Toshiba 43 QF5D Series Operating Instructions Manual page 20

Highlight either Soundbar or Receiver depending on
the product that you have connected then press Select.
Note: Make sure your soundbar or receiver is connected to
your TV and switched on.
The following example shows how to setup a soundbar
Now you need to select the brand of your soundbar.
Highlight the brand then press Select.
Make sure your soundbar is switched on and the
volume is up then press Select.
Press Standby on your TV remote control, wait 10
seconds then press the Standby button again.
You'll now be asked 'Did your soundbar turn off and
then back on when you pressed Standby'. If it did
highlight Yes and press Select, if it didn't highlight
No and press Select. You may need to repeat this
process multiple times.
When your soundbar eventually turns off and on, you
will be asked to press the volume up and down buttons.
Press the Volume + and - buttons.
If your volume level adjusted as expected highlight Yes
and press Select. If not select No and continue until
the volume level changes.
Your Fire TV remote has now been setup, it will
now switch your soundbar on and off and adjust the
volume level.
Now when you switch your TV on your soundbar will
also switch on. The TV speakers will be automatically
switched off.
Soundbar/Receiver Settings
Once you have setup your soundbar or receiver you
will now see either Soundbar or Receiver in the
Equipment Control menu. This will show you all the
settings for your device.
Highlight Soundbar or Receiver and press Select.
You will now see a list of settings.
Highlight the setting that you wish to adjust and press
Select.
Volume Increments: Set the amount the volume
increases or decreases when you ask Alexa to change
the volume. The default increment is set to 4.
Press Fast Forward or Rewind to increase or
decrease the increments. Press Option to restore
back to default settings.
Infrared Options: Changes the infrared options.
IR Profile, Timing and Repetition options will be
available.
Power Controls: Adjusts the power on/off settings
for your soundbar or receiver. Power On Delay,
Power Command and Power Control options may
be available.
Fire TV Input: Change the input, to which your
soundbar or receiver will switch to for watching Fire TV.
Change Soundbar/Change Receiver: If you
would like to change the soundbar or receiver that's
connected to your TV highlight Change Soundbar/
Change Receiver and press Select. To remove the
device highlight Change Soundbar/Change Receiver
and press the Option button.
Advanced Settings
Adjust the power timing if your soundbar or receiver
does not switch on/off.
Press Fast Forward or Rewind to increase or de-
crease the increments.
Press Option to restore back to default settings.
Live TV
This menu allows you to tune in your TV, manage the
channels, set up a CI card and set parental controls.
Highlight Live TV and press Select.
Tuning in your TV
You should have already tuned in your TV during the
initial setup process. But if you skipped the channel
scan step or if you need to retune your TV follow these
instructions.
Highlight Channel Scan and press Select.
You will be asked to check if your antenna cable is
plugged properly into the antenna input socket on your
TV. Press Select to proceed.
Select your scanning preference to install channels.
Cable/Terrestrial and Satellite options will be
available.
If the Cable/Terrestrial option is selected, the TV will
search for digital terrestrial or digital cable broadcasts.
Select the transmission method on the next screen and
press Select to start search.
If the Satellite option is selected, you can choose an
operator on the next step, if any available. You can also
choose to perform manual or complete channel scan.
Highlight the operator option you prefer and press
Select button to proceed. If an operator other than the
currently set one is selected, a confirmation dialogue is
displayed. Highlight Yes and press Select to continue
with the selected operator. The Satellite Connection
screen will be displayed next. Depending on your
previous selections some options may be preset
automatically. Change if necessary and proceed.
If you select Complete Channel Scan or Manual
Channel Scan option, you will have to select
the satellite in the next step. Then the Satellite
Connection screen will be displayed. Set the LNB
Type, LNB Power, DiSEqC Version, Single Cable,
ToneBurst and Scan Mode options manually
corresponding to your environment on the next screen.
If you select Manual Channel Scan, you will need to
English - 19 -