1. Manuals
  2. Brands
  3. Panasonic Manuals
  4. Camera Lens
  5. Lumix S-R70300
  6. Service training manual

Panasonic Lumix S-R70300 Service Training Manual

Hide thumbs Also See for Lumix S-R70300:
Table of Contents

Advertisement

Quick Links

Download this manual
Service Training Manual
Specifications
INTERCHANGEABLE LENS FOR DIGITAL CAMERA "LUMIX S 70-300 mm F4.5-5.6"
Mount
Focal length
Lens construction
Aperture type
Maximum aperture
Minimum aperture value
Angle of view
In focus distance
Maximum image magnification
Optical Image stabiliser
Filter diameter
Maximum diameter
Overall length
Mass (Weight)
Dust and splash resistant
Recommended operating
temperature
Permissible relative humidity
S-R70300
Component Repair
Leica Camera AG L-Mount
f=70 mm to 300 mm
17 elements in 11 groups (1 UED lens, 2 ED lenses, 1 UHR lens)
11 diaphragm blades/Circular aperture diaphragm
F4.5 (Wide) to F5.6 (Tele)
F22
34°(Wide) to 8.3°(Tele)
[FULL]: 0.54 m (1.77 feet) to ∞ (Wide)/0.74 m (2.43 feet) to ∞ (Tele)
(from the focus distance reference line)
[3m-∞]: 3.0 m (9.84 feet) to ∞ (from the focus distance reference line)
0.5× (focal length 300 mm)
Yes
77 mm
Φ84 mm (3.3 inch)
Approx. 148.0 mm (5.8 inch)
(from the tip of the lens to the base side of the lens mount)
Approx. 790 ｇ (1.75 lb)
Yes
－10 ℃ to 40 ℃ (14 ℉ to 104 ℉)
10%RH to 80%RH
ⓒ Panasonic Corporation 2021 Unauthorized copying and distribution is a violation of law.
Ver.1.0
Internal use only

Advertisement

Table of Contents
loading

Related Manuals for Panasonic Lumix S-R70300

Summary of Contents for Panasonic Lumix S-R70300

  • Page 1 Approx. 790 ｇ (1.75 lb) Dust and splash resistant Recommended operating －10 ℃ to 40 ℃ (14 ℉ to 104 ℉) temperature Permissible relative humidity 10%RH to 80%RH ⓒ Panasonic Corporation 2021 Unauthorized copying and distribution is a violation of law.

  • Page 2: Table Of Contents

    TABLE OF CONTENTS PAGE 1 Service Navigation ・　・　・　・　・　・　・　・　・　・ 1.1. Introduction ・　・　・　・　・　・　・　・　・　・ 1.2. Important Notice ・　・　・　・　・　・　・　・　・　・ 1.2.1. Overview of Cleaning and Replacing parts ・　・　・　・　・　・　・　・　・　・ 1.2.2. How to treat LENS MAIN UNIT (Ref. No. 220) ・　・　・　・　・　・　・　・　・　・ 2 Exploded View ・　・　・　・　・　・　・　・　・　・ 2.1. Exploded View of Lens Unit ・　・　・　・　・　・　・　・　・　・...

  • Page 3: Service Navigation

    1 Service Navigation 1.1. Introduction This manual contains technical information, which allow service personnel's to understand and service this model. Please place an order using the parts list and not the drawing reference numbers. 1.2. Important Notice Perform lens cleaning and repair in the clean room (class 10,000) since lens is delicate product and it dislikes a dust. 1.2.1.

  • Page 4: How To Treat Lens Main Unit (Ref. No. 220)

    1.2.2. How to treat LENS MAIN UNIT (Ref. No. 220) 1. LENS MAIN UNIT (Ref. No. 220) is not eligible for service part, use LENS UNIT (Ref. No. 200) instead. 2. Reuse SHADING FRAME (Ref. No. 209) because it put serial number. B225 B224 B226...

  • Page 5: Exploded View

    2 Exploded View 2.1. Exploded View of Lens Unit B225 B224 B226 B203 B202 B204 B201 B205 B206 B228 B232 B227 B229 B231 B230 B221 B222 B214 B215 B217 B218 B216 B223 B211 B220 B219 B210 B212 B207 B213 B209 B208 2.2.

  • Page 6: Replacement Parts

    3 Replacement Parts ・All parts are supplied from PAVCX Ref.No. Part No. Part Name & Description Remarks DVQL1138Z CE/WEEE LABEL VQL1W22 TEN YEARS LABEL 1 GK LOU5SR70300CSFCZ LENS UNIT MDE2Z294Z DECORING UNIT DVOR1095Z FILTER RING DVHG1247ZKIT ZOOM RING RUBBER KIT 6SE4SS85Z MOUNT CONTACT UNIT KDE4Z294Z...

  • Page 7: Service Jigs & Tools

    600mm x 800mm Rp-Chart M-size SUKZ000035 300mm x 400mm Lens Cleaning Kit VFK1900BK Collimeter RFKZ0422 Master Body Purchased locally DC-S1R (Panasonic) Tweezers Purchased locally Plastic or bamboo (Do not use metal) Nipper Purchased locally Tripod Purchased locally Locking glue Purchased locally...

  • Page 8: Maintenance

    5 Maintenance 5.1. Dust / Dirt on the outer casing part(s) 1. Blow off the dust first, then sweep out the dust from narrower spaces with soft cleaning brush. 2. Wipe up the outer casing part with the dry fuzz-free cloth. 5.2.

  • Page 9: Disassembly And Assembly Procedures

    6 Disassembly and Assembly Procedures 6.1. Disassembly Procedures 6.1.1 Disassembly Flowchart Lens Unit 1 Shading Frame 2 L Mount Mount Rubber Rear Frame Unit Mount Contact Unit Lens P.C.B. Unit Attention For optical axis adjustment only,perform No.5 and No.6. 5 Decoring Unit Filter Ring Adjustment Screw 8 Zoom Ring Rubber...

  • Page 10: Disassembly Procedure

    6.1.2. Disassembly Procedure Important Notice： Perform lens disassembly in the clean room (class 10,000/ Federal Standard 209D) since lens is delicate product and it dislikes a dust. 6.1.2.1. Removal of Shading Frame 1. Remove 3 screws (A) and Shading Frame. Shading Frame Screw (A) ｘ...
  • Page 11 6.1.2.3. Removal of Mount Rubber and Rear Frame Unit 1. Remove Mount Rubber. 2. Remove 4 screws (D) and Rear Frame Unit. Mount Rubber Screw (D) Screw (D) ｘ 4 Rear Frame Unit 6.1.2.4. Removal of Mount Contact Unit 1. Disconnect 5 connectors of Lens P.C.B. Unit. Connector ｘ...
  • Page 12 6.1.2.5. Removal of Decoring Unit 1. Decoring Unit is sticked on Filter Ring. 2. Put the sheet so that the lens glass is fullty covered. 3. Insert the small flat blade screwdriver to Gap (between Decoring Unit and lens glass), and peel off Decoring Unit gently. 6.1.2.6.
  • Page 13 6.1.2.7. Removal of Adjust Screw and 1st Lens Frame Unit 1. Peel off the tape and Remove glue around 3 Adjustment Screws. ※ Be careful the dust don't enter in Lens Unit. Adjustment Screw Adjustment Screw 2. Mark the current position of Adjustment Screw in a horizontal straight line. Horizontal Straight Line ※...
  • Page 14 6.1.2.8. Removal of Zoom Ring Rubber 1. Pull Zoom Ring Rubber off and cut by scissors a little. Note: Don't tough Lens Unit to avoid the scratch or damage. 2. Tear Zoom Ring Rubber by hands and remove from Lens Unit. Note: Zoom Ring Rubber is fixed by adhesive.
  • Page 15 2. Remove 5 screws (H). 3. Remove Ring Mount Base Unit. Screw (H) Rjng Mount Base Unit Screw (H) ｘ 5 6.1.2.10. Removal of 3-7 Cam Pin and 7th Lens Frame Unit 1. Remove 3 screws (J) and 3 Cam Pin. Screw (J) &...
  • Page 16 3. Remove 7th Lens Frame Unit. 7th Lens Frame Unit...

  • Page 17: Assembly Procedure

    6.2. Assembly Procedure 6.2.1 Assembly Flowchart 1st Lens Frame Unit 7th Lens Frame Unit Adjustment Screw 3-7 Cam Pin Ring Mount Base Unit Zoom Drive Pin 4 Zoom Ring Rubber Mount Contact Unit Lens P.C.B. Unit Rear Frame Unit Mount Rubber 7 L Mount 8 Shading Frame Attention...

  • Page 18: Assembly Procedure

    6.2.2. Assembly Procedure Important notice： When tightening the screw, use a torque driver (RFKZ0542) with specified torque described in each step. 6.2.2.1. Installation of 1st Lens Frame Unit and Adjust Screw 1. Install 1st Lens Frame Unit. 2. Insert Adjustment Screw using a nipper with a fine tip since the screw is small. 1st Lens Frame Unit Adjustment Screw 3.
  • Page 19 6.2.2.2. Installation of 7th Lens Frame Unit and 3-7 Cam Pin 1. Install 7th Lens Frame Unit. 7th Lens Frame Unit 2. Install 3-7 Cam Pin and tighten 3 screws (J) by using the torque driver with specified torque. Screw (J) ①...
  • Page 20 6.2.2.3. Installation of Ring Mount Base Unit and Zoom Drive Pin 1. Install Ring Mount Base Unit as shown in the figure while pulling out the FPC via the Hole. 2. Tighten 5 screws (H) in numerical order by using the torque driver with specified torque. ②...
  • Page 21 6.2.2.4. Installation of Zoom Ring Rubber 1. Stick new Zoom Ring Tape to Lens Unit. While pulling a Tape, stick Tape little by little with pressing out air bubble. Caution： a. Remove all dust from Lens Unit. b. Avoid air or air bubble between Tape and Lens Unit. Remove all dust from Lens Unit. c.
  • Page 22 6.2.2.5. Installation of Mount Contact Unit. 1. Connect FPC of Mount Connect Unit to connector. 2. Installation Lens P.C.B. Unit with Mount Contact Unit. 3. Tighten 3 screws (E) in numerical order by using the torque driver with specified torque. Lens P.C.B.
  • Page 23 6.2.2.6. Installation of Rear Frame Unit and Mount Rubber 1. Install Rear Frame Unit. 2. Tighten 4 screws (D) in numerical order by using the torque driver with specified torque. 3. Install Mount Rubber. ① Mount Rubber ② Screw (D) ④...
  • Page 24 6.2.2.8. Installation of Shading Frame 1. Install Shading Frame. 2. Tighten 3 screws (A) in numerical order by using the torque driver with specified torque. Shading Frame ② ① ③ Screw (A) ｘ 3 Screw (A) ① → ② → ③ Screw Order Torque 10.0 ±...
  • Page 25 6.2.2.9. Installation of Filter Ring 1. Install Filter Ring. 2. Tighten 6 screws (F) in numerical order by using the torque driver with specified torque. ⑥ ① ⑤ Screw (F) ② ④ ③ Filter Ring Screw (F) ｘ 6 ① → ② → ③ → ④ → ⑤ → ⑥ Screw Order Torque 10.0 ±...
  • Page 26 6.2.2.10. Installation of Decoring Unit 1. Insert 3 Pins of Decoring Unit to 3 Holes of Filter Ring. ・Use new one, do not use the one which is removed. ・Double-stick tape sticks to Decoring Unit of the repair part. Remove the old double-stick tape from Filter Ring. 2.

  • Page 27: Adjustment

    7 Adjustment 7.1. Matrix Table of Necessary Adjustment when Replacing Parts The table shows necessary adjustment when replacing parts. Necessary Adjustment Replacement Part Simple Resolution Electrical Real Time Adjustment Adjustment - - - DECORING UNIT - - - - - - FILTER RING - - - - - -...

  • Page 28: Flowchart Of Adjustment

    7.3. Flowchart of Adjustment Check for Defective Parts and Internal Dust Disassembly Replacement or Cleaning Assembly Setting to Simple Resolution Real Time Adjustment - Check the brightness TELE end and settings of camera - Begin again after Simple Resolution body and test chart disassembly/assembly Real Time - Begin again after...

  • Page 29: Procedure Of Adjustment

    7.4. Procedure of Adjustment 7.4.1. Equipment and Chart Setting (2) Checking Chart (5) Monitor HDMI cable USB cable (1) LED lamps (4) Capture Board (6) PC Software (3) Lens and Master Body(DC-S1R) Install LED lights left and right symmetrically as uneven illumination does not occur.

  • Page 30: Checking Chart Image

    7.4.2. Checking Chart Image <Preparation> - Checking Chart (Part No. SUKZ000059) that consisted of 5 charts No.1 - No.5. and 4 black charts. - White plastic matte board /Size: 1,440mm(W) x 960mm(H) or above Guide Line - Length: 500mm or more - Thickness: 5mm or more No.2 No.5...

  • Page 31: Master Body(Dc-S1R) Setting And Position

    7.4.3. Master Body(DC-S1R) Setting and Position 7.4.3.1 Master Body(DC-S1R) Setting - Cancel the Initial Setting - Set the function parameter to below setting Setting Item Setting value Mode dial A (Aperture-Priority AE Mode) Aperture F 4.5 (Wide) – F5.6 (Tele) 【S】([AFS]) Focus mode Image stabilizer...
  • Page 32 For more accurate checking, hang the hand glass installed from the upper part of the center of the Checking Chart to the string down, and adjust it to come to the chart center. And If the lens of oneself reflecting in the mirror is displayed in the center of the LCD monitor, placing is correctly.

  • Page 33: Lens Unit Setting

    7.4.4. Lens Unit Setting - Set the function parameter to below setting Setting Item Setting value Focus switch [FULL] AF/MF switch O.I.S. switch 7.4.5. PC Software 7.4.5.1 Required PC Specification - OS ： Windows 10 - Processor ：Pentium 4/M or equivalent - Memory ：512 MB RAM - Display...

  • Page 34: Simple Resolution Real Time Adjustment

    7.4.6. Simple Resolution Real Time Adjustment Simple Resolution Real Time Adjustment is useful for models which have adjustment screws in 1st Lens Frame Unit. Results are shown in real time, by rotating Adjustment Screws by using Torx Driver (RFKZ0609). ※ Check the visual of Chart on the monitor. 1st Lens Frame Unit Torx driver (RFKZ0609) Adjustment Screw...

  • Page 35: Electrical Adjustment

    7.4.7. Electrical Adjustment Make Electrical Adjustment using PC with Adjustment Software. As for Adjustment conditions/procedure, consult the "Adjustment Manual" which is available in Adjustment Software. Note: - Download the software package from TSN. - The first time to implement all item - The second time to implement the only BF Adjustment 7.4.8.
  • Page 36 RP Chart L-Size 600x800mm (SUKZ000034) RP Chart M-Size 300x400mm (SUKZ000035)

  • Page 37: Revision History

    8 Revision History Ver. Date History 2021.06.25 ・First Issue...

Table of Contents