Sharp XE-A402 Quick Start Manual

XE-A402 Quick Start Guide
The following describes how to get the cash register ready for operation. Follow these steps before using the cash register for the first time.
Place the cash register on a stable, flat surface not subject to direct sunlight.
1 Connecting the

Barcode Scanner

A barcode scanner is provided with the cash
register. To use the scanner, connect the scanner
before turning on the register.
1. Open the Serial/Scanner port cover at the right
side of the register.
2. Insert the connector of the
barcode scanner into the
Serial/Scanner port, and
tighten both of screws on
the connector.
CAUTION:
• Always unplug the power cord of the cash
register when you connect or disconnect the
barcode scanner.
• Never connect devices other than the barcode
scanner before changing the interface setting.
Otherwise malfunction of the cash register will
occur.
Initializing the Cash
2
Register
To ensure the cash register operates properly,
please use the following procedure:
1. Make sure the power cord plug is not inserted
into the AC outlet.
2. Insert the manager
REG
(MA) key into the mode
OPX/Z MGR
OFF
switch and turn it X1/Z1
X2/Z2
VOID
to the PGM
PGM
position.
3. While holding down both the
} l
key and the key, insert
the plug into the AC outlet.
The buzzer will sound three
times and " MRS. " will
*** ***
be displayed.
4. The cash register has now been initialized.
The register display will show "0.00" with
"PGM".
CAUTION: To charge the rechargeable batteries,
keep the power on for one or two
days. Leave the register with the
mode switch in a position other than
"OFF".
NOTE: If you press a key by mistake, an error
message may be displayed. Press the
l
key to clear message after installing
paper rolls.
Preparing the Cash Register
3
1. Push the printer cover forward and detach it.
2. Remove the white retainer at the position
shown in the illustration at the right.
NOTE: Please keep this retainer for future use
when transferring the cash register.
3. Move the print head release lever upwards as
shown in the illustration at the right.
4 Installing the Paper Rolls
1. Cut off approximately one revolution of each
paper roll.
Make sure the paper end is cut as shown in
the illustration at the right.
For receipt paper installation
2. Set a paper roll in the paper cradle of
To the printer
the receipt side (left side) as shown in
the illustration at the right.
Correct
3. Insert the end of the paper into the paper chute
until it is caught by the printer auto-feed and
comes out the top of the printer. If the printer
does not catch the paper, feed the paper while
{
pressing .
4. Cut off the excess paper with the paper cutter.
For journal paper installation
5. Set a paper roll in the paper cradle of the journal side as illustrated in step 2.
6. Insert the end of the paper into the paper chute until it is caught by the printer
auto-feed and comes out the top of the printer. If the printer does not catch the
}
paper, feed the paper while pressing .
7. Insert the end of the paper into the slit in the take-
up spool and wind the paper two or three turns
}
around the spool shaft. (Press to feed more
paper if required.)
}
8. Set the spool on the bearing, and press the
key to take up excess slack in the paper.
9. Replace the printer cover.
5 Basic Programming
Set the mode switch to the PGM
position.
Setting the Date
Enter the date in 8 digits using the month-day-year format.
s
Then press
Retainer
Example:
08262004 s
Date (August 26, 2004)
Setting the Time
Print head
Enter the time in 4 digits ("hhmm" format) using the 24 hour
release lever
system. Then press
Example:
1430 s
Time (2:30 p.m.)
Setting Tax Rates (%)
NOTE: If you are in an area that uses a tax table for tax
calculation, please refer to the programming section
in the instruction manual.
Specify a tax rate (%) for calculation of tax on each taxable
Correct Incorrect
subtotal using the following sequence:
s 9
➔
To the printer
@
R ➔ ➔ Q ➔
Incorrect
where
R: Tax rate (0.0000% to 100.0000%)
Q: Minimum taxable amount (0.01 to 999.99)
(Smallest amount for which tax must be collected.)
*Up to 4 types of tax are programmable.
Example:
s 9@
1@ 6P25@ 12 s A
Tax 1 Tax rate (6.25%)
Other Programming
The cash register is pre-programmed so it can be used with
minimal set-up. For optional features, please refer to the
instruction manual.
Initial settings:
Department 1 to 10:
Department 11 to 99: Non-taxable.
NOTE: For scan barcodes using the barcode scanner, their
preset unit prices, associated departments and item
labels should be programmed.
6
Before Starting Entries
REG
OPX/Z MGR
• Set the mode switch to
OFF
X1/Z1
X2/Z2
VOID
PGM
.
1. Enter the price for the first department item.
s
.
2. Repeat step 1 for all the department items.
3. Press
4. Enter the amount received from the customer.
5. Press
@ @ 6. Tear off the receipt and give it to the customer
➔ ➔ Tax number (1 to 4)* ➔ ➔
s A
➔
7. Close the drawer.
NOTE: When you scan a barcode using the
Min. taxable
amount ($0.12)
When an error occurs:
Taxable 1
When an error occurs with an alarm sound, press
l
error, press
finalized in subtotal void or cash sale.
English
Now, you are ready!
REG
the REG position.
OPX/Z MGR
OFF
X1/Z1
VOID X2/Z2
PGM
5:
For example for 5.00, enter , and press
the appropriate department key.
For department 21 to department 40, press
D
first before pressing the department
key.
For department 41 and above, enter the
department number using numeric keys, and
d d
press , then enter the price and press
again.
s
to display the amount due.
(You can omit this step if the amount tendered
is the same as the subtotal.)
A
, and the change due is
displayed (when the amount received was not
entered, total amount is displayed) and the
drawer is opened.
with his or her change.
Key operation
5:¡ 825D™
Price and dept. 1 Price and dept. 22
s 2:0 A
Amount tendered
barcode scanner without programming,
the cash register goes into the learning
function mode. For details of this mode,
please refer to the instruction manual.
to clear the error. If you do not clear the
E
twice. The transaction will be
Printed in China
KS(TCADH2467RCZZ) 1