Download
Share
Print this page
Kenwood CA-CUT14 Instruction Manual
  1. Manuals
  2. Brands
  3. Kenwood Manuals
  4. Motorcycle Accessories
  5. CA-CUT14
  6. Instruction manual
Kenwood CA-CUT14 Instruction Manual

Kenwood CA-CUT14 Instruction Manual

Cut-in lid kit for 6” x 9” speakers designed and engineered for 2014-up harley-davidson rushmore motorcycles with factory-style hard saddlebags
Hide thumbs

Advertisement

Quick Links

Download this manual
Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain the best performance from your new product.
© 2023 JVCKENWOOD Corporation
CA-CUT14
CUT-IN LID KIT FOR 6" X 9" SPEAKERS DESIGNED AND ENGINEERED
FOR 2014-UP HARLEY-DAVIDSON® RUSHMORE MOTORCYCLES WITH
FACTORY-STYLE HARD SADDLEBAGS
INSTRUCTION MANUAL
JVCKENWOOD Corporation

Advertisement

loading

Related Manuals for Kenwood CA-CUT14

Summary of Contents for Kenwood CA-CUT14

  • Page 1 CA-CUT14 CUT-IN LID KIT FOR 6” X 9” SPEAKERS DESIGNED AND ENGINEERED FOR 2014-UP HARLEY-DAVIDSON® RUSHMORE MOTORCYCLES WITH FACTORY-STYLE HARD SADDLEBAGS INSTRUCTION MANUAL JVCKENWOOD Corporation Take the time to read through this instruction manual. Familiarity with installation and operation procedures will help you obtain the best performance from your new product.

  • Page 2: Table Of Contents

    WARNING The factory saddlebag hinges limit the size of the speaker magnet that can be used and allow the lids to open and close without issue. KENWOOD assumes ZERO RESPONSIBILITY for fitment issues, or water leaks when any speaker brand other than KENWOOD is used.

  • Page 3: Section 2: Disassembling The Factory Lid

    Section 1 - Getting Started - Cont. 3. Locate the wire harness and take the 48” section with the silicone grommet in line and install it into the saddle bag, making sure the 2 speaker “spades” are on the inside of the bag and the single 2-pin connector is on the outside of the bag.

  • Page 4: Section 3: Mounting The Templates

    Section 2 - Disassembling The Factory Lid - Cont. 2. Remove the 2 screws that hold the “key lock” to the factory lid. The chrome panel with the reflector built-in comes off the factory lid by removing the 3 screws right next to the key lock.
  • Page 5 Section 3 - Mounting The Templates - Cont. We Strongly suggest using a blade made SPECIFICALLY FOR PLASTICS. When cutting your lid with the correct blade, there should be ZERO smell of burning plastic! Incorrect blades will do more melting than cutting. CUTTING THE GRILLE OPENING STOP 4.
  • Page 6 Section 3 - Mounting The Templates - Cont. CLUTCH SIDE LID 6. Place the lid upside down on a blank et or something similar to protect its painted surface. Locate the speaker adaptor marked “Clutch”, noting that it only fits one way. In the order shown, put “thread forming” #4 ADD RUBBER screws through the adaptor and into the grille so the...

  • Page 7: Section 4: Wiring The Saddlebags For Speakers

    NOTE: The pre-terminated spade connectors on the harness inside the bag are correct for KENWOOD speakers but may need to have new terminals installed for other speakers. The larger connector (colored wire) is negative, and the smaller connector (black) is positive.
  • Page 8 Important Notes ©2023 JVCKENWOOD Corporation. All Rights Reserved. KENWOOD® and eXcelon® are registered trademarks of JVCKENWOOD Corporation. Harley-Davidson®, Electra Glide®, Road Glide®, Street Glide®, Ultra Classic®, Tri Glide®, CVO™, Screamin Eagle® and Tour-Pak® are trademarks or registered trademarks of Harley-Davidson, Inc. and/ or its affiliates and if used or implied are for reference only.