Page 9
BBU MODEL ジャンパー マザーボード 装置前面側 サイドカバーとフロントベゼルを取り付け直します。 装置構成情報のアップデート 本製品を使用して本体装置の構成を変更した場合は、以下の方法で装置構成情報の最新化 を実施してください。 [Express5800/T110i-S、iStorage NS100Thの場合] 次のWebサイトを参照し、SDRのアップデートを実施してください。 NECサポートポータルサイト(https://www.support.nec.co.jp/) →「サポート情報」の「ハードウェア」を選択。 →「型番・モデル名から探す」を選択。 → 本製品を使用する本体装置のモデル名 (例:T110i-S、NS100Th)を入力。 →「キーワード(全て含む)」に「SDR」を入力し絞り込み検索をしてください。 [Express5800/T110j-S、iStorage NS100Tiの場合] ①ジャンパー設定変更時に取り外した、カバーやケーブルを取り付ける。 ②電源ユニットに電源コードを取り付け、POWERスイッチを押し、本体装置の電源をONにする。 ③以下のメッセージが表示されたら、POWERスイッチを押し、本体装置の電源をOFFにする。 Error:System HWID doesn’t match with system SKU ROM ID, please do AC power off/On after 10 seconds.
N8181-153 Internal simple UPS Control KIT User's Guide Preface Thank you very much for your purchase of this product. The guide is intended to allow you to install and use the product correctly and safely. Read the guide carefully before handling the product.
Safety Precautions Observe the following notes to use the product safely. WARNING If smoke, odor, or noise is present, immediately turn off the server and disconnect the power plug from the outlet, then contact the store where you purchased the product or your maintenance service company.
Page 14
1.Components Check components according to the list below. Description Item No. Name Q'ty - Control kit - Battery holder bracket - LED cable - Flat-head screw - Countersunk screw - Cable tie - Device tray User's guide This document Warranty card Available only in Japan 4.
Page 15
2.Installing this product to the Server 1. See overview of installation and removal for preparations. To remove the side cover and the front bezel. 2. Remove the blank cover. Push the tab on the device tray(①) and pull out the device tray from the 3.5- inch expansion bay(2)(②).
Page 16
3-3. Remove two power cables from the power connector on the motherboard. Rear Side Please refer step 7-4 for detailed power connector location on the motherboard. Motherboard Front Side 3-4. Connect the I2C cable of the control kit to the I2C connector on the motherboard. I2C Cable Please refer step 7-4 for detailed I2C connector location on the motherboard.
Page 17
3-6. Connect two power cables of control kit to the power connector on the motherboard you removed in step 3-3. Please refer step 7-4 for detailed power connector location on the motherboard. Install the LED cable to the device tray you removed in step2. If backup device is already installed in Note 3.5-inch expansion bay(2), use the...
Page 18
5. Insert the device tray with LED cable to 3.5-inch expansion bay(2). Then connect LED cable to the CN102 connector of the control kit. CN102 Connector LED Cable Device tray with LED cable Install for N8181-152 Internal simple UPS with the following procedures. 6-1.
Page 19
6-3. Connect the cable of the internal simple UPS (a power cable and two signal cables) to the CN104, CN105 and CN103 connector of the control kit. CN104 Connector CN105 Connector CN103 Connector Motherboard’s Jumper setting Important To avoid system malfunction, do not change other jumper setting. Tips The procedure of installing this product depends on your server type.
Page 20
[In case of Express5800/T110j-S] When using N8181-152 internal simple UPS, set jumper (BBU MODEL) on the motherboard to “Enabled” (Set to 2-3). If N8181-152 internal simple UPS is not used, set jumper (BBU MODEL) on the motherboard to “Disabled” (Set to 1-2). Rear Side Enabled Disabled...
Page 21
3/BMC Management Console, NEC ESMPRO/ServerManager, or Server Configuration Utility. For details, Refer the online help stored in EXPRESSSCOPE Engine 3/ BMC Management Console and NEC ESMPRO/ServerManager, Refer chapter 2 (2.7 Battery Configuration) in the “Maintenance Guide” about Server Configuration Utility.
Page 22
[Display Most Recent IPMI Data] - [Current Sensor Status] - [Current (Battery Power)] Remarks (1) No part of this manual may be reproduced in any form without the prior written permission of NEC Corporation. (2) The contents of this User's Guide may be revised without prior notice.