Advertisement
If you have questions or comments, contact us. |
1-800-4-DEWALT www.dewalt.com |
The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols.
Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
Used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in property damage.
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL, CALL US TOLL FREE AT:
1-800-4-DEWALT (1-800-433-9258)
DW7440RS Rolling Table Saw Stand with Folding Legs
For your own safety, read the table saw instruction manual before using any accessory. Failure to heed these warnings may result in personal injury and serious damage to the table saw and the accessory. When servicing this tool, use only identical replacement parts.
This stand is designed for use with table saws only. The DW7440RS is approved for use with the DW744, DW744X and the DW745 table saws. If you experience a problem with your DEWALT purchase, please call 1-800-4-DEWALT (1-800-433-9258).
Phillips screwdriver
Socket or wrench set
Stand
Mounting brackets (2)
Wheels (2)
Rubber bumpers (2)
Washers (4)
Kickstand assembly
Tube plugs (2)
Carriage head bolts (2)
M8 lock nuts (4)
Rear axle M4 screws (2)
M4 lock nuts (2)
M6 screws (4)
M4 hex wrench
Saw mounting hardware: hex head bolts (4), washers (8), nuts (4), lock washers (4)
Insert the tube plugs (O) into the end of the kickstand tube (N). The groove in the tube plug should be facing down as shown. Be sure that the holes (P) in the tube plugs are in line with the holes (Q) in the kickstand tube before inserting the tube plugs.
Insert the kickstand tube (N) through the holes in the leg support (B) on the wheel-axle side of the stand. Be sure the kickstand is pointing up when the stand is an upright position. Secure the kickstand to the beams (I) with the four M6 screws provided as shown (below, left).
The hex wrench may be stored in the end of the tube plug as shown for future use.
Attach the two rubber bumpers (M) to the handle side leg support as shown using the M4 screws and lock nuts provided.
To reduce the risk of injury, turn unit off, disconnect machine from power source before assembling the table saw to the table saw stand. An accidental start-up can cause injury.
For your own safety, read and understand the table saw instruction manual before using. Failure to heed these warnings may result in personal injury and serious damage to the table saw and the accessory.
The saw mounting brackets provided with this stand are equipped with lever locks. To reduce the risk of injury, DO NOT modify the mounting bracket lever locks.
To reduce the risk of personal injury, be sure the table saw is fully anchored on the stand.
The table saw must be positioned on the tool mount so that all four corners can be bolted to the mounting brackets. If the saw is mounted properly, the mounting brackets will be positioned perpendicular to the stand rail when the saw is placed on the stand.
Please call DEWALT customer support at 1-800-4-DEWALT if you need assistance.
To reduce the risk of injury, turn unit off, disconnect machine from power source before detaching the table saw from the table saw stand. An accidental startup can cause injury.
The saw mounting brackets included with the DW7440RS stand are equipped with rubber feet that can support the saw E when cutting on a work area without a stand.
To reduce the risk of personal injury, NEVER use the table saw with the handle extended. An extended handle creates an unsafe work area.
To reduce the risk of personal injury, do not hang objects from the handle. The stand may tip when downward force is applied.
To reduce the risk of personal injury, DO NOT operate the table saw mounted to the stand with the legs folded and the stand sitting on the ground.
Roll the stand to the workspace. Be sure the area is flat and stable before attempting to set up the saw and stand.
Since accessories, other than those offered by DEWALT, have not been tested with this product, use of such accessories with this tool could be hazardous. To reduce the risk of serious injury, place stand on flat, stable surface. DO NOT create unstable conditions.
Recommended accessories for use with your tool are available at extra cost from your local dealer or authorized service center. If you need assistance in locating any accessory, please contact DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286, call 1-800-4-DEWALT (1-800-433-9258) or visit our website www. dewalt.com.
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustments should be performed by a DEWALT factory service center, a DEWALT authorized service center or other qualified service personnel. Always use identical replacement parts.
To reduce the risk of personal injury:
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call 1-800-4-D E WALT for a free replacement.
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Advertisement
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the DW7440RS that isn't answered in the manual? Leave your question here.