Sealey RJA1800.V4 Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear safety
instructions footwear
1. SAFETY
The user shall work only in accordance with this instruction manual.
9
The operator shall be provided with all necessary information about training and about pumping and translating
9
forces.
Ensure the jack is in sound condition and good working order. Take action for immediate repair or replacement
9
of damaged parts. Use genuine parts only. DO NOT modify the jack. The use of non-genuine parts may be
dangerous and will invalidate the warranty.
Locate the jack in a suitable, well lit working area.
9
Keep working area clean and tidy and free from unrelated materials. Use jack on level and solid ground,
9
preferably concrete. Avoid tarmacadam as jack may sink in.
Chock wheels of vehicle.
9
Ensure the vehicle handbrake is engaged, engine is switched off and transmission is in gear (or "PARK" if
9
automatic).
Ensure minimum distance of 0.5m between vehicle and static objects such as doors, walls, etc. to allow for
9
vehicle tilting.
Ensure all non-essential persons keep a safe distance whilst the jack is in use.
9
Ensure there are no passengers in the vehicle.
9
It is necessary that the operator can watch the lifting device and the load during all movements.
9
Place jack under only those lifting points recommended by vehicle manufacturer (see vehicle handbook).
9
Check that the lifting point is stable and centred on the jack saddle.
9
Ensure the jack wheels are free to move and that there are no obstructions.
9
▲ DANGER: Use the jack for lifting only, NOT for supporting the lifted load.
Ensure there are no persons or obstructions beneath the vehicle before lowering.
9
It is not allowed to work under the raised load until it is secured by suitable means. Use suitable axle stands under
9
the vehicle before proceeding with any task.
Use a qualified person to lubricate and maintain the jack.
9
Ensure that only hydraulic jack oil is used in the jack.
9
DO NOT operate the jack if damaged.
8
DO NOT allow untrained persons to operate the jack.
8
DO NOT operate the jack when tired or under the influence of drugs, alcohol or intoxicating medication.
8
DO NOT exceed the rated capacity of the jack.
8
DO NOT allow the vehicle to move during lifting or lowering, or use the jack to move the vehicle.
8
DO NOT jack vehicle if there is a risk of spillage of fuel, battery acid, or other dangerous substances.
8
DO NOT work under the vehicle until appropriately rated axle stands have been correctly positioned.
8
DO NOT use the jack for purposes other than that for which it is intended.
8
DO NOT top up hydraulic system with brake fluid. Use hydraulic jack oil only. (Sealey Part No: HJO500MLS or HJO5LS)
8
DO NOT adjust the safety overload valve.
8
When not in use store jack, fully lowered, in a safe, dry, childproof area.
9
If more than 400N of effort is generated in lifting, the efforts shall be lowered by an additional person.
9
2. INTRODUCTION
Made primarily for the motor racing enthusiast, this jack weighs in at just 17.6kg. Utilises many weight saving techniques such as
a skeletal lift arm. Features Rocket Lift by use of twin pistons, bringing saddle to maximum height in minimal pumps. Polyurethane
wheels for smooth and quiet manoeuvring, which also limits damage to garage floors. Lifting bars are fitted either side of the anodised
aluminium chassis enabling fast, lightweight pick-up.
3. SPECIFICATION
Model No:.................................................... RJA1800.V4
Applicable Standards: ............... EN 1494:2000+A1:2008
Capacity: ......................................................... 1.8 Tonne
Consumable Parts:..........................................................
Replacement Rubber Jack Pad - JP12
© Jack Sealey Limited
1.8 TONNE ALUMINIUM LOW PROFILE
TROLLEY JACK WITH ROCKET LIFT
RJA1800.V4
MODEL NO:
Original Language Version
Length: ................................................................ 637mm
Maximum Chassis Height: .................................. 155mm
Maximum Saddle Height: .................................... 425mm
Minimum Saddle Height: ....................................... 85mm
RJA1800.V4
TJL3
Apply
h ndbr ke
1 3 5
2 4 R
Use on h rd level floor
Chock
wheels
Never
exceed
j ck c p city
Close
Lower
R ise
OR
Lift & twist
to lower
R ise
Use suit ble xle st nds
X2
w w w . s e l e y. c o . u k
Issue 5 (ALL) 17/07/23