/O board palmrest and keyboard assembly Lift the I/O board off the palmrest and keyboard assembly.
After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Procedure Place the I/O board on the palmrest and keyboard assembly. Align the screw hole on the I/O board with the screw hole on the palmrest and keyboard assembly.
Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Prerequisites Remove the base cover. Remove the battery.
Page 40
Slide the wireless card from the wireless-card slot on the system board. screw wireless-card bracket antenna cables (2) wireless card wireless-card slot...
After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Procedure CAUTION: To avoid damage to the wireless card, do not place any cables under it.
Page 42
Align the screw hole on the wireless-card bracket with the screw hole on the wireless card and tighten the captive screw that secures the wireless- card bracket to the wireless card, The following table provides the antenna-cable color scheme for the wireless card supported by your computer.
After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. CAUTION: Removing the coin-cell battery resets the BIOS setup program’s settings to default. It is recommended that you note the BIOS setup program’s settings before removing the coin-cell battery.
Page 45
Open the latch and disconnect the I/O-board cable from the system board. routing guide antenna cable I/O-board cable latch coin-cell battery cable Turn the I/O-board cable over to expose the coin-cell battery.
Page 46
Pry the coin-cell battery from the palm-rest assembly. I/O-board cable coin-cell battery coin-cell battery cable...
After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Procedure With the positive-side facing up, place the coin-cell battery into the battery socket on the system board.
Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Prerequisites Remove the base cover. Remove the battery.
Page 49
Release the speakers from the alignment posts and lift the speakers off the palmrest and keyboard assembly. routing guide coin-cell and antenna cables speakers (2) speaker cable...
After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Procedure Using the alignment posts on the palmrest and keyboard assembly, place the speakers on the palmrest and keyboard assembly.
Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Prerequisites Remove the base cover. Remove the battery.
Page 52
Turn the keyboard cable over and place it on the system board. tapes touch-pad cable latch touch pad keyboard cable Remove the screws that secure the touch pad to the palmrest and keyboard assembly.
Page 53
Slide and remove the touch pad away from the palmrest and keyboard assembly. screws (4) touch pad palmrest and keyboard assembly...
After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Procedure Slide the tabs on the touch pad into the slots on the palmrest and keyboard assembly.
Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Prerequisites Remove the base cover. Remove the battery.
Page 56
Open the latch and disconnect the display cable. screw display-cable bracket display cable tape latch Open the latch and disconnect the sensor-board cable from the I/O board. Remove the antenna cable from the routing guide on the right speaker.
Page 57
Open the latch and disconnect the I/O-board cable from the system board. latch sensor-board cable antenna cable routing guide I/O-board cable latch...
Page 58
Peel the tapes off the display hinges. I/O-board cable tape...
Page 59
Turn the computer over and open the display as far as possible. CAUTION: Place the computer on a soft and clean surface to avoid scratching the display. display assembly palm-rest assembly 10 Place the computer face down on a flat surface. 11 Remove the screws that secure the display assembly to the palmrest and keyboard assembly.
Page 60
12 Lift the display assembly off the palmrest and keyboard assembly. display assembly screws (4) palmrest and keyboard assembly...
Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Post-requisites Replace the wireless card. Replace the battery.
Page 62
11 Replace the screw that secures the display-cable bracket to the system board.
After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. NOTE: Your computer’s Service Tag is stored in the system board. You must enter the Service Tag in the BIOS setup program after you replace the system board.
Page 64
Disconnect the coin-cell battery and speaker cables from the system board. I/O-board cable latch coin-cell battery cable speaker cable system board Remove the screws that secure the display-cable bracket to the system board and lift the display-cable bracket off the system board.
Page 65
Disconnect the display cable from the system board. screw display-cable bracket display cable tape latch system board Open the latch and disconnect the touch-pad cable from the system board. Open the latch and disconnect the keyboard cable from the system board.
Page 66
Disconnect the power-adapter port cable from the system board. system board power-adapter port cable latch touch-pad cable keyboard cable Remove the screw that secures the system board to the palmrest and keyboard assembly.
Page 67
Lift the system board off the palmrest and keyboard assembly. system board palmrest and keyboard assembly...
After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. NOTE: Your computer’s Service Tag is stored in the system board. You must enter the Service Tag in the BIOS setup program after you replace the system board.
Entering the Service Tag in the BIOS setup program Turn on or restart your computer. Press F2 when the Dell logo is displayed to enter the BIOS setup program. Navigate to the Main tab and enter the Service Tag in the Service Tag Input field.
Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Prerequisites Remove the base cover. Remove the battery.
After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Procedure Place the palmrest and keyboard assembly on a flat surface with the keyboard facing down.
Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Prerequisites Remove the base cover. Remove the battery.
Page 74
Using a plastic scribe, pry the display panel off the display-back cover. display panel display hinges (2) routing guide sensor-board cable plastic scribe display cable display-back cover...
After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Procedure CAUTION: Place the computer on a soft and clean surface to avoid scratching the display.
Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Prerequisites Remove the base cover. Remove the battery.
Procedure Peel the tapes and remove the antenna cables from the routing guide on the hinge cover. antenna cables (2) tape hinge cover (2) Remove the screws that secure the display hinges to the display back- cover and antenna assembly.
Page 78
Lift the display hinges off the display back-cover and antenna assembly. screws (6) display back-cover and antenna assembly hinges (2)
After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Procedure Align the screw holes on the display hinges with the screw holes on the display back-cover and antenna assembly.
Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Prerequisites Remove the base cover. Remove the battery.
Page 81
Peel the tape that secures the display cable to the display panel. display panel latch display cable tape Using a plastic scribe, pry the camera off the display-back cover.
Page 82
Turn over the camera and disconnect the camera cable from the camera. plastic scribe camera camera cable display-back cover...
After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Procedure Connect the camera cable to the camera. Using the alignment post, place the camera on the display-back cover and snap it into place.
Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Prerequisites Remove the base cover. Remove the battery.
Page 85
Using a plastic scribe, pry the sensor board off the display-back cover. sensor-board cable latch plastic scribe sensor board...
After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Procedure Align the sensor board on the display-back cover and snap the sensor board into place.
You may need to flash (update) the BIOS when an update is available or when you replace the system board. To flash the BIOS: Turn on your computer. Go to www.dell.com/support. Click or tap Product support, enter the Service Tag of your computer, and then click or tap Submit.
Technology and components Audio The Inspiron 11-3169 is shipped with Realtek ALC3246 with Waves MaxxAudio, which is the utility to adjust various audio settings. NOTE: The audio drivers are already installed when you receive your computer. Downloading the audio driver Turn on your computer.
Changing the audio settings On the taskbar, click or tap the search box, and then type Dell Audio. Click or tap Dell Audio and change the audio settings as required. Camera The Inspiron 11-3169 is shipped with an integrated 0.92 megapixel high- speed camera with a maximum of 1280 x 720 HD resolution at 30 FPS.
Click or tap Camera. Getting the Dell Webcam Central A CD is shipped along with your computer, which contains the Dell Webcam Central software. If you do not have the software, you can download it by registering through My Account on the Dell website.
Display The Inspiron 11-3169 is shipped with 11.6-inch full HD touch screen with 1366 x 768 resolution. Adjusting the brightness Right-click or touch and hold on your desktop and select Display settings. Drag or swipe the Adjust brightness level slider to adjust the brightness.
Select the desired resolution from the drop-down list. Rotating the display Right-click or touch and hold on your desktop. Select Graphics Options → Rotation and select from the following options. The display can also be rotated using the following key combinations: –...
Let the display dry thoroughly before you turn it on. HDMI The Inspiron 11-3169 supports HDMI to connect a TV or another HDMI-in enabled device. It provides video and audio output. The HDMI port is located on the left side of your computer.
Page 94
Select one of the following display modes: – PC screen only – Duplicate – Extend – Second screen only NOTE: For more information, see the document that shipped with your display device.
Graphics The Inspiron 11-3169 is shipped with Intel HD Graphics 515 - Intel Core i3. Downloading the graphics driver Turn on your computer. Go to www.dell.com/support. Click or tap Product support, enter the Service Tag of your computer, and then click or tap Submit.
Changing the display settings in Intel HD Graphics Control Panel Right-click or press and hold on the desktop and select Graphics Properties to launch the Intel HD Graphics Control Panel. Click or tap Display. Change the display settings as required. Intel WiDi The wireless display feature allows you to share your computer display with a compatible TV without using cables.
Downloading the WiDi application Turn on your computer. Go to www.dell.com/support. Click or tap Product support, enter the Service Tag of your computer, and then click or tap Submit. NOTE: If you do not have the Service Tag, use the auto-detect feature or manually browse for your computer model.
Enabling or disabling the USB in system setup Turn on or restart your computer. Press F2 when the Dell logo is displayed on the screen to enter the System Setup. The System Setup is displayed. On the left pane, select Settings → System Configuration → USB Configuration.
USB devices. Follow these steps to fix the no-boot issue: Turn on or restart your computer. Press F2 when the Dell logo is displayed on the screen to enter the System Setup. The System Setup is displayed.
Press and hold Wi-Fi, and then click or tap Go to settings. A list of available networks is displayed. Select your network and click or tap Connect. NOTE: Type the network security key, if prompted. Bluetooth The Inspiron 11-3169 is shipped with Bluetooth 4.0.
Turning Bluetooth on or off NOTE: There is no physical switch to enable or disable Bluetooth. It has to be done through the computer settings. Swipe-in from the right edge of the display, or click or tap the Action Center icon on the taskbar to access the Action Center. Click or tap Bluetooth to turn Bluetooth on or off.
Click or tap Yes to confirm the passcodes on both the devices. Removing the Bluetooth device Swipe-in from the right edge of the display, or click or tap the Action Center icon on the taskbar to access the Action Center. Touch and hold Bluetooth, and then click or tap Go to settings.
Select your Bluetooth device. Click or tap Send or receive files via Bluetooth. In the Bluetooth File Transfer window, click or tap Send files, and then select the desired file. Hard drive The following table shows the hard-drive options available in Inspiron 11-3169.
Identifying the hard drive in BIOS setup program Turn on or restart your computer. Press F2 when the Dell logo is displayed on the screen to enter the BIOS setup program. A list of hard drives is displayed under the System Information in the General group.
Keyboard The Inspiron 11-3169 is shipped with a backlit keyboard. Changing the keyboard language Click or tap Start Click or tap Settings Click or tap Time & language → Region & language. Click or tap Add a language. Choose the language you want to add and select a country for the language.
Turn off/on wireless Scroll lock Touch pad The Inspiron 11-3169 is shipped with a Precision touch pad. A precision touch pad is a new class of input device that provides high precision pointer input and gesture functionality. Precision touch pads interact with the operating system directly without a driver.
Touch pad gestures Gesture Procedure Result Tap to click Tap on the touch pad. Selects an item Tap, tap-slide to Tap, tap-slide on the Highlights text, and drags highlight or drag touch pad and drops an item Slide to scroll Place two fingers on the Scrolls the page.
Battery The Inspiron 11-3169 is shipped with a 2-cell 32 WHr smart lithium ion battery. NOTE: Batteries are covered for a period of one year from the invoice date unless stated otherwise in the invoice. Chipsets The chipset is virtually divided into two sections — Northbridge and Southbridge.
Expand System devices. Memory Your computer supports 4 GB, DDR3L memory of up to 1600 MHz. Checking the system memory in Windows Click or tap Start Select Settings Click or tap System → About.
The memory information is displayed on the right pane. Testing memory using ePSA Turn on or restart your computer. Press F12 after the Dell logo is displayed on the screen to access the boot menu. Use the arrow keys to highlight the Diagnostics menu option and press Enter.
Click or tap the Performance tab to display the processor performance details. Identifying the processors in Windows On the taskbar, click or tap the search box, and then type Device Manager. Click or tap Device Manager. The Device Manager window is displayed. Expand Processors .
Operating System The Inspiron 11-3169 is shipped with the Windows 10 factory installation. Service Tag location The service tag is a unique alphanumeric identifier that allows Dell service technicians to identify the hardware components in your computer and access warranty information.
Intel Trusted Execution Engine Interface In the Device Manager, check if the Intel Trusted Execution Engine Interface driver is installed. Install the driver update from www.dell.com/support.
Intel Virtual Button driver In the Device Manager, check if the Intel Virtual Button driver is installed. Install the driver updates from www.dell.com/support.
Intel Wireless 3165 WiFi and Bluetooth drivers In the Device Manager, check if the network card driver is installed. Install the driver updates from www.dell.com/support. In the Device Manager, check if the Bluetooth driver is installed. Install the driver updates from www.dell.com/support.
Entering the BIOS setup program Turn on or restart your computer. Press F2 when the Dell logo is displayed on the screen to enter the BIOS setup program. You can change the user-defined settings in BIOS setup program. Boot menu The Inspiron 11-3169 includes a one-time boot menu.
Page 119
To prevent the keyboard from locking, wait until the keyboard is initialized completely. The keyboard is initialized if one of the following occurs: • The keyboard lights flash. • The F2=Setup prompt appears in the top-right corner of the screen during boot.
Page 120
Getting help and contacting Dell Self-help resources You can get information and help on Dell products and services using these self-help resources: Information about Dell products and www.dell.com services Windows 8.1 and Windows 10 Dell Help & Support app Windows 10 Get started app Windows 8.1...
Page 121
Contacting Dell To contact Dell for sales, technical support, or customer service issues, see www.dell.com/contactdell. NOTE: Availability varies by country and product, and some services may not be available in your country. NOTE: If you do not have an active internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog.