1. Manuals
  2. Brands
  3. Dell Manuals
  4. Monitor
  5. U2722DX
  6. Service manual

Dell U2722DX Service Manual

Hide thumbs Also See for U2722DX:
Table of Contents

Advertisement

Quick Links

Download this manual
Service Manual - U2722D/DX
Version: 01
Date: 2021/10/30

Advertisement

Table of Contents
loading

Related Manuals for Dell U2722DX

Summary of Contents for Dell U2722DX

  • Page 1 Service Manual - U2722D/DX Version: 01 Date: 2021/10/30...

  • Page 2: Important Safety Notice

    1. Important Safety Notice Product Announcement: ! To ensure using a proper screwdriver, follow the This product is certificated to meet RoHS torque and force listed in assembly and Directive and Lead-Free produced definition. disassembly procedures to unscrew screws. Using approved critical components only is ! Using Lead-Free solder to well mounted the recommended when the situation to replace parts.
  • Page 3 HDMI 1.8 M cable (U2722DX Only) NOTE: For replacement of power cord, connectivity cable and external power supply (if applicable), contact Dell: 1. Go to https://www.dell.com/support. 2. Verify your country or region in the Choose A Country/Region drop-down menu at the bottom-right corner of the page.
  • Page 4 3. Wiring Connectivity Diagram...
  • Page 5 4. How to connect and disconnect power cable/ connectivity cable WARNING: To change power cable/ connectivity cable, switch off power before unplugging the cable and replugging in required cable.
  • Page 6 4. How to connect and disconnect power cable/ connectivity cable...

  • Page 7: Disassembly And Assembly Procedures

    This “Disassembly and Assembly Procedures” is for EMEA only, joystick key cable and Usb EDP cable from the not for other regions. Please note that Dell will deem warranty void connectors of the interface board, and then remove if any disassembly is done on the monitors.
  • Page 8 5. Disassembly and Assembly Procedures Use a Philips-head screwdriver to remove 13pcs screws for unlocking the middle bezel with the panel module. (No.1~13 screw size=M3x5, Torque=5 0.5kgfxcm) ± se a Philips-head screwdriver to remove 4pcs screws for unlocking the bracket chassis module with the panel (No.1~4 Screw size= M3x5, Torque=5±0.5kgfxcm) Disconnect the panel lamp from the connector of the...
  • Page 9 5. Disassembly and Assembly Procedures Remove the Mylar tape from the hooks of the bracket. Use a Philips-head screwdriver to remove 6pcs screws for interface board and power board. (No.1 screw size=M4x8, Torque=7 kgfxcm; ±1 No.2~6 screw size=M3x7.5, Torque=7 kgfxcm) ±1 Remove the power board board and interface board from the...
  • Page 10 5. Disassembly and Assembly Procedures Take a black mylar to insert the hooks of the bracket 5.2 Assembly Procedures: Place a bracket chassis base on a protective to cover the power board, then tear off the gum cushion, then stick 3pcs Silicon sheets on the paper of the panel lamp cable.
  • Page 11 5. Disassembly and Assembly Procedures Move the middle bezel with the LED board close to the panel unit, then assemble the middle bezel with the front bezel and panel module. Adjust the bracket chassis module, and then u se a Philips-head screwdriver to tighten 4pcs screws for locking the bracket chassis module with the panel (No.1~4 Screw size= M3x5, Torque=5±0.5kgfxcm)
  • Page 12 5. Disassembly and Assembly Procedures Connect the LED cable to connector of the interface Take 1pcs joystick key and 1pcs OSD board, board, then paste 1pcs aluminum foil to fix the bracket assemble the joystick key with the OSD board. on the specific position as the picture below shown.
  • Page 13 5. Disassembly and Assembly Procedures Use a Philips-head screwdriver to tighten 4pcs screws for locking the rear cover with the unit. Stick two pieces of label on the specific positions, then insert a DP out Cap into the DP out connector. (No.1~4 screw size=M4x11;...

  • Page 14: Troubleshooting Instructions

    LED remains white. Also, depending upon the selected input, one of the dialogs shown below will continuously scroll through the screen. No DP Cable The display will go into Standby Mode in 4 minutes. www.dell.com/U2722D/DX/DE No HDMI Cable The display will go into Standby Mode in 4 minutes. www.dell.com/U2722D/DX/DE 4.

  • Page 15: Common Problems

    • Cycle power on-off. spots • Pixel that is permanently off is a natural defect that can occur in LCD technology. • For more information on Dell Monitor Quality and Pixel Policy, see Dell Support site at: https://www.dell.com/pixelguidelines. Stuck-on Pixels LCD screen has •...
  • Page 16 6. Trouble Shooting Instructions Common What You Possible Solutions Symptoms Experience Intermittent Monitor • Ensure that the video cable connecting the Problems malfunctions on monitor to the computer is connected properly & off and is secure. • Reset the monitor to factory settings. •...

  • Page 17: Product Specific Problems

    6. Trouble Shooting Instructions Product Specific Problems Problem What You Possible Solutions Experience Screen image is Image is • Check the Aspect Ratio setting in the Display too small centered on menu OSD. screen, but • Reset the monitor to factory settings. does not fill entire viewing area...
  • Page 18 USB-C connection. (U2722DE only) • Ensure that you use only Dell approved adapter or the adapter that comes with the product. • Ensure that the USB-C cable is not damaged. Intermittent Intermittent •...

  • Page 19: Universal Serial Bus (Usb) Specific Problems

    6. Trouble Shooting Instructions Universal Serial Bus (USB) Specific Problems Specific What You Possible Solutions Symptoms Experience USB interface is USB peripherals • Check that your display is turned ON. not working are not working • Reconnect the upstream cable to your computer.

This manual is also suitable for:

U2722d

Table of Contents