Advertisement
5.8.
HARD WATER
If the tap water used is very calcareous, it is recommended to use distilled or de-mineralized water in the Steamer.
If the use of very calcareous water is unavoidable, it is recommended to clean the water tank regularly.
5.9.
FABRICS AND FINISHES
CAUTION: Some fabrics and finishes are not compatible with steam. DO NOT use steam on leather, waxed floors, synthetic fabrics,
velvet and other fragile materials. When using steam appliances, always refer to the manufacturer's instructions for use and pre-test at a
non-visible location.
5.10.
GLASS / MIRRORS
WARNING!: Never apply steam to windows or mirrors with a temperature below 0 °C. Thermal shock resulting from extreme
‰
temperature deviations can break windows and mirrors.
6. STORAGE
WARNING! Always empty the Steamer after use. Never leave water in the tank when storing the unit.
‰
6.1.
Disconnect from mains supply.
6.2.
Empty all remaining tank pressure by pressing the steam trigger.
6.3.
Allow the unit to cool completely (10 minutes minimum). When the appliance is cold, lock the steam trigger and remove the accessories.
6.4.
Empty all remaining water from the tank by tilting the unit to one end. Never leave water in the tank when the unit is not in use or
stored.
6.5.
Replace the filler cap and store the Steamer in a safe and dry place. Protect from frost.
7. MAINTENANCE
7.1.
CLEANING To clean the water tank and de-scale, proceed as follows.
WARNING! Remove from mains supply.
‰
WARNING! Never clean the water tank whilst it is still hot.
‰
DO NOT use detergent to clean the tank.
8
7.1.1.
Mix a 50/50 solution of 250 ml of white vinegar and 250 ml of water. Use the measuring cup.
7.1.2.
Pour the solution into the unheated cold tank using the funnel.
7.1.3.
Leave the solution in the tank for about 30 minutes.
7.1.4.
After 30 minutes, empty the tank.
7.1.5.
Repeat steps 7.1.1 to 7.1.4, if necessary.
7.1.6.
Rinse well with water.
7.1.7.
Replace the tank filler cap and store in a safe and dry place.
8. QUESTIONS
8.1.
WHY DOES WATER COME OUT OF THE NOZZLE?
Steamer generates a large amount of steam that can condense in water in the hose and extension tubes after a period of no use or
cooling of the unit. Empty this water by operating the steam trigger over a bucket or sink. Once this water has drained, use the device
normally.
8.2.
NO STEAM IS COMING OUT?
Check that the hose is not bent. Make sure that the water tank is not empty.
8.3.
I CANNOT REMOVE THE FILL CAP?
Make sure the Steamer is completely de-pressurized. The filler cap is designed so that it can not be removed while the unit is still
under pressure. To do this, empty all residual pressure from the tank by pressing the steam trigger. The steam trigger can be
unlocked by engaging the steam trigger lock latch in the ON position. Once the pressure is discharged from the tank, the filler cap
of the tank can be opened.
8.4.
THE STEAM FLOW IS IRREGULAR, THE APPLIANCE "COUGHS".
Slight blockage caused by soil or other foreign matter that can prevent the flow of steam from arriving continuously. Clean the water
tank as shown in Section 7.1.
8.5.
I SEE THE CONDENSED WATER ON THE GAUGE OF THE STEAM PRESSURE GAUGE?
Any condensation that may appear will disappear in a short period of time. No action is necessary.
8.6.
CAN I USE BOILED WATER FROM MY KETTLE?
No. Boiled water concentrates the minerals that form the scale. Never use pre-boiled water in the Steamer.
8.7.
CAN I LEAVE WATER IN THE STEAMER?
No. Water left in the water tank for a prolonged period may deteriorate the components of Steamer and deposit scale. Never leave
water in the Steamer; always empty it after use. If the tap water used is very hard, it is recommended to use distilled water to prolong
the service life and increase the performance of Steamer.
8.8.
ROTATING BRUSH
The inner part will rotate due to the high steam pressure applied. Push the rotating brush pipe on the extension tube until the knob fits
correctly in the oval opening of the rotating brush pipe. Use the rotating brush to clean all kind off surfaces with a gentle push
and move the brush in the required direction. The rotating part will clean the surface.
WARNING! DO NOT use the brush towards your face or other parts of the body. Hot steam is coming out!
‰
© Jack Sealey Limited
Original Language Version
VMSC01.V2
Issue:2(H) 31/03/22
Advertisement
