Ceiling Mount Bracket PMT-L31 (for Low Ceilings) PMT-H35 (for High Ceilings) Installation Manual Be sure to read this manual thoroughly before using this bracket. After you have read this manual, retain it for future reference. When installing the projector using this...
SAFETY INSTRUCTIONS 1. Always follow the instructions set forth in this manual when installing the projector using this bracket. Improper or inadequate installation could cause the projector to fall and injure someone. 2. The installation must be secure enough to bear the weight of the projector, the ceiling bracket, and other hardware indefinitely, and must also be secure enough to withstand vibration.
Page 3
9. Never hang from the projector or the ceiling bracket. Hanging from the projector or the ceiling bracket could cause the projector or the ceiling bracket to fall and injure someone. 10. Do not install the projector in a location near an air conditioning vent or in a location subject to vibration.
Common parts (The following parts are provided with each bracket.) Projector mounting adapter x 1 Safety brackets x 2 Safety wires x 2 PMT-H35 Ceiling bracket x 1 Adjustment pole locking screws (M5) x 4 Projector mounting screws (M6, pan head) x 4...
NAMES OF PARTS PMT-L31 Mounting guide pin Vertical angle adjustment screws (There are also screws on the opposite side.) Horizontal angle adjustment screws Ceiling bracket Projector mounting adapter Tilt angle adjustment screws (There are also screws on the opposite side.)
Page 6
PMT-H35 Ceiling bracket Height locking screw Height adjustment pole Mounting guide pin Vertical angle adjustment screws (There are also screws on the opposite side.) Horizontal angle adjustment screw (four in total) Projector mounting adapter Tilt angle adjustment screws (There are also screws on the...
[Front View] 10° 10° 495 mm (19-1/2 inch) with the DPX-1000 installed [Top View] 120 mm (4-3/4 inch) 156 mm (6-1/8 inch) PMT-H35 [Front View] 495 mm (19-1/2 inch) with the DPX-1000 installed [Top View] (8-5/16 inch) Projection direction (6-13/16 inch)
2.2 to 3.5 [7.2 to 11.5] 2.75 to 4.4 [9 to 14.4] 3.3 to 5.3 [10.8 to 17.4] 5.5 to 8.8 [18 to 28.9] Distance from ceiling surface to center of lens: PMT-L31: Approx. 26 cm 120" PMT-H35: 96 to 153 cm Screen size 200"...
Page 9
PMT-H35 height adjustment The height adjustment pole for the PMT-H35 has holes spaced 3 cm apart that can be used to adjust the height. When the bracket is shipped from the factory, the pole is set at the shortest height.
INSTALLATION EXAMPLES When installing to a wooden ceiling Drill matching holes through the reinforcing plate and the ceiling in the proper locations and then pass bolts through the holes. Tighten the bolts to secure the reinforcing plate to a ceiling beam. Cautions •...
INSTALLING THE PROJECTOR Attach the projector mounting adapter onto the projector. Align the holes in the mounting adapter with the holes in the bottom of the projector, and then use the four projector mounting screws (M6, pan head) provided to securely attach the mounting adapter to the projector.
Page 12
Install the ceiling bracket on the ceiling. First hand-tighten the four nuts (eight nuts for PMT-H35) , determine the position, and then tighten the nuts securely. (PMT-L31) Caution • Use M8 bolts (commercially available) to install the ceiling bracket. Using any bolts other than M8 bolts could cause the projector to fall.
Page 13
Attach the safety brackets. Align the safety brackets so that the mounting guide pin fits into the hole, and then use the four safety bracket mounting screws (M4, pan head) to secure the brackets. (Use two screws on the left side and two screws on the right.) Temporarily secure the projector mounting adapter.
First, select a projection size using the zoom feature, and then adjust the angle. Adjust the horizontal angle. Adjust the projector so that the projected image is centered horizontally on the screen, and then tighten the horizontal angle adjustment screws (2 on the PMT-L31, 4 on the PMT-H35). Left Maximum angle of adjustment: ±10˚...
Page 15
Adjust the vertical angle. Adjust the projector so that the projected image is centered vertically on the screen, and then tighten the four vertical angle adjustment screws. (PMT-L31) Vertical angle adjustment screws (There are also screws located on the opposite side.) Adjust the tilt angle.