Sealey MS0812D Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
instructions
1. SAFETY
1.1. ELECTRICAL SAFETY FOR USE OF POWER SUPPLY
WARNING! DO NOT use any other type of power supply with this product. Only use the one provided. Failure to observe this warning
‰
could result in injury and or fire. The use of any other type of power supply will invalidate the warranty.
DO NOT turn on mains supply until the power supply lead is connected to the fan assembly.
8
WARNING! It is the user's responsibility to read, understand and comply with the following instructions.
‰
WARNING! You must ensure the risk of electric shock is minimised by the installation of appropriate safety devices e.g. RCD.
‰
NOTE: If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT
9
(Portable Appliance Test) tested.
Ensure that you inspect the power supply, cable and connections for wear and damage to ensure items are safe before connecting
9
them to the mains supply. If worn or damaged DO NOT use.
WARNING! There are no user serviceable components in the power supply. DO NOT dismantle.
‰
WARNING! For indoor use only. DO NOT allow the power supply to become wet. DO NOT use in wet or damp conditions.
‰
DO NOT pull the power supply plug from the mains socket by the lead.
8
DO NOT locate this product assembly in such a position as to create the risk of injury from contact with the head or any other
8
part of the body.
DO NOT overload this product; it should only be used for the designed purpose.
8
DO NOT locate in a position where items could fall from the product assembly owing to accidental contact.
8
Ensure that the product is firmly fixed to the wall refer to 4.4 below.
9
Ensure that, when installed, it can be accessed without over-reaching or over-balancing.
9
2. INTRODUCTION
A robust steel, powder paint coated, hanger. Can be mounted to your doors, walls or wardrobe. An integral, quiet running fan will
quickly and conveniently dry your helmet, whilst on the hanger. Inhibiting the build-up of damp and odour. Keep all your
motorbike gear in one place. This hanger comes with an integrated strap that will hold your gloves, and it can also be used to hang
your jacket, trousers or suit from. With the ability to mount the bracket where is convenient to you, this frees space from in your
wardrobe, hallway or cupboards, and can place your bike gear where you want it. The angle of the bracket can also best display the
decorative capabilities of a motorcycle helmet.
3. SPECIFICATION
Model No: ....................................................... MS0812D
Electrical Class: .......................................................... III
Plug Type: ..........................................3-Pin Transformer
4. INSTALLATION & ASSEMBLY
4.1. Attach the wall plate to the bracket using the four bolts provided. Ensure the wall plates are perpendicular to the bracket.
4.2. Hold the assembly in the desired position and mark the wall through the four holes, fig.1.
4.3. Remove from wall.
4.4. Use wall fixings that are suitable for the type of wall and the weight of the loaded product.
4.5. Drill four holes suitable for the wall fixings.
4.6. Fix the hook assembly to the wall.
5. OPERATION
5.1. FAN
5.1.1. Connect the power supply into the fan cooler plug connection.
5.1.2. Turn on power supply when required, in order to operate fan.
5.1.3.
© Jack Sealey Limited
HELMET HANGER/DRYER
MS0812D
MODEL NO:
Original Language Version
MS812D Issue 2 08/02/24