Table of Contents
Advertisement
Quick Links
Instruction and safety manual
Model
Improper use of this Nailer can result in death or serious injury!
This Manual contains important information about product safety.
Read and understand this Manual before operating the Nailer.
Never allow anyone who has not reviewed this manual.
NT 65MA4
DANGER
Finish Nailer
Advertisement
Table of Contents
Related Manuals for Hitachi NT 65MA4
Summary of Contents for Hitachi NT 65MA4
- Page 1 Instruction and safety manual Model Finish Nailer NT 65MA4 DANGER Improper use of this Nailer can result in death or serious injury! This Manual contains important information about product safety. Read and understand this Manual before operating the Nailer. Never allow anyone who has not reviewed this manual.
-
Page 2: Table Of Contents
BEFORE OPERATION ..........8 DEFINITIONS OF SIGNAL WORDS ......3 Working environment ........... 9 EXPLANATION OF THE NAILING ACTION OF Air supply ............. 9 THE HITACHI NAILER .......... 3 Lubrication ............10 Cold weather care ..........10 SAFETY Testing the nailer..........10 IMPORTANT SAFETY INSTRUCTIONS FOR Adjusting air pressure ........ -
Page 3: Important Information
CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury, or may cause machine damage. NOTE emphasizes essential information. EXPLANATION OF THE NAILING ACTION OF THE HITACHI NAILER ○ SINGLE ACTUATION MECHANISM (SINGLE SEQUENTIAL ACTUATION MECHANISM): First, press the push lever against the wood;... -
Page 4: Safety
English SAFETY IMPORTANT SAFETY INSTRUCTIONS FOR USING NAILERS READ ALL INSTRUCTIONS 4. Keep fi ngers away from trigger when DANGER not driving fasteners to avoid accidental fi ring. 1. Operators and others in work area must Never carry the Nailer with fi nger on wear safety glasses with side shields. - Page 5 13. Dress properly. This Hitachi nailer includes a fastening Do not wear loose clothing or jewelry as operation switching device. they can be caught in moving parts. Before starting work, check the setting of Rubber gloves and nonskid footwear are the operation switching device.
-
Page 6: Employer's Responsibilities
6) it is not in use; lead to malfunction and resulting injuries. 7) leaving work area; Only service personnel trained by Hitachi, 8) moving it to another location; and distributor or employer shall repair the 9) handing it to another person. -
Page 7: Operation
English OPERATION NOTE The information contained in this Manual is designed to assist you in the safe operation of the Nailer. Some illustrations in this Manual may show details or attachments that diff er from those on your own Nailer. NAME OF PARTS Nailing operation Switching device Enlarged view... -
Page 8: Specifications
Min. Max. 1 quart (1 ltr) can (Code No.876212) NOTE Accessories are subject to change without .095” (2.4mm) any obligation on the part of HITACHI. APPLICATIONS ○ Manufactured Housing, On-site and Mobile Home Construction. ○ Cabinets, Furniture, and Woodworking. BEFORE OPERATION Read section titled “SAFETY”... -
Page 9: Working Environment
The lubricator supplies an oil mist to the unauthorized personnel. Nailer. Air supply Inspect the lubricator before operation to be sure the supply of lubricant is adequate. DANGER Use Hitachi pneumatic tool lubricant. ● NEVER oxygen or other Regulator bottled gases. -
Page 10: Lubrication
Filter-regulator-lubricator units should is operating properly. always be used. Keep the lubricator fi lled with Hitachi Before actually beginning the nailing work, pneumatic tool lubricant. test the Nailer by using the check list below. ○ If a lubricator is not available, supply 5 – 10 Conduct the tests in the following order. - Page 11 English (2) Adjust the air pressure to 70 psi (4.9 bar 5 □ The nailer must not operate. kgf/cm Connect the air hose. Do not load any nails in the Nailer. Set the switching device to the upward position (SINGLE ACTUATION MECHANISM).
-
Page 12: Adjusting Air Pressure
English (7) If no abnormal operation is observed, you (2) Slide the nail strip forward in the magazine. may load nails in the Nailer. The nail strip should pass the nail stopper. Drive nails into the workpiece that is the same type to be used in the actual application. -
Page 13: Nailer Operation
5) moving it to another location; ● NEVER point tool 6) handing it to another person. yourself others work This Hitachi nailer is equipped with a nailer area. operation switching device. ● Keep fi ngers Use SINGLE ACTUATION MECHANISM or... - Page 14 ● Please note that SINGLE ACTUATION MECHANISM of this Hitachi nailer will drive a nail each time the push lever is pressed Trigger against the wood as long as the trigger is pressed. (2) Continuous operation (Push lever fi re) ●...
-
Page 15: Adjusting The Nailing Depth
● After nailing: 1) disconnect air hose from the Nailer; 2) remove all nails from the Nailer; 3) supply 5 – 10 drops of Hitachi pneumatic tool lubricant into the air plug on the Nailer; and 1 Downward position 4) open the petcock on the air compressor tank to drain any moisture. -
Page 16: Using The Blow Nozzle
English ● Oil in the body or drained water from the 5 DISCONNECT AIR HOSE FROM NAILER. compressor can sometimes spout out 6 Choose a suitable position for the adjuster. of the air outlet. It is recommended that you once conduct a test before use and Turn Adjuster Flush Too Deep... - Page 17 English Disconnect Nose Cap air hose Push Lever Nose Cap Magazine NOTE ● The nose cap may reduce nailing depth due to its thickness. Re-adjustment of nailing depth is required.
-
Page 18: Maintenance
2 Clean the magazine. Remove dust which may have accumulated in the ● Disconnect air hose and remove all magazine. nails from Nailer when: 3 Lubricate the nail rail with Hitachi 1) doing maintenance pneumatic tool lubricant. inspection; and 2) clearing a jam. - Page 19 6. Operator troubleshooting (See page 21) 7. Service parts list CAUTION Repair, modifi cation and inspection of Hitachi Power Tools must be carried out by a Hitachi Authorized Service Center. This Parts List will be helpful if presented with the tool to the Hitachi Authorized Service Center when requesting repair or other maintenance.
-
Page 20: Service And Repairs
All quality Nailers will eventually require servicing or replacement of parts because of wear from normal use. NOTE Specifi cations are subject to change without any obligation on the part of HITACHI. Maintenance chart ACTION Prevent accumulation of Drain air line fi lter daily. - Page 21 English Operator troubleshooting Most minor problems can be resolved quickly and easily using the table below. If problems persist, contact a Hitachi authorized service center for assistance. PROBLEM CHECK METHOD CORRECTION Nailer operates, but no nail is Check for a jam.
- Page 23 CAUTION PLATE GASKET (B) CAP (A) HEX. SOCKET HD. BOLT M5 × 16 AIR PLUG NPT 1/4 HITACHI PLATE ROLL PIN D3 × 22 ROLL PIN D3 × 30 TRIGGER (C) TRIGGER ARM (C) Learn more about air tools and compressors we have.