Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Beko DDT25400B
Summary of Contents for Beko DDT25400B
- Page 1 Dishwasher Installation Manual DDT25400B DIT25400 DDT25400GB DIT28430 DDT25400W DIT29430 DDT25400X DUT25400B DDT25400XP DUT25400W DDT28410X DUT25400X DDT28430X DUT28430W DDT28430XP DUT28430X DDT29430X Document Number : 15 0625 0100_AA_USA/ 02-03-16.(10:36)
-
Page 2: Table Of Contents
To prevent accidents, which could cause serious injury or death, as well as machine damage read these instructions before installation and / or use. INTRODUCTION 1. IMPORTANT SAFETY INSTRUCTIONS 1.1 INSPECT THE DISHWASHER 2. TOOLS WHICH MAY BE NEEDED 3. MATERIALS WHICH MAY BE NEEDED 4. -
Page 3: Introduction
INTRODUCTION NOTICE : Please read this installation manual Read these installation instructions and particularly the safety instructions completely before installing and follow completely and carefully. They will save you them carefully. Save these installation time and effort and help to ensure optimum instructions and pass them on to any dishwasher performance. -
Page 4: Inspect The Dishwasher
If the dishwasher is installed in a NOTICE : • location that experiences freezing The dishwasher drain hose must be • temperatures (e.g. in a vacation home, installed with a drain loop at least cabin, etc.), you must drain all the 28”... -
Page 5: Tools Which May Be Needed
2. TOOLS WHICH MAY BE NEEDED 3. MATERIALS WHICH MAY BE NEEDED (Additional materials may be required to comply with local codes) Hot Water Supply Line - Minimum 3/8” O.D. copper tubing or metal braided dishwasher supply line. 90° elbow with 3/8” N.P.T. male threads on one leg, and sized to fit your water supply line (copper tubing/compression fitting, or braided hose) on the other leg. -
Page 6: Materials Supplied
4. MATERIALS SUPPLIED 4.1 PARTS SUPPLIED 4.4 DISHWASHER PARTS BAG 2 Parts for your dishwasher will come in several plastic bags. (MODEL DEPENDING) Check your parts bags shown In addition to the manual bag to make sure you have all the and the dishwasher parts bag parts as listed to the left. -
Page 7: Dishwasher Specifications
5. DISHWASHER SPECIFICATIONS 2 4 ” ( 6 1 2 4 ” ( 6 1 ” m 5.1 TECHNICAL FEATURES 14 place settings Load capacity Permissible water 4.35 - 145 psi (0.3 - 10 bars) pressure 120 V (volts), 12 A (amps), 60Hz (hertz) Electrical connection 1400 W (watts) Total power... -
Page 8: Enclosure Preparation
6. ENCLOSURE PREPARATION 6.1 ELECTRICAL PREPARATION WARNING The dishwasher is designed for an electrical supply of 120 V, 60 Hz, AC, connected to a dishwasher-dedicated, properly grounded electrical circuit with a fuse or breaker rated for 15 amperes. 6.2 PREPARATION FOR INSTALLING MOUNTING BRACKETS WARNING... -
Page 9: Adjusting Height
6.3 ADJUSTING HEIGHT If the height of the enclosure is 337/8” to 357/8” (861 mm - 911mm) adjust supports as shown in the figure. Supplied (4) Adjust the front foot level with the adjusting wrench to balance and raise the dishwasher to the enclosure height. -
Page 10: Preparing The Water Connection (A)
6.5 PREPARING THE WATER CONNECTION (A) Install an easily accessible shut-off valve (not supplied) in the water supply line. All solder connections must be made before the water line is connected to the dishwasher’s water inlet valve. Water can also be supplied to the dishwasher by using a flexible braided hose line. -
Page 11: Drain Preparation
6.6 DRAIN PREPARATION The dishwasher drain hose may be connected to the drain plumbing in one of three ways (Figure A, B, C). NOTICE : • Either one of the above methods must be used or the dishwasher will not operate properly. -
Page 12: Steam Protection Foil
6.7 STEAM PROTECTION FOIL Steam will form inside the dishwasher during operation. At the end of the cycle, when the dishwasher door is opened, it is required to use a steam protection foil to prevent any steam from collecting on the underside of the counter top. 6.6.2 FITTING THE PROTECTION FOIL Before applying the steam protection foil to the underside of the countertop, clean the area with... -
Page 13: Placement Of Dishwasher Into The Opening
7. PLACEMENT OF DISHWASHER INTO THE OPENING Now place the dishwasher into the opening and get ready to connect all hoses and electrical connections. CAUTION Make sure all hoses are pulled through the side opening of the cabinet, no hoses are kinked and all slack is taken out as shown in the above figure. - Page 14 7.1.2 PREPERATION OF WATER SUPPLY Left side water supply connection Before pushing the dishwasher in to the cabinet you must place water supply hoses into the channel of the dishwasher (Figure A). Place the supplied clips into the channel (Figure B) so that you can move these clips along the channel (Figure C) and fix by pressing on (Figure D) so that you can keep the water supply hose in the...
- Page 15 After installing one clip for each side push the dishwasher into the cabinet (Figure E). Note that while pushing the dishwasher into the cabinet, water supply hose must move in the channel to the front (Figure F). Fix the second clip (Figure G).
- Page 16 7.1.4 ELECTRICAL CONNECTION WARNING Make sure the voltage and frequency • listed on the data plate correspond with the household electrical supply. This data must correspond to prevent injury and machine damage. Consult a qualified electrician if in doubt. Only connect the dishwasher to •...
- Page 17 with all local codes and ordinances. This appliance must be connected to a grounded metal, permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the appliance. WARNING Improper connection of the equipment- grounding conductor can result in a risk...
-
Page 18: Readjusting Foot Levels
7.2 READJUSTING FOOT LEVELS (3,5mm) Ø " Now that the dishwasher is in the cabinet you must readjust the feet to (3,5mm) Ø " bring the dishwasher up to the required height and attach it underneath the countertop. 1. Readjust the front foot levels with adjusting wrench to balance the dishwasher and raise it up under the countertop, make sure the unit is level. -
Page 19: Installing The Outer Door
3. Now attach the toe kick to the bracket with the two (Ø 3/16” x 1/4” - Ø 4mm x 6mm) screws and the caps provided as follows. If the enclosure height is below 331/16” (840mm) use only “o” labelled toe kick (toe kick without slots). - Page 20 1. Prepare the wooden door with the mounting brackets. Height : Height of the wooden door 30” (760mm) Width : 23 ¼” to 23 ½” (592mm - 595mm) Thickness : ¾ “ (19mm) 2. To take the plastic bracket out, remove the screws on it.
- Page 21 5. Attach the two mounting brackets to the wooden door with 4 screws (Ø 1/8” x 5/8” (Ø 3.5mm x 14mm) (3,5mm) Ø " (Figure A). 6. Mount the wooden door onto the dishwasher with the plastic mounting brackets which you have attached (Figure B).
- Page 22 8. Using the four screws Ø 3/16” x 111/16” (Ø 4mm x 43mm) provided, attach the wooden door to the dishwasher at position 1 and 4 (Figure A). Ø 3 / 16 " (4mm) 9. Check the position of the wooden door and make sure it is aligned properly (Figure B).
- Page 23 11. Check whether the bottom of the door hits the toe kick of the kitchen cabinet (A). 11.1. If the door hits the toe kick cut the necessary section out of the toe kick (B). 11.2. Apply silicon or sealant to the cut edge of the kitchen cabinet toe kick or paint so it does not absorb moisture.
- Page 24 NOTICE : If you have a European kitchen or want to install a wooden toe kick to match your kitchen, please refer to one of the two drawings given below. Follow the same instructions on the brackets as for the removable toe kick. Installation should be done following the steps illustrated in the figures A, B, C, D respectively.
-
Page 25: Installer Checklist
8. INSTALLER CHECKLIST NOTICE : Your installer must have completed and If the dishwasher does not operate checked the following: properly, refer to the self help hints. The dishwasher is square and level. • The dishwasher is fastened securely • 10.