Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Beko BWD 6421
Summary of Contents for Beko BWD 6421
- Page 1 Built-In Automatic Washer Dryer Machine BWD 6421...
- Page 2 We advise you to read through this manual carefully before using your product and keep it for future reference. The User Manual will help you use your machine in a fast and safe way. • Read the User Manual before installing and starting your product.
-
Page 3: Table Of Contents
Wash/dry program status and power cuts ......17 Power Cuts ....17... -
Page 4: Your Washing Machine
Overview 6- Drain hose 7- Hatch 1- Power Cord 8- Adjustable feet 2- Control Panel 9- Water inlet hose 3- Detergent dispenser 4- Stainless steel drum 5- Accessible filter... -
Page 5: Warnings
(including children) could catch fire or explode. with reduced physical, sensory • Do not repair or replace any part of or mental capabilities, or lack of the washing machine or try to carry experience and knowledge, unless... -
Page 6: Installation And Assembly
• Remove the screws holding the plastic covers to the back of the washing machine. • Connect the bent end of the hose to the threaded inlet of the electrovalve located at the rear of the washing machine. • Loosen and remove the 3 blocking... -
Page 7: Drainage Connection
0.05 and 1MPa (0.05 and 10 Kgr/ hose must not be inserted in to the drain more than 15 cm. If it is too long, cut it shorter. • The end of the hose should not be... -
Page 8: Levelling
• If the length of the hose is too short, add an original extension hose. The maximum length of the hose must not be longer than 3.2 m from the machine outlet. To avoid water leak failures, the connection between the... -
Page 9: Pre-Cleaning
If the power cord is damaged, it must be replaced by a cord or special unit provided by either the manufacturer or your after sales service. With built-in washing machines, the plug must be accessible after installation. Pre-cleaning When your washing machine has been correctly installed, we recommend that you pre-clean the machine. -
Page 10: Preparing To Wash
Before using the drying programme, sizes within the same wash first check the label on the garment programme. This improves the to make sure it can be tumble dried. washing action and also aids the • Sort clothes according to how correct distribution of the garments soiled they are. -
Page 11: Detergent And Additives
The use of more detergent than necessary will not improve your washing results, and apart from costing you money it will have a negative effect on the preservation of the environment. We therefore recommend you follow the •... -
Page 12: Selection Of Washing And Drying Programme
Time delay button Drying time button Additional function button Detergent dispenser To select a wash programme, proceed If you select a wash + dry option, as follows: the load must not be over 4 • Starting from the off “0” position, kg. - Page 13 Anti-crease spin selection speed Spin Easy-iron wash Intensive rinse Extra programmes prog. programmes Normal Wool Delicate Auxiliary prog. Drying...
-
Page 14: Spin Speed Selection
LED will light up. Select Select Time delay selection Select Time delay selection button A delay of up to 24 hours can be selected. Select The delay must be selected after • No spin choosing the wash programme. -
Page 15: Additional Functions
Select Easy-iron Cancelling the delay This option prevents garments from To cancel the delay you have to press creasing by means of carrying out a the clock button successively. The special programme with special turns to delay will be cancelled when 24 hours... -
Page 16: Starting Up
Activating the lock function • The lock function is activated by pressing the Start/Stop button and holding it down for at least 3 seconds. The display will show if it is activated. -
Page 17: Wash/Dry Program Status And Power Cuts
Wash/dry program status and Power Cuts power cuts If there is a power cut, the washing machine will continue to operate from Programme Phases the point at which it stopped when Once started, current programme status power is reconnected (its memory lasts and time remaining till completion can for a few hours). -
Page 18: Maintenance And Cleaning
Pull outwards on the detergent dispenser to remove it completely. Maintenance After each wash, leave the door open for a while to allow the air to circulate • Use warm water and a brush to freely inside the machine. clean the compartments. -
Page 19: Cleaning The Filter
Cleaning The Filter Clean the accessible filter if the drain pump is blocked by any foreign objects. • Use a coin to turn the filter cap. • Pull out the filter cap. To avoid burns, do not carry out this operation when the wash water is at a temperature of over 30°C. -
Page 20: Safety And Troubleshooting
The washing machine has not been correctly levelled. Why doesn’t the washing machine take in water? • Indicator F01, no water coming in, this may be due to a cut in the water supply, a tap turned off or a blocked water inlet filter. •... - Page 21 This is due to the fact that the washing machine is provided with a system which is able to adapt to the load and type of fabrics, adjusting the levels of water and energy used, in order to preserve the environment.
-
Page 22: Guarantee
Guarantee • The guarantee will be void if the Your new product is guaranteed against the cost of breakdown repairs for twelve product is instalindicator light months from the date of the original or used in commercial or non- purchase. -
Page 23: Service
Service Please keep your purchase receipt or other Service once the manufacturers proof of purchase in a safe place; you will guarantee has expired. need to have it should the product require attention under guarantee. If you have purchased an extended... - Page 24 Beko plc. Beko House, Caxton Way, Watford Hertfordshire, WD18 8UF Tel: 0845 6004911 Fax: 0845 6004922 Email: service@beko.co.uk www.beko.co.uk...