Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Husqvarna 325iR
Summary of Contents for Husqvarna 325iR
- Page 1 325iR Operator's manual 2-25...
-
Page 2: Table Of Contents
Contents Introduction..............2 Transportation, storage and disposal......21 Safety................5 Technical data.............. 22 Assembly..............13 Accessories..............23 Operation..............16 Declaration of Conformity..........24 Maintenance..............19 Appendix ..............26 Troubleshooting............21 Introduction Product description Note: National or local regulations can set limit to the operation of the product. - Page 3 Product overview 1. Operator's manual 14. Suspension point 2. Bevel gear 15. User interface 3. Hole for locking pin 16. Power unit 4. Trimmer head 17. Charger cable 5. Cutting attachment guard 18. Battery charger 6. Combination wrench 19. Power on and Warning indicator (LED) 7.
- Page 4 27. Support flange 28. Locknut 29. Transport cover Beware of blade thrust. 30. Drive disc 31. Harness Symbols on the product or its packaging Symbols on the product indicate that this product cannot be handled as domestic waste. This product WARNING! This product can be must be deposited at an appropriate dangerous! Careless or incorrect use...
-
Page 5: Safety
Product liability • the product has an accessory that is not from the manufacturer or not approved by the manufacturer. As referred to in the product liability laws, we are not • the product is not repaired at an approved service liable for damages that our product causes if: center or by an approved authority. - Page 6 • Dress properly. Do not wear loose clothing or • Use power tools only with specifically designated jewellery. Keep your hair and clothing away from battery packs. Use of any other battery packs may moving parts. Loose clothes, jewellery or long hair create a risk of injury and fire.
- Page 7 • The rated rotational speed of the cutter must be at • Maintain control of the machine and do not touch least equal to the maximum rotational speed marked cutters, lines or blades and other hazardous moving on the machine. Cutters running faster than their parts while they are still in motion.
- Page 8 • Check that the trimmer head and trimmer guard are and qualified specialists. See instructions under the not damaged or cracked. Replace the trimmer head Maintenance heading. or trimmer guard if it has been exposed to impact • Working in bad weather is tiring and often brings or are cracked.
- Page 9 • If any unwanted vibrations occur, tap out new line to • Always use approved protective googles that comply give the line the correct length to stop the vibrations. with ANSI Z87.1 standard in the USA or EN 166 in EU countries.Use visor for face protection.
- Page 10 1. Make sure that the power trigger is locked when the CAUTION: All servicing and repair work lock is in its initial position. on the machine requires special training. This is especially true of the machine′s safety equipment. If your machine fails any of the checks described below you must contact your service agent.
- Page 11 • The harness release function is at the front of the product. • The harness straps must always stay at the correct position. • To attach, tighten the locknut in the opposite • In an emergency, the harness release function helps direction to the direction of rotation of the cutting you to safely release from the product.
- Page 12 • When you use a grass blade, make sure that the correct blade guard and the harness are attached to the product. • A defective or incorrect guard can cause injury. Do not use a cutting attachment that does not have an approved guard attached.
-
Page 13: Assembly
Assembly To assemble the handlebar 2. Turn the handlebar until it is parallel to the shaft. 1. Remove the screw behind the throttle handle. 2. Move the throttle handle to the right side of the handlebar. 3. Turn the handlebar around the shaft until the 3. - Page 14 4. Turn the trimmer head (H) counterclockwise to WARNING: Always use the cutting attach. attachment guard that is recommended for Accessories on the cutting attachment. See page 23 . WARNING: An incorrectly attached cutting attachment can result in injury or death.
- Page 15 To remove the cutting attachment guard 7. Tighten the nut with the socket wrench. Hold the shaft of the socket wrench near the blade guard. • Loosen the bolt (C) and remove the cutting Tighten in the opposite direction to how the cutting attachment guard (A) from the shaft.
-
Page 16: Operation
Read and understand the safety chapter before you use the product. To connect the battery to the product WARNING: Only use Husqvarna original batteries with the product. 1. Make sure that the battery is fully charged. CAUTION: If the battery does not move easily into the battery holder, the battery is not installed correctly. - Page 17 • Do an overhaul of the product. 1. Push the mode button to set a limit to the maximum speed. The white LEDs comes on to show that the • Do the safety inspections, maintenance and service function is on. that are given in this manual.
- Page 18 Grass trimming with a trimmer head 4. Use full speed when you move the product from side to side to cut grass. To trim the grass 1. Hold the trimmer head immediately above the ground at an angle. Do not push the grass trimmer line into the grass. 2.
-
Page 19: Maintenance
3. Push the release buttons on the battery and pull the battery out. Maintenance Introduction Maintenance schedule WARNING: Before you do any WARNING: Remove the battery before maintenance work you must read and you do maintenance. understand the safety chapter. The following is a list of the maintenance steps that you must do on the product. - Page 20 Make sure that the bevel gear is filled correctly with grease, see bevel gear on page 20 . If not, use Husqvarna bevel gear grease. Make sure that the air intake of the motor is not dirty. Clean the air intake with compressed air.
-
Page 21: Troubleshooting
6. Install the grease plug. Troubleshooting User interface Problem Possible faults Possible action Battery LED indicator flashes or- Low battery voltage. Charge the battery. ange Error LED flashes red Overload. The cutting attachment is jammed. Deacti- vate the product. Remove the battery. Clean the cutting attachment from unwanted mate- rials. -
Page 22: Technical Data
Technical data Technical data 325iR Motor Motor type Husqvarna e-torq BLDC Speed of output shaft. Trimmer head/blade, 1/min 5800 Cutting width, mm Weight Weight without battery, harness and cutting attachment, kg Noise emissions Sound power level, measured dB (A) Sound power level, guaranteed L... -
Page 23: Accessories
Battery BLi 200 Nominal voltage, V Weight, kg (lb) 1.3 (2.9) Approved battery chargers Battery charger QC330 Input voltage, V 100-240 Frequency, Hz 50-60 Power, W Accessories Accessories Approved accessories Accessory type Cutting attachment guard, art. no. Centre hole in blades/knives, Ø 25.4 mm Output shaft thread M10 Multi 255-3 (Ø... -
Page 24: Declaration Of Conformity
Declaration of Conformity EU Declaration of conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Battery-operated brushcutter / grass trimmer Brand Husqvarna Type / Model 325iR Identification Serial numbers dating from 2023 and onwards... - Page 25 UK Declaration of conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Battery-operated brushcutter / grass trimmer Brand Husqvarna Type / Model 325iR Identification Serial numbers dating from 2023 and onwards...
-
Page 26: Appendix
T35, T35x Li-ion 8,5 m 10 cm 4" 4,3 m "Click" 15 cm 6" 1859 - 004 - 02.06.2023... - Page 27 1859 - 004 - 02.06.2023...
- Page 28 Original instructions 1143023-26 2023-06-08...