Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Sharp Manuals
  4. Racks & Stands
  5. MP300CM
  6. Installation and assembly manual

Sharp MP300CM Installation And Assembly Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
Installation and Assembly Manual:
Ceiling Mount for NP-PE506WL, NP-PE506UL, NP-PE456USL,
NP-MC453X, NP-MC423W, NP-ME453X, NP-ME423W, NP-ME403U,
NP-P474W, NP-P474U, NP-P554W, NP-P554U Projectors
Model: MP300CM
Features:
• ImageLock
alignment prevents picture sag or drift
TM
• Wrench access slot for easier flush mount installations
• Exclusive aluminum track quick release
Max UL Load Capacity: 50 lb (22.7 kg)
1 of 9
ISSUED: 2010-01-10
SHEET #: 056-9034-9
(2023-04-20)
For customer care call 1-800-865-2112
Visit the Peerless Web Site at www.peerlessmounts.com

Advertisement

loading

Related Manuals for Sharp MP300CM

Summary of Contents for Sharp MP300CM

  • Page 1 Installation and Assembly Manual: Ceiling Mount for NP-PE506WL, NP-PE506UL, NP-PE456USL, NP-MC453X, NP-MC423W, NP-ME453X, NP-ME423W, NP-ME403U, NP-P474W, NP-P474U, NP-P554W, NP-P554U Projectors Model: MP300CM Features: • ImageLock alignment prevents picture sag or drift • Wrench access slot for easier flush mount installations • Exclusive aluminum track quick release Max UL Load Capacity: 50 lb (22.7 kg)

  • Page 2: Table Of Contents

    NOTE: Read entire instruction sheet before you start installation and assembly. WARNING • Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call Peerless customer care at 1-800-865-2112.

  • Page 3: Parts List

    Before you start check the parts list to insure all of the parts shown are included. Parts List Description Qty. Part # 054-2171 projector mount assembly 4 mm security allen wrench 560-9646 520-2151 #10-32 x 3/8" serrated washer head socket pin screw #10-32 x 1/4" socket pin screw 520-2196 540-1078 flat washer #14 x 2.5 phillips hex head wood screw 5S1-015-C04 concrete anchor 590-0320...

  • Page 4: Installation To Extension Columns / Ceiling Plate

    Installation to Extension Column / Ceiling Plate NOTE: Refer to accompanying instructions with ceiling plates (sold separately) for installing these models to ceiling. Screw projector mount assembly (A) onto extension column as shown in figure 1.1. Tighten swivel stop screw against extension column, flush mount tube or reducer using 4 mm security allen wrench (B) as shown in figure 1.2.

  • Page 5: Installation To Wood Joist Ceilings

    Installation To Wood Joist Ceilings WARNING • Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. • Tighten wood screws so that projector mount assembly is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power. •...

  • Page 6: Installation To Concrete Ceilings

    Installation to Concrete Ceilings WARNING • When installing Peerless ceiling mounts on a concrete ceiling, the ceiling must be at least 8" thick with a minimum compressive strength of 2000 psi. Never attach concrete expansion anchors to concrete covered with plaster, drywall, or other finishing material. • Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.

  • Page 7: Attaching Adapter Plate To Projector

    Attaching Adapter Plate to Projector Align shoulder on connection block (EE) opposite notch in adapter plate (AA). Attach adapter plate (AA) to connection block (EE) using two #10-32 x 3/8" serrated washer head socket pin screws (C) SHOULDER as shown in figure 4.1. Tighten screws using 4 mm allen wrench (B). NOTCH INDICATES FRONT OF PROJECTOR fig. 4.1 Flip projector upside down and attach adapter plate (AA) using four serrated socket pin screws (BB) and retaining spacers (CC) as shown below.

  • Page 8: Attaching Adapter Plate To Projector Mount

    Attaching Adapter Plate to Projector Mount WARNING • Do not lift more weight than you can handle. Use additional man power or mechanical lifting equipment to safely handle placement of the screen. Slide connection block (EE) with projector into projector mount assembly (A) as shown. Tighten captive screw to secure projector to projector mount assembly (A).

  • Page 9: Projector Alignment

    Projector Alignment To adjust yaw (swivel) for wood stud and concrete ceiling: Loosen wood screws (F) if flush mounted to wood joists (page 5) or concrete ceilings (page 6), until projector mount can be rotated. Rotate mount to desired position and retighten screws. To adjust yaw (swivel) for extension column applications: Loosen screw on projector mount assembly (A) indicated below until projector mount can be rotated.