Advertisement
Model No:
BC1000.V3
Capacity:
1000Kg
A
230mm
B
180-360mm
C
64mm
D
5mm
E
215mm
F
102-155mm
G
25mm
H
Ø22mm
W.L.L
1T
2T
3T
5.
INSTALLATION
5.1.1. Open the clamping jaws by rotating the lever counter
clockwise.
5.1.2. Position the beam clamp on the beam.
5.1.3. Close the clamping jaws by rotating the lever clockwise until
hand tight.
5.1.4. Check that the clamping jaw seat has engaged the beam
fully.
5.1.5. Ensure the hoist or sling being attached to the beam clamp is located directly under the centre line of both the beam and the beam
clamp.
6.
OPERATION
6.1.
(Refer to Section 6.2 regarding inspection and examination before each and every use).
6.2.
APPLYING A LOAD
6.2.1. Do not wrap the hoist rope or chain around the load.
6.3.
Attach the load to the load hook securely by properly rated, suitable means, such as chains, shackles, hooks, lifting slings, etc. Load must
be attached to prevent accidental disconnection.
DO NOT operate the hoist unless rope or chain is seated properly on the drum, sheaves, or sprockets.
8
DO NOT operate the hoist unless the hoist unit is centered over the load.
8
DO NOT pick up a load in excess of the rated load appearing on the hoist or load block, except during properly authorised tests.
8
DO NOT use a hoist overload limiting device to measure the maximum load to be lifted.
8
6.4.
Give specific attention to load balancing and hitching or slinging to prevent load slipping.
6.4.1.
Attach to a suitably rated beam that is capable of withstanding a load of at least 1½ times the beam clamps safe working load, open the
jaws of the beam clamp to the required width, slide the beam clamp onto the beam and secure by tightening the locking lever, connect the
beam clamp to the load using a suitably certified sling or block. Ensure you are aware of the load weight, and check that it is within
the capacity of the beam clamp and the sling/block or support beam.
WARNING! DO NOT lift the load at an angle.
‰
WARNING! Use only on beam widths that are within the adjustable limits of the beam clamp.
‰
DO NOT exceed the W.L.L of the beam clamp. See table above.
8
DO NOT use a beam clamp which is damaged or deformed.
8
DO NOT attemp to repair a damaged beam clamp. It must be repaired by an authorised repair agent.
8
DO NOT stand under load or installed beam clamp.
8
Do inspect the beam clamp after every use.
9
WARNING! This product must be only used by suitably trained persons.
‰
DO NOT engage in any activity which will divert the operator's attention while operating the hoist.
8
6.4.2. Respond to signals from a designated person only. However, always obey a stop signal, no matter who gives it.
DO NOT lift or lower a load with the hoist until the operator and all other personnel are clear of the load.
8
DO NOT lift a load more than a few inches until it is well balanced in the sling or lifting device.
8
WARNING! DO NOT carry personnel on the hook or the load.
‰
DO NOT leave a suspended load unattended unless specific precautions have been instituted and are in place.
8
7.
MAINTENANCE
NOTE: The beam clamp MUST be kept clean and dry and must be maintained in accordance with these instructions.
7.1.
LUBRICATION
7.1.1. Oil threads and hinged parts monthly or when necessary.
7.1.2. Always lubricate threads and hinged parts before storing the beam clamp.
7.2.
INSPECTION AND EXAMINATION OF CLAMP BEFORE USE
7.2.1. Before each use of the beam clamp you must perform an inspection for damage, loose or missing parts.
© Jack Sealey Limited
BC2000.V3
BC3000.V3
2000kg
3000Kg
230mm
320mm
180-360mm
235-490mm
74mm
103mm
6mm
8mm
215mm
260mm
102-155mm
140mm
25mm
45mm
Ø22mm
Ø24mm
SUITS BEAM WIDTH MM
75-230
75-230
80-320
Original Language Version
Beam
Clamping jaw
BC1000.V3, BC2000.V3, BC3000.V3, Issue:2 27/02/24
fig.1
Clamping jaw set
Threaded spindle
Lever
Loading bar
Advertisement
