Advertisement
1 Weofor-htrelaW-latoM alejaleiiolame) m@xelalige) (-)
Front Panel Remote Commander
(Side panels are provided only on the Canadian model.)
|
1
2
3
4i15)(6}(7}18
Seer
r-)
OMB
Gi
11
A
Pull this knob to open
the control panel.
POWER switch
Turns the power on and off.
Cassette compartment
insert a Cassette with the window side up and the
safety tab facing you
Display window
Remote sensor
Receives the signal from the remote commander.
SBM (Super Bit Mapping) switch and indicator
Set to ON for Super Bit Mapping during analog
recording through the LINE IN jacks in STANDARD
recording mode (REC MODE selector)
SBM indicator lights when the SBM function is on
(applicable during analog recording only)
COUNTER MODE button
Selects the display of the absolute time, elapsed time
of the current selection, remaining time to the end of
whole tape or linear counter (tape running time). Each
time you press the button, the display changes
sequentially.
INPUT selector
Set according to the signal to be recorded.
ANALOG: For recording from the equipment
connected to the LINE IN jacks
OPTICAL: For recording from the equipment
connected to the DIGITAL IN (OPTICAL) jack.
COAXIAL: Far recording from the equipment
connected to the DIGITAL IN (COAXIAL) jack
12)
REC LEVEL (recording level) controls
Adjust the recording levels and balance for the analog
input signals.
The outer knob controls the L (left) channel level and
the inner knob the R (right) channel level. The knobs
can be adjusted together. To adjust each channel
independently, turn the knob while hoiding the other
knob
When recording digitai signais, it is not necessary to
adjust the recording levels
REC MODE selector
Normally set to the STANDARD position.
When this selector is set to the LONG position, you
canrecord analog input signals or digital signals with
32 kHz in the long-play mode
PHONES-LEVEL jack and contro!
insert the headphones plug to this jack and turn the
control to adjust the headphones
volume level
11)
TIMER switch
Normaily set to the OFF position. When recording or
playing back at the desired time using a commercially
available audio timer, set to the REC position or the
PLAY position respectively.
Numeric buttons (0 - 9)
Designate the desired program number to be played
back before starting playback. Designate the desired
number in the record-pause mode, the program
number is written consecutively from the designated
number
3
MUSIC SCAN button
Press to listen to the beginning of each selection
successively
FADER button
Press to fade in or fade out during recording or
playback
MARGIN RESET button
Press to reset the margin of peak level
END ID buttons
WRITE: Press to write the ID signifying the end of
Playback or recording
ERASE: Press to erase the end !D.
SKIP ID buttons
WRITE: Press at the beginning of the portion you may
wish to skip later. A skip ID will be written from the
point where you pressed this button
ERASE: Press to erase the nearest skip |D which is
before the current position
START ID buttons
AUTO: Press to turn on and off the AUTO indicator.
When the AUTO indicator is lit, the start ID will
automatically be written during recording. When the
AUTO indicator is not lit, press the START ID WRITE
button at the point where you want to write a start ID
WRITE: Press to write the start iD at the desired point
during recording or playback.
ERASE: Press to erase a start ID. When a start ID and
a program
number
are written on the tape, both
codes are simultaneously erased by pressing this
button
RENUMBER: Press to renumber all programs on the
tape. When only the start IDs are written, pressing
this button will insert the proper program numbers
beginning with "1". The tape will rewind and start
from the beginning to accomplish this function
CLOCK SET button
Press to adjust the time of the clock built in this unit.
In this mode, the 0 button and the 9 button function as
the + and — buttons respectively
PRESENT button
Press to display the current time
Each time the RECORDED or PRESENT button is
pressed, day, month and year display, the day of the
week display or hour, minute and second display is
switched sequencially.
RECORDED button
Press to display the recording day of the tape being
played
CLEAR button
Press to cancel the program number which has
been mistakenly entered.
'yenuew
uorjonajsur
woay
TWHANID
L NOILOAS
|
pa}e1yx9
st UOT}I—S
SIYT,
Advertisement
