A/V Receiver (Stereo System); Satellite Receiver Or Other Device With S-Video - Brother HL-2600CN Owner's Manual

Connecting an A/V Receiver (Stereo System)
Connecting a Satellite Receiver or Other Device with S -Video

A/V Receiver (Stereo System)

Figure 7
A digital audio cable and stereo audio cables are required.
These cables are not included with the TV.
To connect an analog A/V receiver:
1.
Connect a set of stereo audio cables from OUTPUT
AUDIO 2 on the TV back panel to the TV AUDIO
INPUT on the back of the A/V receiver. The red cable
connects to the R (right) channel and the white cable
connects to the L (left) channel.
2. To connect a digital A/V receiver with Dolby®
Digital surround sound:
Connect one end of the digital audio cable supplied
with the TV to DIGITAL AUDIO on the back of the
TV. Connect the other end to the COAXIAL DIGITAL
INPUT on the back of the A/V receiver.
Check the A/V receiver's Owner's Guide for information
concerning use of the digital input and switching between
digital sound and analog stereo sound from the TV.
COMPONENT
YPbPr (480i/480p/720p/1080i)
INPUT
1 2
1
2
Y
S-VIDEO
Pb
VIDEO Pr
AUDIO-
AUDIO-
LEFT/
LEFT/
(MONO)
(MONO)
AUDIO- AUDIO-
RIGHT RIGHT
MONITORLINK™/HDMI
VIDEO 480i/480p/720p/1080i
IR EMITTER
Net Command
DTV/CABLE/
VHF/UHF
DIGITAL
AUDIO
ANT 1 / MAIN ANT 2 / AUX OUTPUT CableCARD™ ANT 1 CARD TOP
USE WITH
Figure 7. Connecting an A/V receiver
Note: On rare occasions, an HDMI signal may be copy-
restricted and cannot be output from the TV as a digital
signal. To hear these copy-protected signals through the
A/V receiver, use connections for analog A/V receivers.
MP3 audio from memory cards cannot be connected
to digital audio. To listen to MP3 playback from the TV
MediaCommand memory card player through your A/V
receiver, use the connections for an analog A/V receiver.
28
Chapter 2. Connecting
INPUT OUTPUT
DVI AUDIO RECORD
Analog Audio OUTPUT
OUTPUT
1 2
VIDEO
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
PC - 60Hz
VGA, W-VGA,
AUDIO PCM LINEAR
SVGA, W-SVGA,
XGA, 1280 X 720
1 2
IEEE 1394
INPUT/
OUTPUT
Satellite Receiver or Other Device with
S-Video
Figure 8
An S-Video cable and audio cables are required. These are not
included with the TV.
1. Connect an S-Video cable from VIDEO OUT on the
satellite receiver back panel to INPUT-2 S-VIDEO on
the TV back panel.
2. Connect a set of audio cables from AUDIO OUT on
the satellite receiver back panel to INPUT-2 AUDIO
on the TV back panel. The red cable connects to
the R (right) channel and the white cable connects to
the L (left) channel.
Note: Refer to the Satellite Receiver Owner's
Guide for Dish Antenna connections
INPUT
1 2
S-VIDEO
VIDEO
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
IR EMITTER
Net Command
DTV/CABLE/
VHF/UHF
ANT 1 / MAIN
Figure 8. Connecting a Satellite Receiver with S-Video
Note: NetCommand® will assume you connected
your Satellite Receiver to Input-2. If you add a second
Satellite Receiver or use any other inputs for your
Satellite Receiver, this change must match in the
NetCommand system. See Editing NetCommand
Setup in Chapter 3 for more information.
COMPONENT
YPbPr (480i/480p/720p/1080i)
1 2
INPUT
OUTPUT
Y
DVI
AUDIO RECORD
Analog Audio OUTPUT
OUTPUT
Pb
1 2
Pr
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
MONITORLINK™/HDMI
PC - 60Hz
VIDEO 480i/480p/720p/1080i
VGA, W-VGA,
AUDIO PCM LINEAR
SVGA, W-SVGA,
XGA, 1280 X 720
1 2
DIGITAL
AUDIO
ANT 2 / AUX OUTPUT CableCARD™ USE WITH ANT 1 CARD TOP
VIDEO
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
IEEE 1394
INPUT/
OUTPUT