Download Print this page
Sealey LED20S Instructions
Sealey LED20S Instructions

Sealey LED20S Instructions

Extra slim solar floodlights with wall bracket

Advertisement

Quick Links

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
instructions
1. SAFETY
Maintain the light in good condition.
9
Ensure the light is installed correctly in accordance with these instructions.
9
Only install the light on a vertical surface.
9
DO NOT fix the light on any horizontal surface i.e. ceiling, or overhang.
8
Install away from flammable or combustible materials.
9
DO NOT direct the light into a persons eyes.
8
DO NOT install the light where it is likely to be knocked or hit.
8
DO NOT install in bathrooms, shower rooms, sauna or such locations.
8
DO NOT install near an exhaust outlet. e.g. Boiler flue, dryer outlet etc, or mirrored surfaces.
8
DO NOT put the light in an area that is well lit at night, e.g., near a street light. This may stop the sensor from determining when it
8
is night time and will stop the light from operating.
The light must be securely fixed to the mounting surface. The screws and wall plugs supplied are suitable for masonry only.
9
Mount the light level and horizontal to the ground.
9
Turn the light off if it is not to be used for long periods.
9
Locate the light away from obstructions that block the light from reaching the solar panel such as overhanging tree branches,
9
fences or buildings.
2. INTRODUCTION
Extra-Slim Solar floodlights with Wall Bracket. Features both daylight (CDS) and motion (PIR) sensors to switch on automatically.
Motion sensors can detect up to 6 metres. 30 second timer upon sensing motion. All year-round solar charging regardless of cloud
cover.
3. SPECIFICATION
Model No: ................................................... LED16S.V2
Battery: ........................................................... 3.7V 3Ah
IP Rating: ................................................................IP54
LED Type: .............................................................. SMD
Lumen Output: ................................................... 1600lm
Operating Time: .10 hours, once motion sensor activated
PIR Motion Sensor: .................................................. Yes
Power: .....................................................................16W
Modle No ..........................................................LED30S
Battery: ...................................................2 x 3.7V 2.6Ah
IP Rating: ................................................................IP54
LED Type: .............................................................. SMD
Lumen Output: ................................................... 3000lm
Operating Time: .10 hours, once motion sensor activated
PIR Motion Sensor: .................................................. Yes
Power: .....................................................................30W
4. ASSEMBLY
4.1.
Unpack the product and check contents. Should there be any damaged or missing parts contact your supplier immediately.
4.2.
Also includes fixing kit.
4.3.
Give careful consideration to the position of unit to ensure you obtain maximum benefit from the lighting range.
4.4.
With care remove the wall bracket from the light assembly by unscrewing the retaining thumb screws (fig 1).
4.5.
Locate the thumb screws, solar panel and light in a secure location.
4.6.
Place the wall bracket at your desired location and spot mark through the slots onto the fixing surface (fig 2).
4.7.
Secure wall bracket with appropriate fixings, wall plugs, to suit mounting surface.
4.8.
Reassemble the light assembly (fig 3).
WARNING! If working at height take adequate safety precautions to prevent injury from falling.
© Jack Sealey Limited
EXTRA SLIM SOLAR FLOODLIGHTS WITH
WALL BRACKET
LED16S.V2, LED20S, LED30S
MODEL NO:
Model No:.................................................................LED20S
Battery: ................................................................... 3.7V 3Ah
IP Rating: ........................................................................IP54
LED Type: ...................................................................... SMD
Lumen Output: ........................................................... 2000lm
Operating Time: ....... 10 Hours once motion sensor activated
PIR Motion Sensor: .......................................................... Yes
Power: .............................................................................20W
Original Language Version
LED16S, LED20S, LED30S
Issue 2 (3,5)
18/08/23

Advertisement

loading

Summary of Contents for Sealey LED20S

  • Page 1 LED16S.V2, LED20S, LED30S MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
  • Page 2 BATTERY REMOVAL Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme. Jack Sealey Ltd’s Batteries Producer Registration Number (BPRN) is BPRN00705.

This manual is also suitable for:

Led16s.v2Led30sLed16s