Table of Contents
Advertisement
Important safety instructions
1.
Read these instructions.
2.
Keep these instructions.
3.
Heed all warnings.
4.
Follow all instructions.
5.
Do not use this apparatus near water.
6.
Clean only with dry cloth.
7.
Do not block any ventilation openings. Install in
accordance with the manufacturer's instructions.
8.
Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including ampli ers) that produce heat.
9.
Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not t into your outlet, consult an electrician for
replacement of the obsolete outlet.
10.
Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
1 1.
Only use attachments / accessories speci ed by
the manufacturer.
12.
Use only with the cart, stand,
tripod, bracket, or table speci ed
by the manufacturer, or sold with
the apparatus. When a cart is
used, use caution when moving
the cart / apparatus combination
to avoid injury from tip-over.
Wall mount bracket kit
Brand
75 "
65 "
55 "
50 "
SANUS
43 "
40 "
32 "
24 "
Your TV meets the VESA standard for wall mounting. Consult
●
with your local dealer for a wall mount bracket which is com-
patible with your TV model.
The recommended wall mount bracket kit (sold separately)
●
allows the mounting of the TV on the wall.
For detailed information on installing the wall mount, refer to
●
the wall mount Instruction book.
Funai Corporation is not responsible for any damage to the prod-
●
uct or injury to yourself or others if you elect to install the TV wall
mount bracket or mount the TV onto the bracket on your own.
The wall mount bracket must be installed by experts.
●
Model #
Screw dimension
M8 x 0.787 " (20 mm)
M6 x 0.472 " (12 mm)
F80b
M6 x 1.378 " (35 mm)
SAN-25BB
M4 x 1.378 " (35 mm)
AST16
13.
Unplug this apparatus during lightning storms or
when unused for long periods of time.
14.
Refer all servicing to quali ed service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord
or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
Note to the CATV system installer:
This reminder is provided to call the CATV system
installer's attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in
particular, speci es that the cable ground shall be
connected to the grounding system of the building,
as close to the point of cable entry as practical.
Example of antenna grounding as per NEC -
National Electric Code
GROUND CLAMP
ELECTRIC SERVICE EQUIPMENT
Funai Corporation is not liable for these types of accidents or
injuries noted below.
Install the wall mount bracket on a sturdy vertical wall.
●
If installed onto a ceiling or slanted wall, the TV and wall mount
●
bracket may fall which could result in a severe injury.
Do not use screws that are longer or shorter than their speci-
●
ed length. If screws too long are used this may cause me-
chanical or electrical damage inside the TV set. If screws too
short are used this may cause the TV set to fall.
Do not fasten the screws by excessive force. This may damage
●
the product or cause the product to fall, leading to an injury.
For safety reasons use 2 people to mount the TV onto a wall
●
mounting bracket.
Do not mount the TV onto the wall mounting bracket while
●
your TV is plugged in or turned on. It may result in an electrical
shock injury.
When installing the unit on the wall, allow this much space.
Top
: 1 1.8 " (30 cm)
Left and right side
: 5.9 " (15 cm)
Bottom
: 3.9 " (10 cm)
ANTENNA LEAD IN WIRE
ANTENNA DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM (NEC ART 250,
PART H)
Advertisement
Table of Contents
