Page 2
Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems.
You can find the system manual at the following link: (https://support.industry.siemens.com/cs/us/en/ps/25277) Trademarks The following and possibly other names not identified by the registered trademark sign ® registered trademarks of Siemens AG: SIMATIC RTLS SIMATIC RTLS PCB OEM PULSE Operating Instructions, 03/2020, C79000-G8976-C552-03...
Page 6
Siemens’ products and solutions undergo continuous development to make them more secure. Siemens strongly recommends that product updates are applied as soon as they are available and that the latest product versions are used. Use of product versions that are no longer supported, and failure to apply the latest updates may increase customers’...
Page 7
Introduction To stay informed about product updates, subscribe to the Siemens Industrial Security RSS Feed under: (https://support.industry.siemens.com/cs/us/en/ps/15247/pm) Recycling and disposal The products are low in harmful substances, can be recycled and meet the requirements of the Directive 2012/19/EU for disposal of waste electrical and electronic equipment (WEEE).
The RTLS transponder can be damaged by electrostatic discharge (ESD). Take suitable precautionary measures when unpacking and operating the transponder to avoid damage. Order data RTLS PCB OEM PULSE Table 2- 1 Order data RTLS PCB OEM PULSE Article number SIMATIC RTLS PCB OEM PULSE 6GT2700-8AF03 6GT2700-8AF13 CMIIT 6GT2700-8AF23 6GT2700-8AF33...
Flashes every three seconds when the transponder is active Is off when the transponder is inactive Lights up for 0.6 seconds on system start Flashes every 0.1 seconds after a watchdog reset SIMATIC RTLS PCB OEM PULSE Operating Instructions, 03/2020, C79000-G8976-C552-03...
The antenna is connected to the PCB via a 5 cm long U.FL cable. The contacts used are P3 on the PCB and P1 on the antenna. Figure 2-1 All dimensions specified in millimeters. Antenna Figure 2-2 All dimensions specified in millimeters. SIMATIC RTLS PCB OEM PULSE Operating Instructions, 03/2020, C79000-G8976-C552-03...
The label is required to identify the device with the installed transponder in the Locating Manager. SIMATIC RTLS PCB OEM PULSE Operating Instructions, 03/2020, C79000-G8976-C552-03...
(0 Hz - 300 GHz) The products described in these operating instructions meet the requirements of EU directive 2014/30/EU "Electromagnetic Compatibility" according to the designated standards for the following areas of application. SIMATIC RTLS PCB OEM PULSE Operating Instructions, 03/2020, C79000-G8976-C552-03...
Page 18
3.2 of the Directive 2014/53/EU; Part 2: Requirements for UWB location tracking Note The specified approvals are only valid if the corresponding symbol is printed on the device. SIMATIC RTLS PCB OEM PULSE Operating Instructions, 03/2020, C79000-G8976-C552-03...
Page 19
Approvals FCC information Siemens SIMATIC RTLS PCB OEM PULSE (MLFB 6GT2700-8AF13); FCC ID NXWOEMPULSE This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Page 20
Approvals IC information Siemens SIMATIC RTLS PCB OEM PULSE (MLFB 6GT2700-8AF33); IC ID 267X- OEMPULSE This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.