Sealey ES680D Quick Start Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear safety
instructions
footwear
1. SAFETY
WARNING! Ensure all Health and Safety, local authority, and general workshop practice regulations are strictly adhered to when
‰
using this equipment.
Before using the stand ensure it is in good working order.
9
Ensure the stand legs and arms are locked with respective pins and R clips before use.
9
Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the
9
warranty.
DO NOT use unit if damaged.
8
Keep the stand clean for best and safest performance.
9
Use only with legs folded down and pinned.
9
Locate the stand in a suitable work area, keep area clean and tidy and free from unrelated materials. Ensure there is adequate
9
lighting.
Use on a firm, level surface capable of sustaining the stand and the load.
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
Ensure all non-essential persons keep a safe distance whilst the stand is in use.
9
Lock mounting plate in position with locking pin before fixing a load and ensure the load is centred and securely mounted on the
9
mounting plate.
When an engine is mounted, take the weight of the engine on the handle before removing the locking pin.
9
Ensure the stand and load are stable.
9
To move a loaded stand, steady the load and push from behind the main post of the stand so that the castor wheels are ahead of the
9
load.
DO NOT pull the unit backwards, or push from the side, as this may cause the stand to tip.
8
DO NOT concentrate a heavy load to either side or end of the Engine Stand. This can cause the balance to shift suddenly, tipping
8
the Engine Stand and its load which can quickly cause severe injury and property damage!
Ensure surface over which the stand is to travel is strong enough to take the stand and load and that it is not cracked, uneven,
9
sloped or obstructed.
DO NOT allow untrained persons to use the stand.
8
DO NOT exceed the rated capacity of 680kg.
8
DO NOT use to support humans or animals.
8
DO NOT climb on the Engine Stand.
8
▲ DANGER! DO NOT work under an engine mounted on the stand.
DO NOT use the stand for purposes other than those for which it is designed.
8
When not in use store stand in a safe, dry, childproof area.
9
Use extreme caution while rotating the hand crank to rotate the load as a large, top-heavy engine or similar object could result in a
9
sudden imbalance condition and cause the Engine Stand to suddenly tip.
DANGER! While rotating, always stand behind the crank end of the stand and make constant observations of the casters. If any
▲
indication of instability occurs, STOP IMMEDIATELY!
DANGER! PINCH/CRUSH HAZARD! This Engine Stand has moveable components that can crush and pinch. Keep fingers and
▲
hands away from pinch points when operating.
2. INTRODUCTION
This engine stand accepts a wide variety of engines and transmissions. The Geared Handle Drive allows for easy and accurate 360º rotation in
order to access all parts of the engine. Mounting head has four fully adjustable arms with bolt holes to accommodate various load sizes. Fitted
with screw lock to ensure load is secured. Swivel castors provide excellent manoeuvrability. Assembled with clevis pins and clips so the stand
can be folded for storage. Maximum Load Length: 700mm.
3. SPECIFICATION
Model No:.................................................................ES680D
Capacity: ...................................................................... 680kg
© Jack Sealey Limited
680KG FOLDING 360º ROTATING ENGINE
STAND WITH GEARED HANDLE DRIVE
MODEL NO:
Wear protective Wear protective
clothing gloves
Original Language Version
ES680D
Warning:
Pinch crush
hazard
Size (W x D x H): ..................................1080 x 895 x 890mm
Max. Load Length:.......................................................700mm
ES680D Issue:2 05/09/23