Sound Setup - Yamaha HTR-6260 Owner's Manual

Crossover Freq.
40Hz/60Hz/80Hz*/90Hz/100Hz/110Hz/120Hz/
Choices:
160Hz/200Hz
Sets the lower limit of the low frequency component
output from a speaker with a size set to "Small (SMLx1/
SMLx2)." Sound with a frequency below that limit is
output from a subwoofer or front speakers.
If your subwoofer has a volume control or a crossover
frequency control, set the volume to half or the crossover
frequency at the maximum.
Subwoofer Phase
Choices: Normal*/Reverse
Sets the phase of your subwoofer if bass sounds are
lacking or unclear.
Normal
Select this not to change the phase of your
subwoofer.
Reverse Select this to reverse the phase of your
subwoofer.
■
B)Level
Adjustable range: -10.0dB to +10.0dB (0.5 dB step)
"FR.L/FR.R/SWFR" 0dB
Defaults:
"CNTR/SUR.L/SUR.R/SBL/SBR" -1.0dB
Separately adjusts volume of each speaker so that the
sounds form speakers are at the same volume at the
listening position. Items to be displayed vary depending
on the number of speakers connected.
y
• When only one surround back speaker is connected, "SB" appears
instead of "SBL" and "SBR."
• You can adjust the volume listening to test tones when you set "Test
Tone" to "On" (see page 53).
• If your subwoofer has a volume control or a crossover frequency control,
set the volume to half or the crossover frequency at the maximum.
■ C)Distance
Adjusts timing at which each speaker outputs sound so
that sounds from speakers reach the listening position at
the same time. Set unit (Unit) first and set the distance of
each speaker.
Unit
Choices: meters (m)/feet (ft)*
meters (m) Displays the speaker distance in meters.
feet (ft)
Displays the speaker distance in feet.
Front L Front R
/
Sur. R Sur.B L Sur.B R
/ /
L PRNS R
/
Adjustable range: 0.30m to 24.00m (1.0ft to 80.0ft)
3.00m (10.0ft) "Front L/Front R/
Defaults:
SWFR"
2.60m (8.5ft) "Center"
2.40m (8.0ft) "Sur. L/Sur. R/
Sur.B L/Sur.B R/PRNS L/PRNS R"
y
• Different items are displayed depending on settings of "A)Config" (see
page 51).
• When only one surround back speaker is connected, "Sur.B" appears
instead of "Sur.B L" and "Sur.B R."
Center Sur. L
/ / /
SWFR PRNS
/ /
Operating various settings for this unit (Setup menu)
■ D)Equalizer
Adjusts sound quality and tone using a parametric graphic
equalizer.
EQ Type Select
Choices: Auto PEQ/GEQ*/Off
Select an equalizer type.
Auto PEQ Uses a parametric equalizer selected in
"1 Auto Setup." Characteristics of the
currently used parametric equalizer (see
page 19) are displayed below "Auto PEQ."
If Auto Setup is not executed, this
parameter is not displayed.
Uses a graphic equalizer. Press oENTER
GEQ
to adjust the characteristics of the graphic
equalizer.
Off
Not use a graphic equalizer.
GEQ
Choices: 63Hz/160Hz/400Hz/1kHz/2.5kHz/
6.3kHz/16kHz
Adjustable range: -6.0dB to 0dB* to +6.0dB (0.5 dB step)
Adjusts sound quality of each speaker using a graphic
equalizer. The graphic equalizer of this unit can adjust
signal levels in 7 frequency ranges.
To adjust the signal level within each range, select the
desired speaker with oCursor l / h while "→" is
displayed next to "Channel," then the desired frequency
band with oCursor k / n, and adjust the signal level
with oCursor l / h.
■
E)Test Tone
Choices: Off*/On
Switches between on and off of an oscillator that generates
test tones. To turn on the oscillator, select "On" using
oCursor l / h. When "On" is selected, you can adjust
the settings of "2 Manual Setup" while listening to a test
tone.
Off
Not generate test tones.
On
Generates test tones.

Sound Setup

You can set various items for sound outputs.
■
1 Dynamic Range
Choices: Min/Auto/STD/Max*
Selects the dynamic range adjustment method for
reproducing bitstream signals.
Min/Auto (Min) Sets the dynamic range suitable for
low volume or a quiet environment, such as
at night, for bitstream signals except for
Dolby TrueHD signals.
(Auto) Adjusts the dynamic range for Dolby
TrueHD signals based on input signal
information.
STD
Sets the standard dynamic range
recommended for regular home use.
53
En