Advertisement
Rx = nnnn
Data (DCE Rate) T/D?
Tx = mmmm
Pressing
at this
display toggles modem
between talk/data
states
TEST OPT'S
AT&L
MODULATION OPT'S
Line=Dial (1,2,3,4d)
:2W Lease (4L)
:4W Lease
AT
RE
*
RESTORAL OPT'S
Restore=Off (1,2,3,4d)
:FP Only
:FP/108.1
:FP/116
:FP/Auto (4L)
:FP/108.ACU
:FP/116.ACU
Note:
When you select Modulation Mode
(AT*MM), you must ensure that the
Max Rate (AT*MX) and Min Rate
(AT*MR) parameter options are within
the valid range for the mode.
Figure A-1. The 326X Series Modem Menu Structure - Part 1 of 4
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
ATI
AT&V
AT&V
AT
ST
AT
ST
ATZ
*
*
DTE (Rate) EC Mode
PhaseJitter=0dg
Select Options=1
Frq Offset=0Hz
EC=(Mode)DC=(Mode)
Tx
Kb
0%
Tx Level=0dbm
Rx Level=-0dbm
Rx
Kb
0%
Retrains 0
DCD RTS CTS
Echo Delay=0ms
DSR DTR
Far Echo Lvl=0
AOP DLP ALP
DR=0 TI=0 O D
Nr Echo Lvl=0
Phase Roll=0
Display Modem ID
Eqlzr SNR=0dB
(s/w rev lvl)
SQ=0
EP=0%
AT
MM
AT
AY
AT
LS
*
*
*
Auto Type=CCITT (A)
Low Speed=Bell
Mod=V.34 Auto (A,F)
:CCITT
:Codex
:V.34 Only
:V32bis Auto (A,S)
:Auto V32
:V32bis Only
:V32 Only
:V32 Uncoded
:V22bis Only
:212 Only
:103 Only
:V21 Only
AT
AP
AT
CA
*
*
AdaptiveRate=On (A)
Mode=Originate (1,3)
:Off
:Answer (2,4)
:External
:Auto A in O
AT
DI
AT
LE
*
*
LtoD=Low/Fast (A)
D to L=Manual (1,2,3,4d)
Hold Dialine=Off (A)
:Low/Slow
:15 min
:High/Fast
:30 min
:High/Slow
:1 hour
:2 hour
:4 hour
AT&W
AT&Y
Save Changes=1
Power Up In=Old (D)
Reinit Memory?
:2
:2
:1
:3
:3
:2
:4
:4
:3
:4
AT&Z
AT
CN
AT
LN
*
*
Enter Phone#=1
Link Phone#=1
:n
:n
:9
:9
AT&T
ATH
AT&T
ATO
TEST=End Test
Accept RDL=On
LAL Busy Out=On
:Off
:LAL
:RDL
:LDL
:Pattern
:LAL Pat
:RDL Pat
:Busy Out
:Retrain
AT
MX
AT
MN
*
*
Max Rate=14.4(S)/28.8† (A,F)
Min Rate=300 (A)
:1200
:33.6
:1200
:2400
:31.2
:300
:4800
:26.4†
:7200
:24.0†
:9600 (2,3,4L SDC)
:21.6†
:12.0
:19.2†
:14.4
:16.8†
:16.8†
:14.4 (A,S)
:19.2†
:12.0
:21.6†
:9600
:24.0†
:7200
:4800
:2400
AT&X
AT
RT
*
Clock=Internal (A)
Retrain=High BER
Longspace=Off (A)
:Off
:External (2 SDC)
:Low BER
:Loopback
AT
HD
AT
AS
*
*
Ans Rest=LL Fail (A)
:1 min
:Always
:2 min
:3 min
:4 min
KEY
:5 min (4L SDC)
=
Option Included
in Option Sets
=
(A)
Default for All Option Sets
=
(D)
Default for Options Not Included in Option Sets
=
(1-4)
Default for Option Set n (n=1-4)
=
(L)
Option Set Default for 3261, 3263, 3266, 3268 Modems
=
(d)
Option Set Default for 3260, 3262, 3265, 3267 Modems
=
(S)
Default for 326X V.32bis Modem
=
(F)
Default for 326XFAST Modem
=
(†)
Available with 326XFAST Only
(SDC) = Sync Data Compression (available for 326XFAST-SDC only)
For example, in the Min Rate (AT
:9600 (2,3,4L SDC) means 9600 is the default for option sets
2, 3 and 4L (models 3261FAST, 3263FAST, 3266FAST
and 3268FAST) with the Sync Data Compression product.
Otherwise, the default is 300 bps for all option sets.
Configuration Quick Reference A-3
ATDS
AT&F
AT
DS
AT
ND
*
*
Dial From#=1
View Phone#=1
:n
:n
:9
:9
ATD
AT
DR
ATS
*
Enter Then Dial
Auto Redial=Off (D)
S-Reg nnn=xxx
:1
:n
:15
AT
LL
*
:Off
AT
AR
AT
FC
*
*
V.34 Asym=On
Fast Call=Off (A)
:26.4†
:Off
:Lvl1
:28.8†
:Lvl2
:31.2
:Lv i3 (2,3,4L SDC)
:33.6
ATY
AT
MD
AT&G
*
Guard Tone=Off
PSTN=On (A)
:550
:Off
:On
:1800
=
Country Specific
Option
*
MN) option,
Advertisement
Chapters
Troubleshooting
