Advertisement
a 19, REMOVE CHASES 3
open the battery « cover.
; : Remove: the six (6) sro
oe 1~6) f for the cabinet back cover, as.
shown | in fig. Ae
. Remove cabinet back cover.
. Pull out sockets from chassis. _
5. Remove
the three (3). 'ef SGIeWS (nos. 1-~~3) for the chassis,
as
_shown in fig. 2.
ce
. Unsolder lead wire. (for the oe cker) from chassis.
. To remove chassis completely unsolder lead wires from cabinet.
so reassemple, evelse ine above procedure.
1D
= To REMOVE DIAL DRIVE ASSEMBLY
eS Remove chassis from cabinet. (Refer to chassis removal
instruc-
tion.)
. Turn tuning shat fille counter- clockwise.
3. Remove band indicator and indicating plate, as shown in fig. 3.
ee Remove the two (2) screws (nos. 2 & 3) for switch, as shown in fig. 3.
- Remove t the four (4) nuts S (10s: 1,4,5 & 6) for volume, as shown in
fig. 3.
|
Remove 'the. six (6) screws (nos. 2, 3, 4, 5, 8 & 2 for diay drive
assembly, as shown in fig. 4.
2 fig. 4.
:
- Remove dial drive gecerbly from hace
_ ings:
—
A, Set variable capacitors to maximum capacity. :
2. Turn tuning shaft fulley counter- -clockwise.
o
DIAL SCALE INSTALLATION
GUIDE
|. Turn tuning shaft fulley counter- elec
ce.
2. Loosen the two (2) screws
(nos. 1 & 6) for the gear, as shown in
fig. 4.
3. Remove spring for the rollers, as shown in fig. 5.
ed
Insert the protuberance of gear in the catch no. 1 of roller no. 2,
as shown in fig. 6.
5. Turn the gear one turn in the direction of arrow, then attach the
stopper
to the catch no. 2 on the roller no. 2, as shown
in fig. 6.
6. Set roller no. 1 at the position as shown
in fig. 5.
. Wind the dial scale onto the roller No. 2, and set it to the dial drive
""*
assembly.
. Set spring at the position as shown
in fig. 5.
. Hook the dial scale on the boss of the roller no. 1, as shown
in fig.
10. Confirm
that the SDpBer of the gear should be located at the
position, as shown in fig. 5. |
11. Set start point of dial scale at the position, as shown
in fig. 7.
12. ger
the two > (2) screws (nos. 1 & 6) for the gear, as shown in
fig 4.
re
:
—
o.oo
Protuberance
—)
Spring
a:
e e
aah
t e s
3
:
:
: Z|
Roller No.2
2
3
i
:
Sit
Catch No.1
2
= Ml :
2
=
|
Catch No.2
3
=
Z
Z
=
haa]
RollerNo2:
0...
Seale
Stopper
Fig. 6
| A2
RF-1115 /o
a Loosen the two. 2) Screws (nos. 7 & 9) for UHF tuner, as shown in
10 reassemble, reverse the above Po
and note the follow:
Gear
yom"
ee
- -ScrewNo.3
(XTB3+45Bi
"Serew No:1
Screw
No.2
see
COW No.6
o
(XTB3+45BFN).
Screw Noo. ots
(XTB3-+408FN) a
Fig. A
—(XTB3+458FN)
Red Screw No.1
Red Screw N
(XTN3+12CR)
Red Screw No.2
oe
OS
en)
:
~OCTNG-HI6CR)
roe
~~ ScerewNo.3
NutNot
Screw No.2
(XTW3+10F)
(XNS8) _
(XTW3+10F)
Band Indicator
:
ooo
Nut No.6s.
(XNS8) |
(XNS8)
me
(XNS8) Bo
Fig. 3
Screw No.5
(XTN3-+ 100)
Screw No.1
Screw No.2
Shrew No.3 .
Screw No.4
(XXARSH6S).-
(XTW3+10F)
(XTW3-+10F):(XTW3-++10F)
:
/
: Screw No.8
Sarew No.9.
Screw No,10:°
(XTN3+ 100)
(XXAR3H6S)
(XTN3+ 100)
Screw No.6.
Sorew No.7
(XXAR3H6S) (XXAR3H6S)
Fig. 4
~~ Start Point
1
Mi
Boss
NO
Advertisement
