Related Manuals for Miele KS 4783 ED edt/cs
Summary of Contents for Miele KS 4783 ED edt/cs
- Page 1 Operating instructions Refrigerator To avoid the risk of accidents or damage to the appliance it is essential to read these instructions before it is installed and used for the first time. en-SA M.-Nr. 12 124 730...
-
Page 2: Table Of Contents
Contents Warning and Safety instructions..............Caring for the environment ................16 Installation......................17 Installation site..................... 17 Climate range ....................18 Ventilation requirements ..................18 Installing several refrigeration appliances ............19 Side-by-side installation................. 19 Changing the door hinging.................. 19 Fitting supplied wall spacers................20 Installing the refrigeration appliance .............. - Page 3 Holiday mode ................... 45 Switching on the lock function /............. 46 Changing the time before the door alarm is triggered ....... 46 Miele@home ....................47 Adjusting the volume of alarms and buzzers /........49 Adjusting the display brightness ............... 50 Switching off demo mode ................50 Resetting the settings to their default settings .........
- Page 4 Contents Problem solving guide ..................66 Noises......................... 72 Service........................ 73 Contact in case of malfunction ................73 Warranty ......................73 Copyrights and licences ................... 74...
-
Page 5: Warning And Safety Instructions
Miele cannot be held liable for injury or damage caused by non- compliance with these instructions. Keep these operating and installation instructions in a safe place... - Page 6 The refrigeration appliance is also not suitable for use in areas where there is a risk of explosion. Miele cannot be held liable for damage caused by improper or incorrect use or operation of the appliance. ...
- Page 7 Warning and Safety instructions Safety with children Children under 8 years of age must be kept away from the refrigeration appliance unless they are constantly supervised. Children 8 years and older may only use the appliance unsupervised if they have been shown how to use it in a safe way and recognise and understand the consequences of incorrect operation.
- Page 8 In the event of damage: - Avoid naked flames or anything which creates a spark. - Disconnect the refrigeration appliance from the mains electricity supply. - Ventilate the room where the refrigeration appliance is located for several minutes. - Contact your Miele dealer.
- Page 9 If the electrical connection cable supplied is damaged, it must only be replaced by an original spare part to prevent a hazard for the user. Miele can only guarantee the safety of the appliance when original Miele spare parts are used.
- Page 10 Faulty components must only be replaced with genuine Miele original spare parts. Miele can only guarantee the safety standards of the appliance when Miele replacement parts are used. This refrigeration appliance is supplied with a special lamp to cope with particular conditions (e.g.
- Page 11 Warning and Safety instructions In areas which may be subject to infestation by cockroaches or other vermin, pay particular attention to keeping the appliance and its surroundings clean at all times. Any damage caused by cockroaches or other vermin will not be covered by the warranty. Proper installation ...
- Page 12 Warning and Safety instructions Correct use This refrigeration appliance is designed for use within specific ambient temperatures (climate range). Do not use in ambient temperatures for which it is not designed. The climate range is stated on the data plate in the interior cabinet of the refrigeration appliance. A lower ambient temperature will cause the compressor to switch off for longer periods, meaning that the refrigeration appliance is unable to maintain the required temperature.
- Page 13 The surface is susceptible to scratching. Even magnets can cause scratching. Accessories and spare parts Only use original Miele accessories. If other parts are used, warranty, performance and product liability claims will be invalidated. Miele will guarantee to supply functional spare parts for a minimum of 10 years and up to 15 years following the...
- Page 14 Warning and Safety instructions Transport Always transport the appliance in an upright position and in its original transport packaging to avoid damage in transit. Danger of injury and damage to the appliance. The refrigeration appliance is very heavy and must be transported by two people. Disposal of your old appliance ...
- Page 15 Warning and Safety instructions Splashes of coolant can damage the eyes. Be careful not to damage any part of the pipework whilst awaiting disposal, e.g. by - puncturing the coolant channels in the condenser, - bending any pipework, or - scratching the surface coating.
-
Page 16: Caring For The Environment
The packaging materials or with Miele, free of charge. By law, used are selected from materials which you are solely responsible for deleting are environmentally friendly for disposal any personal data from the old and should be recycled. -
Page 17: Installation
*INSTALLATION* Installation This appliance should be installed in a Installation site dry, well-ventilated room. Risk of damage due to high When deciding on the installation site, humidity. please bear in mind that your In environments with high humidity, refrigeration appliance will use more condensation can build up on energy if installed near to a heater, a external refrigeration appliance... -
Page 18: Climate Range
*INSTALLATION* Installation Climate range Ventilation requirements This refrigeration appliance is designed Risk of fire and damage due to for use within specific ambient insufficient ventilation. temperatures (climate range). Do not If the refrigeration appliance is not use in ambient temperatures for which it ventilated sufficiently, the is not designed. -
Page 19: Installing Several Refrigeration Appliances
*INSTALLATION* Installation Installing several refrigeration Changing the door hinging appliances The refrigeration appliance is supplied with hinges on the right. If left-hand Risk of damage due to hinging is required, the hinges must be condensation on external appliance changed. panels. -
Page 20: Fitting Supplied Wall Spacers
*INSTALLATION* Installation Fitting supplied wall spacers Installing the refrigeration appliance The wall spacers supplied must be used in order to achieve declared Risk of injury and damage due to energy consumption values and to the refrigeration appliance tipping prevent the build-up of condensation over. -
Page 21: Aligning The Refrigeration Appliance
*INSTALLATION* Installation Prepare the refrigeration appliance for Aligning the refrigeration appliance installation as close as possible to its Risk of damage and injury intended installation site. caused by the appliance door falling Connect the refrigeration appliance to out or the refrigeration appliance the electricity supply as described in tipping over. -
Page 22: Integrating The Refrigeration Appliance In A Run Of Kitchen Units
*INSTALLATION* Installation Integrating the refrigeration appliance in a run of kitchen units The refrigeration appliance can be surrounded by kitchen units. K(S)/FN(S)/KFN 4xxx X edst/cs, ws, bst, el Top box Refrigeration appliance, door depth = 75 mm Housing unit Wall A = 25 mm (with recessed grip)/60 mm (with handle) Refrigeration appliance with glass front K(S)/FN(S)/KFN 4xxx X bb, brws, bs, grgr... - Page 23 *INSTALLATION* Installation Install the refrigeration appliance next Risk of fire and damage due to to the housing unit. insufficient ventilation. - The appliance front must protrude in If the refrigeration appliance is not front of furniture fronts by at least the ventilated sufficiently, the door depth.
-
Page 24: Appliance Dimensions
*INSTALLATION* Installation Appliance dimensions Installation dimensions/View from above KS 4783 ... edt/cs All dimensions are given in mm. The refrigeration appliance will function correctly if the specified ventilation cross- sections are kept clear. * Dimensions without wall spacers fitted. Appliance depth is increased by 15 mm with the supplied wall spacers fitted. - Page 25 *INSTALLATION* Installation Connections KS 4783 ... edt/cs All dimensions are given in mm. a View from the front b Mains connection cable, length = 2200 mm A longer mains connection cable is available to order from your Miele dealer.
- Page 26 *INSTALLATION* Installation Installation dimensions/View from above FNS 4782 ... edt/cs + KS 4783 ... edt/cs For more information, see the section “Installation – Side-by-side installation” and the installation instructions supplied with the side-by-side installation kit. All dimensions are given in mm. The refrigeration appliances will function correctly if the specified ventilation cross-sections are kept clear.
-
Page 27: Electrical Connection
Miele product must also be overload the cable. maintained in isolated operation or in For safety reasons, do not use an... - Page 28 *INSTALLATION* Installation Connecting the refrigeration appliance Back of the refrigeration appliance Appliance plug connector Mains plug Plug the plug connector into the socket. Make sure that the plug connector has clicked into position correctly. Insert the plug of the refrigeration appliance into the socket.
-
Page 29: Saving Energy
Saving energy How to save energy: Installation The refrigeration appliance has to cool more often at higher site ambient temperatures and consumes more energy in the process. Therefore, you should: - Install the refrigeration appliance in a well-ventilated room. - Do not install the refrigeration appliance near to a heat source (heater element, cooker). -
Page 30: Guide To The Appliance
Guide to the appliance Appliance overview This drawing is for illustration purposes only. - Page 31 Guide to the appliance a Display b Interior lighting c Shelf with egg tray in the appliance door d Fan e Shelves in the appliance door f Adjustable shelf g Split shelf (FlexiBoard) h Bottle shelf with bottle holder i Flexible bottle rack j Space for a baking tray (XL interior) k Compartment lid for setting the humidity level in the DailyFresh drawer l DailyFresh drawer for vegetables (with moisture adjustment)
-
Page 32: Control Panel With Start Display
OK sensor control for confirming a selection d Display for Miele@home connection status (depending on model) (only visible when the Miele@home function has been set up) Settings mode In Settings mode, you can select the following appliance functions and alter their... - Page 33 Guide to the appliance Set up the Miele@home function for the first time, (dependin activate and deactivate WiFi g on or reset the network configuration model) (see “Selecting further settings”) / Switch the keypad tone on or off ...
-
Page 34: Selecting The Desired Function In Settings Mode
Guide to the appliance Selecting the desired function in Settings mode Touch the OK sensor control on the control panel. will appear in the display. Use the or sensor control to scroll to the symbol. Touch OK. ... -
Page 35: Adjusting The Interior Fittings
Guide to the appliance Moving the adjustable shelves Adjusting the interior fittings The shelves can be adjusted according Moving the door shelf/bottle shelf to the height of the food. Only move the door/bottle shelves in the appliance door when they are empty. -
Page 36: Moving The Split Shelf
Guide to the appliance Moving the split shelf Moving the bottle rack To accommodate tall items such as bottles or large containers, the front section of the split shelf slides underneath the rear section. The bottle rack can be placed at different positions in the refrigeration appliance. -
Page 37: Space For A Baking Tray
Guide to the appliance Space for a baking tray Moving the charcoal filters A baking tray can be placed above the KKF-FF charcoal filters with holder drawers. The baking tray can be no (Active AirClean) are available as more than 466 mm wide, 386 mm deep optional accessories (see “Optional and 50 mm high. -
Page 38: Accessories Supplied
6 months. limited to approx. 90°. Bottle rack Optional accessories For a description, see “Guide to the appliance – Adjusting the interior A range of useful Miele accessories and fittings”. care products are available for your appliance. Organisation box Multi-purpose microfibre cloth... -
Page 39: Switching On And Off
The refrigeration appliance adjusts to the electricity supply as described in the preset temperature. “Electrical connection”. To enable the temperature to get Miele will then appear on the appliance sufficiently cold inside the display, followed by . refrigeration appliance, allow the appliance to run for a few hours before placing food in it. -
Page 40: Switching Off For Longer Periods Of Time
Switching on and off Switching off for longer periods of time If, during a long absence, the refrigeration appliance is switched off but not cleaned and the door is left shut, there is a danger of mould building up inside the appliance. It is essential to clean the refrigeration appliance. -
Page 41: The Correct Temperature
The correct temperature ... in the refrigerator section It is very important to set the correct temperature to ensure the shelf life of We recommend a temperature of 4 °C food. Reducing the temperature in the refrigerator section. reduces the growth rate of microorganisms. -
Page 42: Temperature Display
The correct temperature If you change the temperature Temperature display setting: In normal operation, the temperature check the temperature display after a display shows the current average few hours. It will take this long for the refrigerator section temperature appliance to give an accurate inside the refrigeration appliance. -
Page 43: Using Super Cool And Dynacool
Using Super cool and DynaCool Switching SuperCool on and off SuperCool Touch the OK sensor control on the When switched on, the SuperCool control panel. function can be used to rapidly reduce the temperature in the fridge will appear in the display. zone to its lowest setting (depending ... -
Page 44: Switching Dynacool On And Off
Using Super cool and DynaCool Switching DynaCool on and off DynaCool Touch the OK sensor control on the When the DynaCool function is not control panel. switched on, the natural circulation of air in the appliance will cause different ... -
Page 45: Selecting Further Settings
Selecting further settings Holiday mode Explanation of the different settings The Holiday mode function is useful when you go on holiday, for Only the settings that require further example, if you do not wish to switch explanation are described below. off the fridge zone completely or do The door alarm and other warnings not need a high degree of cooling. -
Page 46: Switching On The Lock Function
Selecting further settings Touch the OK sensor control for Switching on the lock function / approx. 6 seconds. When the lock function is switched on, it protects the refrigeration will appear in the display. appliance from being switched off Use the or sensor control to inadvertently and against unintentional scroll to the symbol. -
Page 47: Miele@Home
The ability to use the Miele app - The Miele app depends on the availability of the - A Miele user account You can create Miele@home service in your country. a user account via the Miele app. The Miele@home service is not The Miele app will guide you as you available in every country. - Page 48 Selecting further settings Setting up Miele@home for the first Deactivating or activating the WiFi time connection In Settings mode , use the or In Settings mode , use the or sensor control to scroll to the sensor control to scroll to the symbol.
-
Page 49: Adjusting The Volume Of Alarms And Buzzers
Selecting further settings Adjusting the volume of alarms and Reset the network configuration if buzzers / you are disposing of or selling your refrigeration appliance, or if you are You can adjust the volume of alarms putting a used refrigeration appliance and buzzers (e.g. -
Page 50: Adjusting The Display Brightness
Miele will appear initially in the display, - When reporting an appliance fault to followed by the start screen. your Miele dealer (see “Service”). Touch OK. Charcoal filter change indicator In Settings mode , use the or After inserting the charcoal filter sensor control to scroll to the... -
Page 51: Cleaning Mode
Selecting further settings Cleaning mode Cleaning mode makes it easier to clean the fridge zone (see “Cleaning and care”). The interior lighting remains switched on, even though the fridge zone is switched off. The buzzer will stop and the symbols on the display will also go out. -
Page 52: Door Alarm
Door alarm Switching the door alarm off early The refrigeration appliance is fitted with a warning system to avoid If the alarm disturbs you, it can be increased energy consumption and turned off early. food becoming warm if the appliance ... -
Page 53: Storing Food In The Fridge Zone
Storing food in the fridge zone Different storage zones Risk of explosion due to flammable mixes of gases. Due to natural air circulation, there are Electrical components can cause different temperature regions in the flammable mixes of gases to ignite. refrigerator section. -
Page 54: Food Which Is Not Suitable For Storage In The Refrigerator Section
Storing food in the fridge zone Coldest area Food which is not suitable for storage in the refrigerator The coldest area in the fridge zone is directly above the DailyFresh drawer section and at the back of the appliance. Not all food is suitable for refrigeration at temperatures below 5 °C, because it A temperature setting of 4 °C may be sensitive to cold. -
Page 55: Storing Food Correctly
Storing food in the fridge zone Storing food correctly Ensure that food stored in the fridge zone is in packaging or covered properly (some exceptions apply in the DailyFresh drawer). This will prevent food odours from affecting other food, stop food from drying out and also prevent any cross- contamination of bacteria. -
Page 56: Storing Food In The Dailyfresh Drawer
Storing food in the DailyFresh drawer Selecting low humidity The DailyFresh drawer provides good storage conditions for fruit and The appliance is delivered with vegetables. increased humidity and the The humidity level in the DailyFresh compartment cover pushed drawer can also be regulated to suit the backwards . - Page 57 Storing food in the DailyFresh drawer Observe the following tips if you find that food you have stored does not keep well (e.g. food becomes limp or wilts after only being stored for a short time): Only place fresh food in the appliance. The initial condition of the food is crucial to maintaining freshness.
-
Page 58: Defrosting
Defrosting Fridge zone and DailyFresh drawer The fridge zone and the DailyFresh drawer defrost automatically. Condensate and frost can build up on the back wall of the fridge zone and the DailyFresh drawer whilst the compressor is running. You do not need to remove this. -
Page 59: Cleaning And Care
Cleaning and care Cleaning agents The data plate located inside the interior cabinet of the refrigeration Cleaning and conditioning agents appliance must not be removed. It used in the interior cabinet of the contains information which is required refrigeration appliance must be food in the event of a fault. -
Page 60: Preparing The Refrigeration Appliance For Cleaning
Cleaning and care Preparing the refrigeration Cleaning the inside of the appliance for cleaning appliance Tip: Switch Cleaning mode on. The The refrigeration appliance should be cooling system in the fridge zone is cleaned regularly (at least once a switched off, but the interior lighting month). -
Page 61: Cleaning Accessories By Hand Or In The Dishwasher
Cleaning and care - Adjustable shelves (without the trim Cleaning accessories by hand or printing) or in the dishwasher - The holder for the charcoal filter The following components must be (available as an optional accessory) cleaned by hand only: - The stainless steel trim Removing and dismantling accessories for cleaning... - Page 62 Cleaning and care Dismantling an adjustable shelf Removing the drawers from the fridge zone Before cleaning the shelf remove the stainless steel trim at the front and the protective strip at the back of the shelf. To do this: Place the shelf on a worktop covered with a soft material (e.g.
- Page 63 The symbol in the start display reminds you to replace the charcoal filter. Replacement KKF-RF charcoal filters can be obtained from the Miele Remove the dividing plate. Customer Service Department, from your dealer or from Miele’s website. After cleaning, slide the dividing plate back in again.
-
Page 64: Cleaning The Front Of The Appliance And The Side Panels
Cleaning and care Cleaning the front of the appliance and the side panels If soiling is left on for any length of time, it may become impossible to remove. Surfaces may suffer discolouration or damage. Therefore, it is best to remove soiling from the appliance front and side panels immediately. -
Page 65: Cleaning The Door Seal
(you could inside the refrigeration appliance will use a Miele vacuum cleaner dusting drop quickly. brush, for example). Place food in the refrigeration appliance as soon as it reaches the required coldness. -
Page 66: Problem Solving Guide
Check whether the mains fuse has tripped. There could be a fault with the appliance, the household electrical wiring or another electrical appliance. Contact your Miele dealer. The compressor runs This is not a fault. To save energy, the compressor continuously. - Page 67 Check whether the door seal is damaged. The door seal is No tools are required to change the door seal. damaged and needs to Change the door seal. A replacement is available be replaced. from your Miele dealer.
- Page 68 Problem solving guide Other problems Issue Cause and remedy The floor of the The condensate drain hole is blocked. refrigerator section is Clean the condensate channel and drain hole. wet. There is no audible This is not a fault. The alarm was switched off in alarm even though the Settings mode.
- Page 69 Cause and remedy Demo mode has been activated. lights up on the Touch OK. display, the refrigeration Miele will appear initially in the display, followed by appliance does the start screen. not get cold even Touch OK. though the ...
- Page 70 There is a fault. display, a fault code F To switch the alarm off touch in the display. with numbers appears Contact your Miele dealer. and an alarm also To report the fault you need the fault code and also sounds.
- Page 71 When removing the lighting cover, there is a risk of coming into contact with live electrical components. Do not remove the lighting cover. The LED lighting may only be repaired or replaced by your Miele dealer. Risk of injury from LED lighting.
-
Page 72: Noises
Noises The refrigeration appliance is producing various noises during operation. If the cooling performance is low, the refrigeration appliance will conserve energy but operate for longer. The volume will be lower. Food will be chilled faster if the cooling performance is high. The volume will be higher. -
Page 73: Service
Service Warranty Information to help you rectify faults yourself and about Miele spare parts For more information on country- can be found at www.miele.com/ specific warranty terms and conditions, service. please contact your Miele dealer. Contact in case of malfunction... -
Page 74: Copyrights And Licences
This software/these software components are protected by copyright. The copyrights held by Miele and third parties must be respected. Furthermore, the communication module integrated in the appliance contains software components which are distributed under open source licence conditions. - Page 75 Ramses Extension, 6th Zone, Kuwait Nasr City - Cairo Tel. 00965-22001010 Egypt Fax 00965-24838292 Tel. +202 23480700/15 E-mail: mail@alwazzanunited.com Customer service contact: 15997 Website: www.alwazzanunited.com Fax +202 23426076 E-mail: info@btech.com Website: www.mieleegypt.com Manufacturer: Miele & Cie. KG, Carl-Miele-Straße 29, 33332 Gütersloh, Germany...
- Page 76 KS 4783 ED edt/cs en-SA M.-Nr. 12 124 730 / 00...