Sealey LED1R Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
instructions
1. SAFETY
1.1. ELECTRICAL SAFETY
WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following: You must check
‰
all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other connectors for
wear or damage.
1.1.1. Ensure that cables are always protected against short circuit and overload.
1.1.2. Regularly inspect power supply cables check all connections to ensure that none are loose.
IMPORTANT: Ensure that the voltage marked on the appliance matches the power supply to be used and that the circuit is fitted with the
correct fuse. If in doubt, consult a qualified technician to connect the floodlight to a fused and switched DC supply.
DO NOT pull or carry the floodlight by the power cable.
8
DO NOT use worn or damaged cables, plugs or connectors.
8
Immediately have any faulty item repaired or replaced by a qualified technician.
9
2. INTRODUCTION
MODEL NO. LED1R
4 x 3W Epistar™ high power LEDs. Produces up to 960 lumens output. Operating voltage of 10-30V DC. Waterproof rating of IP68.
ECE R10 Certified and E-Marked. Suitable replacement for traditional halogen work lights. Powder coated die-cast aluminium housing.
Adjustable grade 201 shock-resistant stainless steel bracket.
MODEL NO. LED3R
9 x 3W Epistar™ high power LEDs. Produces up to 2160 lumens output. Operating voltage of 10-30V DC. Waterproof rating of
IP68. ECE R10 Certified and E-Marked. Suitable replacement for traditional halogen work lights. Powder coated die-cast aluminium
housing. Adjustable grade 201 shock-resistant stainless steel bracket.
MODEL NO. LED3RM
9 x 3W Epistar™ high power LEDs. Produces up to 2160 lumens output. Operating voltage of 10-30V DC. Waterproof rating of
IP68. ECE R10 Certified and E-Marked. Suitable replacement for traditional halogen worklights. Powder coated die-cast aluminium
housing. Adjustable grade 304 shock-resistant stainless steel bracket. Supplied with a magnetic base, coiled cable and vehicle
accessory socket plug.
MODEL NO. LED4R
14 x 3w Epistar™ high power LEDs. produces up to 3360 lumens output. Operating voltage of 10-30V DC. Waterproof rating of IP68.
ECE R10 Certified and E-marked. Suitable replacement for traditional halogen work lights. Powder coated die-cast aluminium
housing. Adjustable grade 201 shock-resistant stainless steel bracket.
3. SPECIFICATION
MODEL NO:.................LED1R....................................LED3R.....................................LED3RM..........................LED4R
Lumen Output: ...............960lm.......................................2160lm......................................2160lm...............................3360lm
Power:...........................12W..........................................27W...........................................27W....................................42W
Supply: ......................... 10-30VDC................................10-30V DC.................................10-30V DC.........................10-30V DC
Size (W x H):................ Ø80mm....................................Ø115mm....................................Ø115mm.............................Ø115mm
© Jack Sealey Limited
12W - 42W ROUND LED VEHICLE MOUNTED
WORK LIGHTS
MODEL NO:
LED1R
Original Language Version
LED1R, LED3R, LED3RM, LED4R
LED3R
LED1R, LED3R, LED3, LED4R Issue 2 (2,3) 11/04/23
LED3RM
LED4R