Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Honeywell TOUCHDOWN
Summary of Contents for Honeywell TOUCHDOWN
- Page 1 TOUCHDOWN 48” CEILING FAN MODEL #50205 Español p. 20 Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-877-361-3883, Monday - Thursday, 8 am - 6 pm, EST and Friday, 8 am - 5 pm, EST.
-
Page 2: Table Of Contents
WELCOME TABLE OF CONTENTS PREPARATION Before beginning the assembly of this product, ensure Care and Maintenance ......2 that all parts are present. -
Page 3: Package Contents
PACKAGE CONTENTS Unpack your fan and check the contents. You should have the following items: 1. Motor Housing 2. Light Kit 3. Socket Ring Tool 4. Blade Arm (5) 5. Canopy 6. Hanger Bracket 7. Canopy Cover 8. Optional Cap 9. -
Page 4: Safety Information
SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate, or install the product. • Before you begin installing the fan, disconnect the power by removing fuses or turning off the circuit breakers. • Make sure that all electrical connections comply with local codes, ordinances, the National Electrical Code, and ANSI/NFPA 70-199. -
Page 5: Mounting Options
MOUNTING OPTIONS DANGER Fig. 1 Turn off the circuit breakers and the wall switch to the fan supply line leads. Failure to disconnect the power supply prior to installation may result in serious injury or death. 1. Your fan has 3 mounting options: •... -
Page 6: Mounting Bracket Installation
MOUNTING BRACKET INSTALLATION 4. Loosen the four mounting bracket screws. Fig. 4 Completely remove the two mounting bracket screws and washers from the round holes in the Mounting Mounting canopy. Set aside for later use. Detach mounting Bracket Bracket Screws bracket from the canopy (Fig. -
Page 7: Standard Or Angle Mounting Instructions
STANDARD OR ANGLE MOUNTING INSTRUCTIONS 6. Partially loosen the two set screws in the yoke at Fig. 6 the top of the motor housing (Fig. 6). Set Screws Fig. 7 7. Remove the downrod pin and downrod clip from the downrod (Fig. 7). Downrod Clip Downrod Pin... - Page 8 STANDARD OR ANGLE MOUNTING INSTRUCTIONS 9. Slide the downrod into the yoke of the motor Fig. 9 Downrod housing, align the holes, and reinstall the downrod pin and downrod clip. Then retighten the set screws (Fig. 9). Downrod Downrod Clip Downrod Pin Set Screw Downrod Clip...
- Page 9 STANDARD OR ANGLE MOUNTING INSTRUCTIONS 12. Install the downrod ball into the mounting bracket Fig. 12 opening. Align the slot in the downrod ball with the tab in the mounting bracket. The downrod should not rotate if installed correctly (Fig. 12). Slot Mounting Bracket...
-
Page 10: Closemount Instructions
CLOSEMOUNT INSTRUCTIONS 13. Remove the canopy cover from the bottom of the Fig. 13 canopy (Fig. 13). Helpful Hint: The downrod, hanging ball, and canopy cover are not used in this type of installation. Canopy Cover Canopy 14. Align the canopy with the closemount screw holes Closemount Fig. -
Page 11: Wiring
WIRING CAUTION Fig. 16 Be sure outlet box is properly grounded or that a ground (green or bare) wire is present. Black (live) WARNING White (neutral) If house wires are different colors than referred to in the following step, stop immediately. A professional Bare/Green (ground) electrician is recommended to determine wiring. -
Page 12: Canopy Installation
CANOPY INSTALLATION 18. Lift the canopy up so the partially installed Fig. 18 mounting bracket screws are situated in the L-slots on each side of the canopy. Rotate the canopy clockwise and install the two remaining mounting bracket screws and washers from Step 4 (Fig.18). Mounting Mounting Bracket Screw... -
Page 13: Blade Installation
BLADE INSTALLATION 19. Remove motor screws from underside of motor Fig. 19 and save for blade arm attachment. Discard the plastic motor blocks but keep the screws (Fig. 19). Motor Block Motor Screw Motor Block Motor Screw 20. Partially insert the three blade screws along Fig. -
Page 14: Light Kit Installation
LIGHT KIT INSTALLATION 22. (Optional) To install the fan without a light kit: Fig. 22 Remove the three screws and washers from the upper switch housing. Align holes in optional cap with holes in upper switch housing. Re-insert screws and washers that were previously removed. Use a Phillips screwdriver (not included) to secure all screws (Fig. -
Page 15: Glass Shade
LIGHT KIT INSTALLATION 25. Remove socket ring from socket. Lift glass shade Fig. 25 onto the light kit and secure with socket ring using the socket ring tool. Repeat for each socket (Fig. 25). Socket Glass Shade Socket Ring Socket Ring Tool 26. -
Page 16: Operating Installation
OPERATING INSTRUCTIONS 28. Use the fan reverse switch, located on the side Fig. 28 of the light kit, to optimize your fan for seasonal performance (Fig. 28). Using a ceiling fan will allow you to raise your thermostat in the summer and lower your thermostat in the winter without sacrificing comfort. -
Page 17: Replacement Parts List
REPLACEMENT PARTS LIST For replacement parts, call the customer service department at 1-877-361-3883, 8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday. Model 50205 PIECE DESCRIPTION PART# Blade Arm 50205-A Blade 50205-B Shade 50205-C Loose parts bags containing (not shown): Mounting hardware, blade attachment... -
Page 18: Troubleshooting
TROUBLESHOOTING At least twice each year, lower the canopy to check the downrod assembly, and then tighten all screws on the fan. Clean the motor housing with only a soft brush or lint-free cloth to avoid scratching the finish. Clean the blades with a lint-free cloth. -
Page 19: Limited Lifetime Warranty
Monday - Thursday, 8 am - 6 pm, EST and Friday, 8 am - 5 pm, EST. Please have a copy of the receipt as proof of purchase. The Honeywell Trademark is used under license from Honeywell International Hong Kong China Electric Appliance Manufacture Co., Ltd.