Functional Description; Installing Or Removing Battery Cartridge - Makita DLM460 Instruction Manual

ASSEMBLY
WARNING:
Always be sure that the lock key
and battery cartridge are removed before carrying
out any work on the mower. Failure to remove the
lock key and the battery cartridge may result in seri-
ous personal injury from accidental start-up.
WARNING:
Never start the mower unless it is
completely assembled. Operation of the machine
in a partially assembled state may result in serious
personal injury from accidental start-up.
Installing the handle
NOTICE:
When installing handles, position the
cords so that they are not caught by anything
between the handles. If the cord is damaged, the
mower switch may not work.
1. Attach the lower handle so that the holes in the
handle fit in the protrusions on the mower body. Insert
the bolts from inside, then attach washer A from outside,
and then tighten the thumb nuts.
► Fig.1: 1. Lower handle 2. Washer A 3. Thumb nut
4. Protrusion 5. Hole 6. Bolt
2. Align the hole in the lower handle with the hole
in the upper handle, then insert the bolts from inside,
then attach washer B from outside, and then tighten the
thumb nuts.
► Fig.2: 1. Upper handle 2. Hole 3. Washer B
4. Thumb nut 5. Lower handle 6. Bolt
CAUTION:
Hold the upper handle firmly so
that it does not drop off your hand. Otherwise, the
handle may fall and cause an injury.
3. Attach holder A and holder B to the handle.
Position the cords as shown in the figure.
► Fig.3: 1. Cord 2. Holder A 3. Holder B
NOTE: When attaching holder A, be sure to fix the
cord with the holder as shown in the figure.
Removing the mulching attachment
1.
Open the rear cover.
► Fig.4: 1. Rear cover
2. Remove the mulching attachment while holding
down the lever.
► Fig.5: 1. Lever 2. Mulching attachment
Assembling the grass basket
1. Pick up the upper clip of the grass basket.
► Fig.6: 1. Upper clip
2. Insert the frame into the grass basket as far as it
will go while holding the handle of the frame.
► Fig.7: 1. Handle
NOTICE:
Do not insert the handle into the grass
basket. Be sure to insert the frame along the stitch of
the grass basket.
3. Make sure that there is no sagging on the corners
of the grass basket.
► Fig.8
4.
Open the upper clip, and attach it to the frame.
► Fig.9
5. Attach all the other clips as shown in the figure. Make
sure that all the clips are securely attached to the frame.
► Fig.10: 1. Clip
► Fig.11
Installing the grass basket
1. Open the rear cover.
► Fig.12: 1. Rear cover
2. Hook the grass basket on the rod of the mower
body as shown in the figure.
► Fig.13: 1. Rod 2. Guard 3. Grass basket
NOTICE:
Make sure that the guard on the grass
basket is facing downward. Otherwise, the grass
basket may not catch all of cut-off grass.
Attaching the mulching attachment
1. Open the rear cover, and then remove the grass
basket.
► Fig.14: 1. Rear cover 2. Grass basket
2.
Attach the mulching attachment while holding
down the lever, and then release the lever to lock the
mulching attachment.
► Fig.15: 1. Lever 2. Mulching attachment
FUNCTIONAL
DESCRIPTION
Installing or removing battery
cartridge
CAUTION:
Always switch off the tool before
installing or removing of the battery cartridge.
CAUTION:
Hold the machine and the battery
cartridge firmly when installing or removing bat-
tery cartridge. Failure to hold the tool and the battery
cartridge firmly may cause them to slip off your hands
and result in damage to the tool and battery cartridge
and a personal injury.
CAUTION:
Make sure that you lock the battery
cover before use. Otherwise, mud, dirt, or water may
cause damage to the product or the battery cartridge.
CAUTION:
Always install the battery cartridge
fully until the red indicator cannot be seen. If not,
it may accidentally fall out of the tool, causing injury to
you or someone around you.
CAUTION:
Do not install the battery cartridge
forcibly. If the cartridge does not slide in easily, it is
not being inserted correctly.
13 ENGLISH