Related Manuals for Philips EasyAir SNS212 MC
Summary of Contents for Philips EasyAir SNS212 MC
- Page 1 Sensors EasyAir SNS212 MC Design-in Guide Single, compact, cost-effective luminaire control Philips EasyAir SNS212 MC April 2023...
-
Page 2: Table Of Contents
Recommendations to design-in EasyAir SNS212 MC with good RF signal Mounting to a luminaire Mounting in a bracket (SMB-50) Installing EasyAir SNS212 MC with ceiling mount bracket (SNS212 MC CMP) Labels EasyAir SNS212 MC with multiple Philips Xitanium SR LED drivers (1:N application) -
Page 3: Introduction To This Guide
Introduction to this guide Thank you for choosing Philips EasyAir SNS212 MC. In this guide luminaire manufacturers will find the information required to design this product into a luminaire and configure it to suit specific applications. This design-in guide covers sensor functionality, mechanical mounting, wiring details, configuration and commissioning (grouping) method, application notes and frequently asked questions. -
Page 4: Warnings And Instructions
Warnings and instructions • EasyAir SNS212 MC must be used with SR LED drivers, e.g. Philips Xitanium SR drivers. • Do not apply mains power directly to the sensor. • Do not cover the sensor during operation or mount the sensor internal to the luminaire. -
Page 5: Introduction Of Easyair Sns212 Mc
Introduction of EasyAir SNS212 MC The Philips EasyAir SNS212 MC is the ideal solution for per-luminaire control of smart luminaires. It is the future proof successor of Philips EasyAir SNS210 MC. Occupancy sensing, daylight harvesting and task tuning are combined in a single, compact package for easy OEM luminaire assembly. -
Page 6: Product Characteristics
• Zigbee/BLE • Light sensor antenna • LED indicator EasyAir SNS212 MC is designed for a typical indoor environment (open/private offices, conference rooms, classrooms, corridors, etc.) in normally heated and ventilated areas. The sensor is normally mounted to a luminaire and is optimized for a sensor mounting height of 2.5 m to 3 m. -
Page 7: Motion Detector
Minor movement Major movement Height (H) 2.4m 3.0m Figure 1. Motion detection area. H: sensor installation height from floor. Minor movement detection area: X1 by Y1. Major movement detection area: X2 by Y2. April 2023 Design-in Guide - EasyAir SNS212 MC... -
Page 8: Sensor View Shield
To prevent false triggers, the EasyAir SNS212 MC must be mounted more than 2 m away from air vents in all directions, see figures below: > 2m Luminaire > 2m > 2m > 2m Sensor view shield The sensor comes with an occupancy view shield that can be used to block the movement detection by the sensor in a certain area. -
Page 9: Light Sensor
The EasyAir SNS212 MC converts the illuminance signal into ON/OFF or dimming commands to the Philips Xitanium SR LED driver in order to maintain a constant light level on the desk. Window The sensor should be installed with a minimum distance of 0.6 m to the window to avoid the sensor looking outside. -
Page 10: Daylight Regulation And Calibration
"Calibrate Daylight Sensor". Leave the room. • To calibrate, the light output of the luminaires first goes to a low level and to a high level before it regulates to the set light level. April 2023 Design-in Guide - EasyAir SNS212 MC... -
Page 11: Mechanical Design-In
Note: Stranded wires without ferrule should be soldered 5°~7° Angle Max Inserting solid conductors via push-in terminal [ Inserting solid conductors via push-in terminal ] Wire separation from the connector 1. Push April 2023 Design-in Guide - EasyAir SNS212 MC... -
Page 12: Wire Distance For Remote Mounting
Xitanium SR LED driver less than 2 m and meet the wire gauge requirement to guarantee the performance. Luminaire-to-luminaire distance If multiple luminaires with EasyAir SNS212 MC are used in the same area, the distance between the different sensors should be kept at least 1.5 m. This distance will minimize a sensor from “seeing”... -
Page 13: Mounting To A Luminaire
Mounting in a luminaire EasyAir SNS212 MC is a luminaire-mount sensor that is LED module directly powered by a Xitanium SR LED driver. It can be mounted to a slot or a cut-out in sheet metal. SNS212 Light shield Note: When daylight sensing is enabled, it is advised to... -
Page 14: Mounting In A Bracket (Smb-50)
Mounting in a bracket (SMB-50) 65 Max. The EasyAir SNS212 MC can be mounted in a bracket (SMB 50). Refer the figures for details on mounting and design- in into luminaire. All dimensions are in mm. 26 Max. 64 Max. -
Page 15: Installing Easyair Sns212 Mc With Ceiling Mount Bracket (Sns212 Mc Cmp)
Installing EasyAir SNS212 MC with ceiling mount bracket (CMP/W) The ceiling mount CMP bracket is available as a bracket without any pre-mounted sensor or cable. The luminaire manufacturer needs to mount the sensor in the CMP bracket and attach cable to it. The cable and screws are available with the accessory. -
Page 16: Labels
For a network application using a gateway, the labels can be used to identify a luminaire and where it is installed in the building. • Label 1 - Apply to the luminaire • Label 2 - Apply to the floor plan • Label 3 - Remains on the sensor April 2023 Design-in Guide - EasyAir SNS212 MC... -
Page 17: Easyair Sns212 Mc With Multiple Philips Xitanium Sr Led Drivers (1:N Application)
RSET2 NEUTRAL SGND LINE Each SR driver provides approximately 55mA of current on NFC ANTENNA the DALI bus, and EasyAir SNS212 MC is limited to 250mA. Connectors LED+ EasyAir SNS212 MC sends commands to all connected LED+ LED- Enable DALI PS LED- drivers (using broadcast command);... -
Page 18: Luminaire Production Test
Luminaire Production Test To ensure that a luminaire has been assembled correctly i.e. the wiring of the EasyAir SNS212 MC sensor to Xitanium SR driver is correct; a visible check can be made. The luminaire on power up dims up to 30% of maximum light output in the 1st second followed by dimming up to 100% in the next second. -
Page 19: Faq
Can you use a wall dimmer with EasyAir SNS212 MC? SNS212 MC can be used with a wireless wall dimmer, e.g., Zigbee green power switch. For list of supported switches, please visit our website How does EasyAir SNS212 MC compare to Philips ActiLume? Occupancy sensing and daylight harvesting are similar. - Page 20 Does EasyAir SNS212 MC make sense if I only want to do Yes. Keep “Occupancy Control” enabled in MC App and occupancy sensing? disable “Daylight Control” Is EasyAir SNS212 MC “failsafe”? Unlike traditional occupancy sensors, EasyAir SNS212 MC does not have a mechanical relay. This is a benefit of Philips SR LED drivers, as on/off is done relay-free within the driver.
-
Page 21: Contact Details
Contact details Philips EasyAir SNS212 MC Product information: www.lighting.philips.co.uk/oem-emea/products/easy-to- integrate-wireless-sensors.html Or contact your local Philips sales representative. April 2023 Design-in Guide - EasyAir SNS212 MC... -
Page 22: Disclaimer
Signify. Signify gives no warranties regarding these and assumes no legal liability or responsibility for any loss or damage resulting from the use of the information thereto given here. April 2023 Design-in Guide - EasyAir SNS212 MC... - Page 23 The information presented in this document is not intended as any commercial offer and does not form part of any quotation or contract. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. All other trademarks are owned by Signify Holding or their respective owners.