Related Manuals for ABB Tina 1A
Summary of Contents for ABB Tina 1A
- Page 1 Original instructions Tina 1A Blanking plug ABB AB / Jokab Safety Varlabergsvägen 11, SE-434 39 Kungsbacka, Sweden www.abb.com/lowvoltage...
- Page 2 DAMAGES, LOSS OF PROFITS OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY. In no event shall responsibility of ABB/JOKAB SAFETY for any act exceed the individual price of the product on which liability asserted.
-
Page 3: Table Of Contents
Installation precautions ............................8 Maintenance ..............................8 Testing of the safety functions ..........................8 Troubleshooting ..............................8 Operation ............................. 9 LED indication..............................9 Technical data ........................... 10 Dimensions ..............................11 EC Declaration of conformity ......................12 2TLC172117M0201, rev. A www.abb.com/lowvoltage 2011-09-19... -
Page 4: Introduction
Introduction Scope The purpose of these instructions is to describe the blanking plug Tina 1A and to provide the necessary information required for installation and operation. Audience This document is intended for authorized installation personnel. Prerequisites It is assumed that the reader of this document has knowledge of the following: Basic knowledge of ABB/Jokab Safety products. -
Page 5: Overview
Overview General description Tina 1A is a unit intended for use with connection blocks Tina 4A or Tina 8A, where Tina 1A is used as a blanking plug in unused M12 connections. The Tina 1A blanking plug is intended for use in safety circuits in accordance with EN 60204-1. -
Page 6: Connections
Dynamic signal input 3 ) Blue: 0 VDC 4 ) Black: Dynamic signal output 5 ) Grey: Not used Caution! All cable colours according to ABB/Jokab Safety standard cables. Accessories for connection to the safety circuit Type Article number Description M12-C112 2TLA020056R2000 1 m cable, 5-pole, 0.34 mm... -
Page 7: Connection Examples
Connection examples Caution! All cable colours according to ABB/Jokab Safety standard cables. 2TLC172117M0201, rev. A www.abb.com/lowvoltage 2011-09-19... -
Page 8: Installation And Maintenance
The unit needs to be replaced. Contact The unit is defect same time ABB/Jokab Safety. NB: Another Tina 1A can be used instead of this unit to check if the safety circuit is OK (only for test). 2TLC172117M0201, rev. A www.abb.com/lowvoltage 2011-09-19... -
Page 9: Operation
Description Input signal on pin-2 Green Safety circuit closed (protection OK) Dynamic signal in LED on Tina Green-Red (flash) Safety circuit open (protection OK) No dynamic signal in or 0 VDC in +24 VDC in 2TLC172117M0201, rev. A www.abb.com/lowvoltage 2011-09-19... -
Page 10: Technical Data
Technical data Manufacturer Address ABB AB / JOKAB SAFETY Varlabergsvägen 11 SE-434 39 Kungsbacka Sweden Article number/Ordering data Tina 1A: 2TLA020054R0000 Power supply Operating voltage 24 VDC +15 %, -25 % Total current consumption 17 mA (27 mA with max information output) -
Page 11: Dimensions
Dimensions NB: All measurements in millimetres. 2TLC172117M0201, rev. A www.abb.com/lowvoltage 2011-09-19... -
Page 12: Ec Declaration Of Conformity
EC Declaration of conformity EC Declaration of conformity (according to 2006/42/EC, Annex2A) ABB AB declare that the safety components of ABB AB make with type designations and safety JOKAB SAFETY functions as listed below, is in conformity with the Directives Varlabergsvägen 11...