2. During repair or tests, do not view laser beam for 10 seconds or longer. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. Except DEH-X4600BT/XSUC DEH-X4600BT/XSUC CAUTION CAUTION...
Page 3
CAUTION Danger of explosion if battery is incorrectly replaced. Replaced only with the same or equivalent type recommended by the manufacturer. Discord used batteries according to the manufacturer's instructions. DEH-X4600BT/XNUC...
11. PCB CONNECTION DIAGRAM........................62 11.1 TUNER AMP UNIT..........................62 11.2 KEYBOARD UNIT ..........................66 11.3 CD CORE UNIT (S11.6VA) ........................68 11.4 CD CORE UNIT (S11.6STD)........................70 11.5 BT UNIT ..............................72 12. ELECTRICAL PARTS LIST .......................... 73 DEH-X4600BT/XNUC...
Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting temperatures (hard to melt/easy to harden). The following lead-free solders are available as service parts: Parts numbers of lead-free solder: GYP1006 1.0 in dia. GYP1007 0.6 in dia. GYP1008 0.3 in dia. DEH-X4600BT/XNUC...
2. SPECIFICATIONS 2.1 SPECIFICATIONS DEH-X4600BT/XNUC, DEH-X4600BT/XSUC General Power source ....14.4 V DC (10.8 V to 15.1 V al- USB standard specification lowable) ........USB 2.0 full speed Grounding system ....Negative type Maximum current supply Maximum current consumption ........1 A ........10.0 A...
Page 7
Gain ........ +6 dB to –24 dB Signal-to-noise ratio ..62 dB (IEC-A network) Phase ......Normal/Reverse Bluetooth Version ......Bluetooth 3.0 certified Output power ....+4 dBm Maximum (Power class 2) Note Specifications and the design are subject to modifications without notice. DEH-X4600BT/XNUC...
Page 8
Usable sensitivity ..... 28 µV (S/N: 20 dB) Signal-to-noise ratio ..62 dB (IEC-A network) Bluetooth Version ......Bluetooth 3.0 certified Output power ....+4 dBm Maximum (Power class 2) Note Specifications and the design are subject to modifications without notice. DEH-X4600BT/XNUC...
Page 9
Usable sensitivity ..... 28 µV (S/N: 20 dB) Signal-to-noise ratio ..62 dB (IEC-A network) Bluetooth Version ......Bluetooth 3.0 certified Output power ....+4 dBm Maximum (Power class 2) Note Specifications and the design are subject to modifications without notice. DEH-X4600BT/XNUC...
2.2 DISC/CONTENT FORMAT The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Pioneer Corporation is under license. Other trademarks and trade names are those of their respective owners. DEH-X4600BT/XNUC...
Volume too low Volume too high Volume fluctuating Sound interrupted 3.2 PCB LOCATIONS CD Core Unit (S11.6VA) CD Core Unit (S11.6STD) BT Unit Tuner Amp Unit A:DEH-X4600BT/XNUC B:DEH-X4600BT/XSUC C:DEH-X4650BT/XNCS D:DEH-X4650BT/XNGS E:DEH-X4690BT/XNID Keyboard Unit F:DEH-4600BT/XNEW5 Unit Number : QWM3637(A,B) Unit Number : QWM3638(C)
CD Mechanism Module 3.4 CLEANING Before shipping out the product, be sure to clean the following portions by using the prescribed cleaning tools: Portions to be cleaned Cleaning tools CD pickup lenses Cleaning liquid : GEM1004 Cleaning paper : GED-008 DEH-X4600BT/XNUC...
Page 15
REMOTE CONTROL SENSOR IC1941 SIR8440B5 ILM+B ILM+B VDSENS D1968 D1969,D1970, C D E D1971,D1972, D1973,D1974, D1975,D1976, Q1952 D1977,D1978, D1951 D1979,D1980, D1981,D1982 VDCONT D1966 D1952,D1953, D1954,D1955, CDRST D1956,D1957, Q1951 D1958,D1959, D1960,D1961, D1962,D1963, D1964,D1965, C D E CN1911 USB5V USB5V USB5V DEH-X4600BT/XNUC...
Page 16
LCOM MOTOR SLLDO- RESET RESET DSCSNS HOME CD DATA (CDSRQ,CDSTBY,SKIP, SCL,SDA,DATA,BCLK,LRCK,WAIT) S903 S901 DSCSNS HOME :DEH-X4600BT/XNUC :DEH-X4600BT/XSUC D E F :DEH-X4650BT/XNCS :DEH-X4650BT/XNGS :DEH-X4690BT/XNID PICKUP UNIT CD CORE UNIT(S11.6 STD) :DEH-4600BT/XNEW5 (P10.6)(SERVICE) CN101 RF AMP, CD DECODER DIGITAL SERVO/DATA • PROCESSOR...
In case of the above signal, the communication Source keys with Grille microcomputer may fail. operative If the time interval is not 300 msec, the oscillator may be defective. Source ON SYSPW <- H Pin 8 Completes power-on operation. (After that, proceed to each source operation) DEH-X4600BT/XNUC...
: Servo-related errors CD Off, Eject, ACC Off, Back-up Off, Communication reset, Reset Load NG/Eject NG(50) : Reload, Eject, ACC Off, Back-up Off, Communication reset, Reset Failure in retried turning for ejection : CD On, Eject, ACC Off, Back-up Off, Communication reset, Reset DEH-X4600BT/XNUC...
Page 19
Transfer the audio files to the USB storage device fails to disappear even after the engine is and connect. switched off/on, contact your dealer or an authorized Pioneer Service Station for The connected USB storage device has security en- assistance. abled.
Page 20
NO BT DEVICE GO TO BT MENU TO REGISTER If the error message is still displayed after performing the above action, please contact your No Bluetooth device found. dealer or an authorized Pioneer Service Station. Follow the instructions that appear on the screen. Pandora CONN.
Page 21
Follow the instructions that appear on the screen. CHECK APP Connection to the application failed. Follow the instructions that appear on the screen. START UP APP The application has not started running yet. Follow the instructions that appear on the screen. DEH-X4600BT/XNUC...
Conf. LCD pattern 1 ILM(2) BAND Draw 3 (* And change ILM color) (If not have, ILM(1) light on) Conf. LCD pattern 2 ROTARY center Draw 4 ILM(1) Drawings Style Draw1 ALL light up Draw2 ALL light off Draw3 Draw4 DEH-X4600BT/XNUC...
The screen gets still when entering this item. On (an initial value or On (state when setting value of default entering test mode) Switching to next display menu) by pressing “ 1 ” + “ 3 ” buttons together. DEH-X4600BT/XNUC...
The display is continued until the power supply is turned OFF. If the power supply is turned ON again, the display is not changed. The upgrading using USB is disabled, so it is necessary to write programs in serial Flash using E10A. DEH-X4600BT/XNUC...
When the power is turned on/off the gain of the RFAMP is reset to 0 dB. At the same time all the self-adjusting values shall return to the default setting. Do not do Tracking Servo Close before doing Focus Servo Close. (Because the overcurrent flows) DEH-X4600BT/XNUC...
Slide the Tuner Amp Assy in the direction of the arrow. Lift off the Tuner Amp Assy from the Heat Sink side. The Tuner Amp Assy is fixed into the ditch. Disconnect the FFC and then remove the CD Mechanism Module. CD Mechanism Module Fig.2 DEH-X4600BT/XNUC...
Page 28
Remove the two screws and then remove the Tuner Amp Unit. Remove the screw and then remove the BT Unit. BT Unit Fig.3 - Attention of removing (Fig.4) Don’t remove this screws excluding the dismantlement of the CD Mechanism Module. CD Mechanism Module Fig.4 DEH-X4600BT/XNUC...
Page 29
1. Attach the button from the front side of the panel. Fig.7 2. Attach the spring to the arm as shown in the figure. The bended tip of the spring is set to this side. Hitch the spring to the groove. Fig.8 DEH-X4600BT/XNUC...
Page 30
4. Fit the boss on the lower side of the arm in the lower hole of the panel, and then warp the rib on the panel in the direction shown in the figure and fit the boss of the arm in the panel. Fig.9 DEH-X4600BT/XNUC...
Page 31
2. Be careful not to hold the solid line portions or the CRG mecha part or insert foreign substances, to prevent distortion. 3. When holding the sides of the upper chassis, do not apply excessive force to prevent distortion. (Approx. 8N or less) Handling OK Handling NG DEH-X4600BT/XNUC...
Page 32
Fig 3 Fig 4 [Incorrect built-in state] The chassis is not nipped between Outer holder Normal built-in state the PU case and the PU rack. Rear end of feeding screw DEH-X4600BT/XNUC...
1k ohms in series. The load and eject operation is not guarantied with the mechanism upside down. If the mechanism is blocked due to mistaken eject operation, reset the product or turn off and on the ACC to restore it. DEH-X4600BT/XNUC...
Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the average angle. Hint Reloading the disc changes the clamp position and may decrease the "wobble". DEH-X4600BT/XNUC...
The frequency of the clock signal is 600 kHz that is divided by 20th of the oscillation frequency of X601 (12MHz). The clock signal should be 600 kHz(- 25 Hz, + 25 Hz). If the clock signal is out of the range, the X'tal (X601) should be replaced with new one. DEH-X4600BT/XNUC...
(In the case of no amount instructions,apply as you think it appropriate.) 9.1 PACKING 4600BT/XNEW5 4600BT/XNEW5 4600BT/XNEW5 4600BT/XNUC 4600BT/XSUC 4650BT/XNCS 4650BT/XNGS 4690BT/XNID 4600BT/XNUC 4650BT/XNCS 4600BT/XSUC 4650BT/XNGS 4650BT/XNCS 4690BT/XNID 4650BT/XNGS 4600BT/XNEW5 4690BT/XNID 4600BT/XNUC 4600BT/XSUC 4600BT/XNUC 4600BT/XSUC 4650BT/XNCS 4600BT/XNUC 4650BT/XNGS 4600BT/XSUC 4690BT/XNID DEH-X4600BT/XNUC...
Page 39
See Contrast table (2) 17-8 Caution Card See Contrast table (2) Unit Box See Contrast table (2) (2) CONTRAST TABLE DEH-X4600BT/XNUC, DEH-X4600BT/XSUC, DEH-X4650BT/XNCS, DEH-X4650BT/XNGS, DEH-X4690BT/XNID and DEH-4600BT/XNEW5 are constructed the same except for the following: DEH-X4600BT DEH-X4600BT DEH-X4650BT DEH-X4650BT DEH-X4690BT DEH-4600BT Mark No.
Page 40
* QRB3336 Finnish * QRB3337 Danish * QRB3338 Portuguese * QRB3339 Greek * QRB3340 Turkish All operation manuals are supplied in PDF files by the CD-ROM. Regarding the availability of paper manual, contact Pioneer Service representative in your region. DEH-X4600BT/XNUC...
Page 43
See Contrast table (2) Shield Case YNC5123 > Fuse (10 A) YEK5001 BT Unit QWM3750 (2) CONTRAST TABLE DEH-X4600BT/XNUC, DEH-X4600BT/XSUC, DEH-X4650BT/XNCS, DEH-X4650BT/XNGS, DEH-X4690BT/XNID and DEH-4600BT/XNEW5 are constructed the same except for the following: DEH-X4600BT DEH-X4600BT DEH-X4650BT DEH-X4650BT DEH-X4690BT DEH-4600BT Mark No.
Symbol indicates a capacitor. RGBCK/ILMCLR1 No differentiation is made between chip capacitors and US5V USB5V discrete capacitors. CN1931 DPDT DEH-X4600BT/XNUC USBGND KYDT DEH-X4600BT/XSUC The > mark found on some component parts indicates RGBDT DEH-X4650BT/XNCS ROT0 the importance of the safety factor of the part.
Page 47
B.REM&A.ANT C330 Dim off 12.13 V R814 2.2k KYDT Q875 Dim on 8.03 V DPDT LTC043EEB R816 2.2k ROT0 except F ILMPW D941 DZ2J068M0 DZ2J075M0 R817 2.2k ROT1 R943 6.8k SWVDD R944 1.2k L851 IC801 DPDT OUTY TC7SET08FUS1 SWVDD DEH-X4600BT/XNUC...
Page 48
The pin number of left side is a number on the PCB (silk printing). The pin number of right side (in the IC frame) means the pin number of IC itself. DEH-X4600BT/XNUC...
Page 49
POWER SUPPLY mber of IC itself. DEH-X4600BT/XNUC...
DISC. C204 C222 A.VDD2 0.1u/10 CKS4808-A T.ACT: Applying positive voltage to TOP, the lens moves outer circumference of DISC. NO MOUNT PARTS (NM) REFO REFO1 DEH-X4600BT/XNUC REFOUT C223 REFO2 C229 Land for manual soldering DEH-X4600BT/XSUC 68p/50 0.1u/10 ADCIN DEH-X4650BT/XNCS...
1 V/div fRFAGC 500 mV/div 500 mV/div 500 mV/div 9TIN 500 mV/div Focus Search waveform Track Open waveform 100 Track Jump waveform (32 Track Jump x 3) Ref.: Ref.: Ref.: REFO REFO REFO Mode: Mode: Mode: TEST TEST TEST DEH-X4600BT/XNUC...
Page 61
12 cm CD Eject operation 12 cm CD Eject operation Ref.: Ref.: Mode: Mode: Normal Normal 500 μs/div fRFAGC 1 V/div 9TIN 1 V/div 1 V/div aFIN 1 V/div μ Black Dot (800 m) during play Ref.: REFO Mode: Normal DEH-X4600BT/XNUC...
11.3 CD CORE UNIT (S11.6VA) CD CORE UNIT(S11.6VA) SIDE A (except B) DEH-X4600BT/XNUC DEH-X4600BT/XSUC PU UNIT(P11) DEH-X4650BT/XNCS (SERVICE) DEH-X4650BT/XNGS DEH-X4690BT/XNID DEH-4600BT/XNEW5 TH201 R254 C235 CN101 LOAD/CRG R246 MOTOR R232 HOME S901 C201 CN702 R253 R245 C238 C710 C299 R706 R297...
11.4 CD CORE UNIT (S11.6STD) CD CORE UNIT (S11.6STD) SIDE A (only B) DEH-X4600BT/XNUC DEH-X4600BT/XSUC DEH-X4650BT/XNCS DEH-X4650BT/XNGS PICK UP UNIT(P10.6) (SERVICE) DEH-X4690BT/XNID DEH-4600BT/XNEW5 LOAD/CRG R254 TH201 C235 MOTOR CN101 R232 R246 HOME C102 S901 C201 D101 CN702 R253 R245 C238...
The expression of the unit in this manual is shown by u instead of . Please do not make a mistake. Circuit Symbol and No. Part No. Circuit Symbol and No. Part No. Unit Number : QWM3636(F) A:DEH-X4600BT/XNUC Unit Name : Tuner Amp Unit B:DEH-X4600BT/XSUC C:DEH-X4650BT/XNCS MISCELLANEOUS...
Page 74
R 302 (A,82,125) RS1/16SS471J R 627 (A,112,88) RS1/16SS221J R 628 (A,111,90) RS1/16SS221J R 303 (A,74,127) RS1/16SS471J R 629 (A,109,92) RS1/16SS221J R 304 (A,78,126) RS1/16SS471J R 630 (A,110,89) RS1/16SS221J R 305 (A,90,127) RS1/16SS103J R 631 (A,108,92) RS1/16SS473J R 306 (A,90,129) RS1/16SS221J DEH-X4600BT/XNUC...
Page 75
R 808 (A,124,20) RS1/10SR222J C 255 (A,35,132) 4.7 uF CCG1201 R 809 (A,115,21) RS1/10SR220J C 256 (A,31,130) 4.7 uF CCG1201 R 810 (A,114,21) RS1/10SR220J R 813 (A,107,16) RS1/10SR222J C 257 (A,26,131) CCSSCH101J50 R 814 (A,101,19) RS1/10SR222J C 258 (A,21,131) CCSSCH101J50 DEH-X4600BT/XNUC...
Page 76
(A,121,96) CKSSYB104K10 C 447 (A,157,83) (A,B,C) CKSRYB105K10 C 683 (A,120,94) CCSSCJ3R0C50 C 448 (A,158,85) (A,B,C,F) CKSSYB104K10 (A,158,85) (D,E) CKSSYB103K16 C 701 (A,111,40) CKSSYB103K16 C 449 (A,161,85) CCSSCH9R0D50 C 704 (A,120,39) CCSSCH100D50 C 450 (A,161,90) CCSSCH9R0D50 C 705 (A,118,39) CCSSCH100D50 DEH-X4600BT/XNUC...
Page 77
(A,133,6) Blue LED(A,B,C,D,E) FC-F1608BK-470H5 R 1980 (B,18,23) (F) RS1/10SR682J D 1963 (A,144,6) Blue LED(A,B,C,D,E) FC-F1608BK-470H5 R 1982 (B,68,12) (F) RS1/10SR222J R 1984 (B,54,12) (F) RS1/10SR182J D 1964 (A,14,32) Blue LED(A,B,C,D,E) FC-F1608BK-470H5 R 1986 (B,138,19) (F) RS1/10SR182J D 1965 (A,10,11) Blue LED(A,B,C,D,E) FC-F1608BK-470H5 DEH-X4600BT/XNUC...
Page 78
(B,15,54) Transistor LTA123JUB R 307 (A,26,9) RS1/16SS102J X 201 (B,25,49) Ceramic Resonator 16.934 MHz CSS1603 R 308 (A,26,12) RS1/16SS472J R 309 (A,35,7) RS1/16SS473J S 901 (A,42,53) Spring Switch(HOME) CSN1080 R 310 (B,31,9) RS1/16SS472J S 903 (B,21,12) Spring Switch(DSCSNS) CSN1081 DEH-X4600BT/XNUC...
Page 79
C 214 (B,17,26) CKSSYB473K16 C 215 (B,19,28) CKSSYB104K10 C 216 (B,12,33) CKSSYB182K50 C 217 (B,10,34) CCSSCH560J50 C 218 (B,10,36) CCSSCH4R0C50 C 219 (B,14,34) CKSSYB104K10 C 220 (A,18,38) CKSSYB104K10 C 221 (B,14,32) CKSSYB104K10 C 222 (B,13,37) CKSSYB104K10 C 223 (B,12,42) CCSSCH680J50 DEH-X4600BT/XNUC...