FILE NO. Service Manual DVD Player DVD-SL22 (UK) (XE) DVD-SL25 (UK) (XE) PICTURE PICTURE z /ON LAST MEMO OPEN/CLOSE LAST MEMO MODE OPEN/CLOSE MODE PROGRAM PROGRAM /RANDOM REPEAT A-B REPEAT SURROUND /RANDOM REPEAT A-B REPEAT ANGLE ANGLE ON SCREEN ZOOM...
SPECIFICATIONS Playback system: AV EURO CONNECTOR: DVD-Video, CD For Euro-AV/SCART lead Playback standard: VIDEO OUT: PAL or NTSC 1.0 Vp-p (75 Ω) Laser: AUDIO OUT: Semiconductor laser, wavelength: 650/790 nm L: 2 V rms Laser output (Continuous wave max.): R: 2 V rms 1 mW (DVD) Power requirements: 0.5 mW (CD)
DVD MECHANISM REPLACEMENT 1. Cautionary instructions in handling the assy. Do not connect or disconnect roughly by an excessively strong (Safety instructions) force, or a broken wire or bad contact may result. Optical pickup Semiconductors are connected. Do not touch connector terminals The laser beam used in the pickup is classified as "class 2".
MECHANISM REPLACEMENT 1. How to remove the tray. Move both the right and left 1 tray pins to the ends Rotate the 1 gear. Remove the 2 tray. Move forward the 2 tray. 4. How to install the motor. 2. How to insert the tray. SHASSIS HOLE ROUND...
Page 5
MECHANISM REPLACEMENT 5. Base mechanism mounting parts. GREASE EM-30LG GREASE EM-30LG GREASE EM-30LG GREASE EM-30LG : Clean the groove by alcohol well. Apply screw lock 7. Tray parts. 6. Base mechanism parts. GREASE CDF-409 GREASE EM-30LG GREASE CDF-409 GREASE CDF-409 GREASE EM-30LG Do not remove the pick-up from base mechanism because of...
TROUBLE SHOOTING POW ER DO ES NOT TU DOES NOT LI GHT DISPLA Y Is the voltage at lt ag e at Is t h e v Check FL2 line of pi n 1 and 2 of FL 831 Check IC483 and peripheral circ ui t. pin 3 and 5 of CN 81 1 PO WER BLOCK.
Page 7
TROUBLE SHOOTING NO PLAYBACK PICTURE OF COMPOSITE VIDEO OUT NO PLAYBACK PICTURE OFS-VIDEO OUT Check composite signal line Is there VIDEO signal S8400 is S-VIDEO side? Se lect S-VIDEO side. (DAC_D line) and S8400 around. at pin 170 of IC800. Is there VIDEO si gnal at Check DAC_A, DAC_D signal line pin 169 and 170 of IC800?
SERVICE MODE A. Market / Region Setup In the initial condition for this model, Market and Region information are undefined. In the following cases, be sure to set up Market/Region. 1. When updating the system using CD-R (Part code : 0PRADD7118--A). 2.
Page 9
SERVICE MODE C. Setup Procedures 1. Displaying SERVICE MODE screen Display Service Mode screen following the instructions "How to enter Service Mode" above. 2. Displaying Internal Setup screen Push NEXT button within three seconds after operating the Service Mode display. On the Internal Setup screen shown on the right, set up Market and Region.
Page 10
You should check the settings. Backend version S 11225 A 0 Brand (S : SANYO , F : FISHER) Version ( 2 0 0 1 . 12 . 25) Sub Version (A,B,..Z) Region ( 0 : Region undefined...
SERVICE MODE D. IMPORTANT NOTE 1. Once the "Market/Region" settings are written into EEPROM (IC801) on the DVD substrate, they cannot be reset. (However, updating the system using CD-R enables you to make new settings.) 2. While the Internal Setup screen is displayed, pushing the Power button enables you to terminate the operations without making any settings.
PARTS LIST PRODUCT SAFETY NOTICE EACH PRECAUTION IN THIS MANUAL SHOULD BE FOLLOWED DURING SERVICING. COMPONENTS IDENTIFIED WITH THE IEC SYMBOL IN THE PARTS LIST AND THE SCHEMATIC DIAGRAM DESIGNATED COMPONENTS IN WHICH SAFETY AND ! ! ! PERFORMANCE CAN BE OF SPECIAL SIGNIFICANCE. WHEN REPLACING A COMPONENT IDENTIFIED BY , USE ONLY THE ! ! ! REPLACEMENT PARTS DESIGNATED, OR PARTS WITH THE SAME RATINGS OF RESISTANCE, WATTAGE OR VOLTAGE THAT...
Page 14
PARTS LIST REF.NO. PART NO. DESCRIPTION REF.NO. PART NO. DESCRIPTION FL831 645 057 2708 FLOURESCENT TUBE Q8351 405 151 6107 TR KRA107S IC100 409 518 1507 IC LA9703WL-MPB 405 141 5707 TR DTA114YKA IC130 409 531 6107 IC LC78663NRW Q8352 405 151 6107 TR KRA107S 409 514 5004 IC LC78663NW 405 141 5707 TR DTA114YKA...
Page 21
IC BLOCK DIAGRAM & DESCRIPTION IC130 LC78663NRW (DVD/CD Servo Controller) BROCK NAME SUPPLEMENT BLOCK NAME SUPPLEMENT Survo A/D AD1 DVDD1 I/O power supply[Digital 3.3V] Survo A/D AD0 DVSS Digital GND EMPH Survo A/D JV CD data DE-EMP monitor Monitor 0 RREC Survo A/D RREC AVREQI...
Page 22
IC BLOCK DIAGRAM & DESCRIPTION IC131 IS41LV16256-35T (Memory) IC161 BA10358F(Dual Operation Amp) LCAS CLOCK CONTROL CONTROL GENERATOR LOGICS LOGICS UCAS DATA I/O BUS OUT1 CLOCK GENERATOR COLUMN DECODERS -IN1 OUT2 SENSE AMPLIFIERS REFRESH COUNTER 2~5,7~10 I/O0-I/O15 31~34,36~39 +IN1 -IN2 MEMORY ARRAY +IN2 262,144 x 16 ADDRESS...
Page 23
IC BLOCK DIAGRAM & DESCRIPTION IC483 KIA431A(Votage CTL) Cathode Reference 2.5Vref Anode IC490 STR-G6651 (Switching Regulator) START O.V.P LATCH DRIVE REG. Vth(1) O.S.C T.S.D Comp.1 O.C.P/F Vth(2) Comp.2 Pin No. Sym. Description Function MOS FET drain Drain terminal MOS FET source Source terminal Ground Ground terminal...
Page 24
IC BLOCK DIAGRAM & DESCRIPTION IC800 ZR36742PQC (A/V Decoder) Pin No. Name Function Boot selection, debug interface, GPIO pin, test mode (23pin) BOOTSEL1 CPU software starting basis select I. Low:starting by flash memory. High : starting by down loaded program from UART. GPCI/O[0]# I/O# Controled general I/O by microcomputer software.
Page 25
IC BLOCK DIAGRAM & DESCRIPTION IC800 ZR36742PQC (A/V Decoder) Pin No. Name Function Y/R/V YC O : Y signal O. (DAC B) RGB O : R signal O. YUV O : V signal O. C/B/U YC O : C signal O. (DAC C) RGB O : B signal O.
Page 26
IC BLOCK DIAGRAM & DESCRIPTION IC800 ZR36742PQC (A/V Decoder) Pin No. Name Function Loader interface, AV bit stream interface (25pin) ATDD[11]# I/O# ATAPI data I / O. DVDDAT[0] A / V data I. ATDD[4]# I/O# ATAPI data I / O. DVDDAT[1] A / V data I.
Page 27
IC BLOCK DIAGRAM & DESCRIPTION IC800 ZR36742PQC (A/V Decoder) Pin No. Name Function ATCS1# ATAPI chip select signal O. CDCLK# CD-DSP bit clock signal I. GPCI/O[44] Controled general I / O by microcomputer software. ATCS0# ATAPI chip select signal O. CDDAT# CD-DSP data I.
Page 28
IC BLOCK DIAGRAM & DESCRIPTION IC801 AT24C02N-10SI (EEPROM) IC851 PQ070XZ01Z(Regulator) DC INPUT(Vin) DC OUTPUT(Vo) START STOP LOGIC EXCLUSIVE IC SERIAL ON/OFF CONTROL H.V. PUMP/TIMING OUTPUT LOGIC CONTROL (Vc) VOLTAGE LOAD ADJUST (Vadj) DATA RECOVERV COMP DEVICE ADDRESS COMPARATOR LOAD EEOROM DATA WORD ADDR/COUNTER IC859 NC7SZ157P6...
Leakage- current or resistance measurements must be made to determine that exposed parts are acceptably insulated from the supply circuit before returning the product This is a basic wiring diagram. SANYO Electric Co.,Ltd. to the customer. Jan./ '03...