HP OmniBook 4100 Reference Manual
  1. Manuals
  2. Brands
  3. HP Manuals
  4. Laptop
  5. OmniBook 4100
  6. Reference manual
HP OmniBook 4100 Reference Manual

HP OmniBook 4100 Reference Manual

Hp omnibook 4100: reference guide
Hide thumbs Also See for OmniBook 4100:
Table of Contents

Advertisement

Quick Links

See also: Service Manual , User Manual
HP OmniBook 4100
Reference Guide

Advertisement

Table of Contents

Troubleshooting

loading

Related Manuals for HP OmniBook 4100

Summary of Contents for HP OmniBook 4100

  • Page 1 HP OmniBook 4100 Reference Guide...
  • Page 2 Notice This manual and any examples contained herein are provided “as is” and are subject to change without notice. Hewlett-Packard Company makes no warranty of any kind with regard to this manual, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose.
  • Page 3 If your computer was shipped with a product Recovery CD-ROM: (i) The product recovery CD-ROM and/or support utility software may only be used for restoring the hard disk of the HP computer with which the product recovery CD-ROM was originally provided. (ii) The use of any operating system...
  • Page 4 software by Microsoft contained in any such product recovery CD-ROM shall be governed by the Microsoft End User License Agreement (EULA). Customer may transfer rights in the software to a third party only as part of the transfer of all rights and only if Customer obtains the prior agreement of the third party to be bound by the terms of this License Agreement.

  • Page 5: Table Of Contents

    Contents 1. Introducing the OmniBook ....... Taking Inventory ........Included in the OmniBook 4100 box ....... To buy OmniBook accessories ......OmniBook features ........Setting Up Windows ........To set up the OmniBook ....... Configuring the OmniBook with the BIOS Setup Utility.....
  • Page 6 To delete a password........2-20 To install McAfee VirusScan ......2-20 To attach a security cable....... 2-21 To set PC identification ........ 2-22 To enable hard disk drive lock ......2-22 3. Managing Battery Power......... Monitoring Battery Power......... To check the battery status ......To respond to a low-battery warning .......
  • Page 7 5. Expanding the OmniBook ........ Installing a Hard Disk Drive ....... To replace the hard disk drive......To replace the hard disk drive holder ...... To create a Hibernate partition ......Installing a RAM Expansion Module ......To install a RAM expansion module ....... To remove a a RAM expansion module .....
  • Page 8 Startup Problems........7-15 Testing the Operation ........7-16 To create a diagnostic floppy disk ......7-16 To run the diagnostic test ....... 7-17 8. Specifications and Regulatory Information ....Hardware Specifications ......... Software System Resources........ Safety Information........Regulatory Information ........8-11 U.S.A.

  • Page 9: Introducing The Omnibook

    Introducing the OmniBook...
  • Page 10 Corporate Evaluator’s Guide The provides information about installing alternate operating systems, as well as how to configure the OmniBook in a corporate, networked environment. Located at the OmniBook website. HP Support Assist CD-ROM See the Support and Service booklet for telephone numbers.

  • Page 11: Taking Inventory

    Introducing the OmniBook Taking Inventory The HP OmniBook 4100 represents a new category of HP notebook computers featuring the latest mobile technologies available. It uses high-speed Intel Pentium and Pentium II processors with MMX technology, large TFT displays, and high-capacity hard drives.

  • Page 12: To Buy Omnibook Accessories

    Buy OmniBook accessories online! For the latest accessories and options, visit us at . As new accessories become available, you’ll find them listed here. At the time of this printing, HP offers a variety of docking solutions, plug-in modules, and other accessories, including the following: Docking system and monitor stand (HP F1477A).

  • Page 13: Omnibook Features

    Introducing the OmniBook OmniBook features OmniBook—Front View 1. Keyboard status lights (left to right: caps lock, keypad lock, num lock). 2. Built-in microphone. 3. Blue power button. Turns the OmniBook on and off. 4. Pointing stick (pointing device). 5. Touch pad (pointing device). 6.
  • Page 14 Introducing the OmniBook Taking Inventory 9. Mute button. 10. AC adapter jack. 11. Audio jacks (left to right): audio line-in, external microphone, audio line-out. 12. PC Card eject buttons (upper and lower PC Card slots). Press once to pop out the button, and press again to eject the card. 13.
  • Page 15 Introducing the OmniBook OmniBook—Back View 23. Infrared port. Windows NT 4.0 does not support infrared communication. Use this port for wireless data transmission between the OmniBook and another computer or a printer with an infrared port. You must install infrared drivers. 24.

  • Page 16: Setting Up Windows

    Introducing the OmniBook Setting Up Windows The OmniBook has either Windows 95 or Windows NT 4.0 factory-installed on the hard disk drive. When your OmniBook starts up the first time, it takes you through a series of setup screens, including installation of the operating system. This section describes how to set up the OmniBook with the factory-installed Windows operating system.

  • Page 17: To Set Up The Omnibook

    Introducing the OmniBook To set up the OmniBook 1. Remove the “weight-saving” module. Slide the release latch forward, then push it back as far as it will go. You can use the weight-saving module in place of your CD-ROM or floppy disk drive to lighten the OmniBook.
  • Page 18 Introducing the OmniBook 3. Plug in the ac adapter, then connect the ac adapter to the OmniBook’s right side, as shown. The OmniBook battery starts charging. 4. Press the blue power button. The Windows 95 or Windows NT Setup program starts automatically.

  • Page 19: Configuring The Omnibook With The Bios Setup Utility

    1. Close all applications, then shut down Windows and restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. The pointing devices are not active in the BIOS Setup utility. Press the RIGHT and LEFT arrow keys to move among menus.
  • Page 20 Introducing the OmniBook Main Menu Default Language Sets the language for this utility and for BIOS Same as messages. operating system. BIOS Revision Shows the current BIOS version. Detected automatically. System Time Sets the time using 24-hour format. Values set take effect immediately. System Date Sets the date using dd/mm/yy format (except English, which is mm/dd/yy format).
  • Page 21 Introducing the OmniBook System Devices Menu Default Internal Pointing Devices Enables one or both built-in PS/2 devices. Both External Fn Key Sets whether left-CTRL + left-ALT on an Enabled external keyboard is interpreted as the Fn key. IDE Controller Enables the primary (hard drive) and secondary Both (optional CD-ROM drive) controllers.

  • Page 22: Security Menu

    Introducing the OmniBook 1st DMA channel Sets the DMA channel for playback. DMA1 2nd DMA channel Sets the DMA channel for recording. DMA0 Security Menu Default User Password Is Shows if a user password is set. Clear Administrator Password Is Shows if an administrator password is set.

  • Page 23: Power Menu

    Introducing the OmniBook Power Menu Default Power Management Mode Disables time-outs, selects a combination of Max Power time-outs, or allows customized time-outs. Savings Smart CPU Mode Enables automatic CPU power savings. Absence of keyboard, mouse, and hard disk activity could cause slower CPU response.

  • Page 24: Exit Menu

    Introducing the OmniBook Boot Menu Default Diskette Drive Shows the order of boot devices. Move the 1. Diskette drive Hard Drive entries to change the order. 2. Hard drive CD-ROM Drive 3. CD-ROM drive Exit Menu Save Changes and Exit Saves Setup changes, exits, and reboots.

  • Page 25: Configuring The Omnibook With Toptools

    TopTools may be run locally on a PC or remotely by a network administrator. To run TopTools locally, click Start, Programs, HP DMI, HP TopTools. To get more information about TopTools For information on manageable HP PCs, HP TopTools, DMI, and how they lower PC operating costs, see the HP website at 1-17...

  • Page 27: Operating The Omnibook

    Operating the OmniBook...

  • Page 28: Operating The Omnibook

    Operating the OmniBook This chapter introduces the OmniBook and helps you get familiar with basic operation, including Starting and stopping the OmniBook. Using the OmniBook pointing devices. Managing pointing devices. Using the OmniBook display. Adjusting the audio system. Using the OmniBook keyboard. Checking the status of the OmniBook.

  • Page 29: Starting And Stopping The Omnibook

    Operating the OmniBook Starting and Stopping the OmniBook You can easily start and stop your OmniBook using the blue power button. However, at certain times, you may want to use other methods for starting and stopping your OmniBook—depending on power considerations, types of active connections, and start-up time.

  • Page 30: To Reset The Omnibook

    Operating the OmniBook To reset the OmniBook If Windows or the OmniBook stops responding, you can reset the OmniBook and restart Windows. If possible, shut down Windows. Insert a pen or straightened paper clip into the recess on the right side of the OmniBook, as shown.

  • Page 31: Using The Omnibook Pointing Devices

    Operating the OmniBook Using the OmniBook Pointing Devices Two pointing devices (pointing stick and touch pad) are built into your OmniBook. The default pointing device driver (PS/2 TrackPoint), supports the enhanced features of the pointing stick and basic features the touch pad. You can customize the OmniBook to support enhanced touch pad features.

  • Page 32: To Use The Built-In Pointing Devices

    Operating the OmniBook To use the built-in pointing devices 1. Place your hands in the typing position. With your index finger, press the pointing stick in the direction you want the pointer to move. Pressing away from you moves the pointer up the screen;...

  • Page 33: To Activate Full Touch Pad Capabilities

    Disable the pointing stick 1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. Select the System Devices menu. 4. Highlight Internal Pointing Devices and select Touch Pad.

  • Page 34: To Activate Full Pointing Stick Capabilities

    Enable the pointing stick 1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. Select the System Devices menu. 4. Highlight Internal Pointing Devices and select Pointing Stick. (Choose Both if you want basic touch pad features available.)

  • Page 35: To Configure Pointing Devices

    Operating the OmniBook To configure pointing devices To customize the operation of all pointing devices (pointing stick, touch pad, and external PS/2 or serial mouse), in Control Panel open Mouse. You can change left and right button actions, double-click speed, pointer speed and tail, and more.

  • Page 36: Using The Omnibook Display

    Operating the OmniBook Using the OmniBook Display This section describes How to adjust the display brightness. How to extend the life of the display. To adjust the display brightness The OmniBook uses special key combinations, called hot keys, to control brightness. Press Fn+F1 to decrease the brightness.

  • Page 37: Adjusting The Audio System

    Operating the OmniBook Adjusting the Audio System The OmniBook supports Sound Blaster Pro-compatible sound and the Microsoft Windows Sound System. This section describes How to adjust the volume manually. How to adjust the volume in Windows. To adjust the volume manually To increase the volume, press Fn+UP-ARROW.

  • Page 38: Using The Omnibook Keyboard

    Operating the OmniBook Using the OmniBook Keyboard This section describes the OmniBook’s keyboard features, including how to Use the Fn hot keys. Use the Windows keys. Use the embedded keypad. Use the ALT GR key on a non-US keyboard. 2-12...

  • Page 39: To Use The Fn Hot Keys

    Operating the OmniBook To use the Fn hot keys The combination of the Fn key plus another key creates a hot key—a shortcut key sequence—for various system controls. The OmniBook keyboard shows the Fn hot keys labeled in gray. Fn + F1 Decreases the display’s brightness.

  • Page 40: To Use The Windows Keys

    Operating the OmniBook To use the Windows keys There are two Windows keys on the keyboard. The one next to the Fn key brings up the Windows Start menu. The one at the top center of the keyboard brings up the shortcut menu for the current application.

  • Page 41: To Use The Alt Gr Key

    Operating the OmniBook To use the ALT GR key Non-U.S. keyboards have an ALT GR key to the right of the spacebar. This is a shift key providing access to certain keyboard characters. For a character in the lower-right corner of a key, press and hold ALT GR to type the character.

  • Page 42: Checking The Status Of The Omnibook

    Operating the OmniBook Checking the Status of the OmniBook This section describes how to interpret the status lights. To interpret the status lights The OmniBook has status lights that report power status and drive activity. When the floppy disk drive is installed in the module bay, the following lights are present on the front of the OmniBook.
  • Page 43 Operating the OmniBook Keyboard Status Lights The keyboard status lights, located above the keyboard, indicate the states of the keyboard locks. 1. Caps Lock. Caps Lock is active. 2. Keypad Lock. The embedded keypad is active (Fn+F8). Num Lock must also be on for the numeric keys—otherwise, cursor control is active.

  • Page 44: Protecting The Omnibook

    Operating the OmniBook Protecting the OmniBook Your OmniBook provides several ways for you to identify and protect your computer. This section describes how to Set or change a password. Delete a password. Attach a security cable. Install McAfee VirusScan. Set unique PC identification. Enable drive lock protection.

  • Page 45: To Set Or Change A Password

    1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. Select the Security menu. 4. Select Set Administrator Password, then press ENTER.

  • Page 46: To Delete A Password

    1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. Select the Security menu. 4. Select Set Administrator Password, then press ENTER.

  • Page 47: To Attach A Security Cable

    Operating the OmniBook To attach a security cable Your OmniBook has a built-in connector that allows you to secure the OmniBook with a cable. The Kensington MicroSaver lock system works with this connector and is available at many computer stores. 1.

  • Page 48: To Set Pc Identification

    Hard disk drive lock helps you keep your information secure. 1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. From the Security menu, enable Password Required To Boot.

  • Page 49: Managing Battery Power

    Managing Battery Power...

  • Page 50: Managing Battery Power

    Managing Battery Power The OmniBook conserves power by using Advanced Power Management (APM), software that controls battery charging and power drain. , APM is preinstalled on the OmniBook. , you’ll need to install APM (see page 6-17 for instructions). The OmniBook provides several safeguards so you won’t be surprised by a dead-battery condition, including the following: Built-in warnings are displayed for low-battery conditions.

  • Page 51: Monitoring Battery Power

    Managing Battery Power Monitoring Battery Power The primary source of power for the OmniBook is its rechargeable battery pack. You can use the ac adapter to recharge the battery—or to run on ac power to preserve the battery. You can also install a second battery in the plug-in module bay for increased battery time.

  • Page 52: To Check The Battery Status

    Managing Battery Power To check the battery status From the Windows Taskbar Move the pointer onto the power icon at the right end of the taskbar. If you are using Windows NT 4.0, you’ll need to install Advanced Power Management to display the power icon (see page 6-17).

  • Page 53: To Recharge A Battery

    Managing Battery Power To recharge a battery 1. Connect the power cord to the ac adapter, then plug the cord into an ac outlet. The indicator light on the ac adapter shines when the adapter is on. If the ac adapter does not light, make sure that cord is not damaged.

  • Page 54: To Replace The Main Battery

    Managing Battery Power Optimum Charging To get the longest battery operating time, continue charging until the OmniBook battery is fully charged. The battery charging light stops blinking only when the battery is actually full. You can continue working while the battery is charging. To replace the main battery If you have any unsaved data, it (and your current work session) will be lost when you remove the battery unless the computer is connected to ac power or a second...
  • Page 55 Managing Battery Power 5. Grasp the underside of the battery firmly and pull out. 6. With the latch in the open position, slide the charged battery into the OmniBook until it is flush with the unit. 7. Close the battery bay release latch. The battery module fits into either the module bay or the battery bay.

  • Page 56: To Install A Second Battery

    Managing Battery Power To install a second battery The OmniBook’s plug-in module bay accepts a second battery. See page 4-4 for more information about plug-in modules. 1. Click the Start button and select Shut Down (this is not necessary if you are removing a battery from the plug-in module bay and inserting another battery).

  • Page 57: Conserving Battery Power

    Managing Battery Power Conserving Battery Power The OmniBook uses Advanced Power Management (APM) to conserve battery power. You can take steps to optimize your battery operating time. This section describes how to Save battery power. Set time-outs. Handle and store the battery safely. Get the most from your battery.

  • Page 58: To Set Time-Outs

    1. From the Start menu, shut down then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. Active keys are described along the bottom of the screen. (The touch pad does not work in Setup.) Help information for the highlighted item appears in the right-hand...

  • Page 59: To Get The Most From Your Battery

    Managing Battery Power To get the most from your battery The following are some further suggestions for the best management of your OmniBook batteries. Do not leave batteries unused for long periods of time. If you have more than one, rotate them. If you normally use ac power, make a practice of at least once a week using the battery as your power source.

  • Page 61: Making Connections

    Making Connections...
  • Page 62 Making Connections This chapter describes procedures to expand the capabilities of your OmniBook, including Using OmniBook plug-in modules. Connecting external devices. Using PC Cards. Using docking products.

  • Page 63: Using Omnibook Plug-In Modules

    The floppy drive module can also be connected externally via the parallel port. If you want to do this, you’ll need to order the external floppy cable (HP F1473A). You can order this online at http://www.hp.com/omnibook. This connector cannot be...

  • Page 64: To Replace A Plug-In Module

    Making Connections To replace a plug-in module If you are inserting or removing a CD-ROM drive, floppy disk drive, LS-120 drive, or DVD drive, shut down the OmniBook. 1. From the Start menu, shut down the OmniBook. (This is not necessary if you are removing a battery from the plug-in module bay and inserting another battery.) 2.

  • Page 65: To Insert Or Eject A Floppy Disk

    Making Connections To insert or eject a floppy disk 1. Hold the disk with its face up, then slide it into the floppy disk drive slot until it clicks into place. 2. To remove the floppy disk, press the eject button on the front of the drive.

  • Page 66: To Insert Or Remove A Cd

    Making Connections To insert or remove a CD 1. Press the button on the face of the CD-ROM drive. If you are using this drive for the first time, be sure to remove the cardboard packing insert. 2. Place the CD into the drive (label facing up) and gently press down to seat the CD on the spindle–or–remove the CD.

  • Page 67: Connecting External Devices

    Making Connections Connecting External Devices You can expand the OmniBook’s capabilities by connecting other devices. Before you connect any device, check the documentation that came with the equipment to see if you need to make any settings or adjustments to the equipment before using it.

  • Page 68: To Identify Connectors For External Devices

    Making Connections To identify connectors for external devices The following graphic describes the available connectors for external devices. Refer to it, if necessary, when following the procedures in this section. 1. Infrared port. Windows NT 4.0 does not support infrared communication. Use this port for wireless data transmission between the OmniBook and another computer or a printer with an infrared port.

  • Page 69: To Connect An External Monitor

    1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. From the Main menu, use the down arrow to highlight Video Display Device.

  • Page 70: To Connect A Parallel Device

    Making Connections To connect a parallel device The parallel port uses a standard 25-pin connector, most commonly used for connecting a printers. These include dot-matrix, ink-jet, and laser printers. The parallel port supports both EPP and ECP capabilities (if selected in BIOS Setup). The OmniBook has one parallel port.

  • Page 71: To Connect An External Keyboard Or Ps/2 Mouse

    USB devices—this is called a “daisy-chain” connection. If you have problems making this connection, contact the vendor of the peripheral device, as well as the HP website, for the latest versions of the USB drivers. The USB technology is dynamic and continues to develop.

  • Page 72: To Connect Audio Devices

    Making Connections To connect audio devices There is a built-in microphone located just below the OmniBook display. You can use it to record voice, sound, and music. You can also plug in a stereo input source, (such as a CD player), an external microphone, external speakers or headphones. Attach the audio cable to the corresponding audio port.

  • Page 73: To Make An Infrared Connection

    Making Connections To make an infrared connection Windows NT 4.0 does not support infrared communication. By default, the infrared port is not enabled. You must enable it in the BIOS Setup utility and then install the appropriate infrared driver. For details, refer to the driver’s Readme file located in \OmniBook\drivers\Win95.

  • Page 74: Using Pc Cards

    Making Connections Using PC Cards This section describes how to Insert and remove a PC Card. Select a compatible PC Card from a list of tested cards. To insert and remove a PC Card Windows NT 4.0 does not support zoomed video. If you are using Windows NT 4.0, make sure you’ve installed Card Executive (see page 6-18 for instructions).

  • Page 75: List Of Tested Pc Cards

    At the time of this printing, the following cards have been tested for use with the OmniBook. For the latest information about compatible cards, visit our website at http://www.hp.com/omnibook and check the Accessories section. Or contact Hewlett-Packard as described in the Support and Service booklet. 3COM...

  • Page 76: Using Docking Products

    Your dock requires a tray that accommodates your specific OmniBook model. Install this tray prior to connecting the OmniBook to the dock. 1. Select the tray labeled for the OmniBook 4100. 2. Slide the rear of the tray into the dock as shown on the dock label.

  • Page 77: To Dock The Omnibook

    Making Connections To dock the OmniBook 1. If you’re using Windows NT, click Start, Shut Down. 2. Plug the power cord into the ac adapter, then into an ac outlet. Plug the ac adapter into the dock. Do not plug in the OmniBook’s ac adapter while using the dock.
  • Page 78 Making Connections 4. Position your fingers on the platform grips as shown below. Use your thumbs to push the computer into the dock until the computer slides into place. 4-18...

  • Page 79: To Undock The Omnibook

    Making Connections To undock the OmniBook 1. If you’re using Windows NT, click Start, Shut Down. 2. Press the undock button on the front of the dock and wait for the undock light to turn green. Then position your thumb as shown and pull the release lever forward.

  • Page 81: Expanding The Omnibook

    Expanding the OmniBook...

  • Page 82: Expanding The Omnibook

    Expanding the OmniBook This chapter describes some of the optional equipment that can be added to the OmniBook—components installed inside the computer rather than connected to the computer’s I/O ports. This chapter describes procedures to expand or update the capabilities of your OmniBook, including Installing a hard disk drive.

  • Page 83: Installing A Hard Disk Drive

    Expanding the OmniBook Installing a Hard Disk Drive This section describes how to Replace the hard disk drive. Replace the hard disk drive holder. Create a hibernate partition for a new hard disk drive. To replace the hard disk drive You’ll need a small Phillips screwdriver for this procedure.

  • Page 84: To Replace The Hard Disk Drive Holder

    Expanding the OmniBook To replace the hard disk drive holder If you are installing a new hard drive that does not have a cover, you can remove the cover parts from the old hard drive. You’ll need a small flat blade screwdriver for this procedure.
  • Page 85 Expanding the OmniBook 3. Pry out the corner next to the connector, then lift out the connector and hard drive together. 4. Unplug the internal connector and cable from the hard drive.

  • Page 86: To Create A Hibernate Partition

    Expanding the OmniBook To create a Hibernate partition You’ll need the OmniBook, its CD-ROM drive, and the OmniBook Recovery CD to create a hibernate partition. 1. Connect the ac adapter to the OmniBook. 2. Insert the CD-ROM drive in the OmniBook. 3.

  • Page 87: Installing A Ram Expansion Module

    Expanding the OmniBook Installing a RAM Expansion Module The OmniBook provides an optional memory expansion slot for installing a 3.3-volt EDO RAM expansion module. This section describes how to Install a RAM expansion module. Remove a RAM expansion module.

  • Page 88: To Install A Ram Expansion Module

    Expanding the OmniBook To install a RAM expansion module Your OmniBook’s computer chips are extremely static-sensitive. Static electricity can permanently damage computer chips. Before starting, reading the caution on page 5-7 about how to handle RAM expansion modules. 1. From the Start menu, shut down the OmniBook. 2.

  • Page 89: To Remove A A Ram Expansion Module

    Expanding the OmniBook To remove a a RAM expansion module Your OmniBook’s computer chips are extremely static-sensitive. Static electricity can permanently damage computer chips. Before starting, reading the caution on page 5-7 about how to handle RAM expansion modules. 1. From the Start menu, shut down the OmniBook. 2.

  • Page 91: Using The Recovery Cd

    Using the Recovery CD...
  • Page 92 Using the Recovery CD You can use the OmniBook Recovery CD to recover an original OmniBook build, or you can use it to install the HP custom software over a user-installed alternate operating system. The Recovery CD provides the OmniBook-specific drivers to configure your custom system.

  • Page 93: Recovering A Factory Build

    Using the Recovery CD Recovering a factory build If you’ve deleted or lost files on the OmniBook, causing the system to work improperly, you may need to recover the original factory build. This section describes how to Recover the OmniBook factory installation of Windows 95. Recover the OmniBook factory installation of Windows NT 4.0.

  • Page 94: To Recover The Windows 95 Factory Installation

    2. Connect the ac adapter and turn on the OmniBook. 3. When you see the HP logo, press F2 to enter the BIOS Setup utility. 4. Open the Boot menu and select CD-ROM as the first boot device. (You may want to change the boot order back to Diskette Drive after completing this procedure.)

  • Page 95: To Recover The Windows Nt Factory Installation

    2. Connect the ac adapter and turn on the OmniBook. 3. When you see the HP logo, press F2 to enter the BIOS Setup utility. 4. Open the Boot menu and select CD-ROM as the first boot device. (You may want to change the boot order back to Diskette Drive after completing this procedure.)

  • Page 96: Installing Retail Windows 95

    2. Insert the CD-ROM drive in the module bay. 3. Connect the ac adapter and turn on the OmniBook. 4. When you see the HP logo, press F2 to enter the BIOS Setup utility. 5. Insert the Recovery CD into the CD-ROM drive.
  • Page 97 25. Do not detect any Network, Sound, MIDI, or Video Capture Card devices, then click Next. 26. Follow the prompts until the end of the installation, and then reboot. 27. Copy the files in D:\Omnibook from the OmniBook 4100 Recovery CD to C:\Omnibook.

  • Page 98: To Install Video Support For Retail Windows 95

    Using the Recovery CD To install video support for retail Windows 95 If you’ve installed a retail version of Windows 95, you’ll need to install video support. The driver is located on the OmniBook’s hard drive or on the Recovery CD in the \Omnibook\Drivers\Win95\Video directory.

  • Page 99: To Install Audio Support For Retail Windows 95

    Using the Recovery CD To install audio support for retail Windows 95 If you’ve installed a retail version of Windows 95, you’ll need to install audio support. This driver is located on the OmniBook’s hard drive or on the Recovery CD in \Omnibook\Drivers\Win95\Audio.

  • Page 100: To Install Pc Card Support For Retail Windows 95

    2. If prompted to overwrite old files, click Yes. 3. Reboot the OmniBook. 4. When you see the HP logo, press F2 to enter the BIOS Setup utility. 5. Go to the System Devices menu. 6. Set the Infrared Port to Enabled.
  • Page 101 Using the Recovery CD 11. Save and exit the BIOS Setup utility. 12. When prompted for a driver disk, select the driver disk provided by the hardware manufacturer, then click OK. 13. Enter the directory of the infrared drivers (\Omnibook\Drivers\Win95\Fastir) and click OK.

  • Page 102: Installing Retail Windows Nt 4.0

    Using the Recovery CD Installing Retail Windows NT 4.0 If you install a retail version of Windows NT 4.0 you’ll also need to manually install video, audio, Advanced Power Management (APM), and Card Executive drivers. This section describes how to Install a retail version of Windows NT 4.0.

  • Page 103: To Install A Retail Version Of Windows Nt 4.0

    2. Connect the ac adapter and turn on the OmniBook. 3. When you see the HP logo, press F2 to enter the BIOS Setup utility. 4. From the Boot menu, select CD-ROM as the first boot device. (You may want to change the boot order back to Diskette Drive after completing this procedure.)

  • Page 104: To Install Service Pack 3 For Retail Windows Nt 4.0

    Using the Recovery CD When choosing a file system, refer to the Windows NT Resource Kit for a detailed discussion of FAT and NTFS file systems. 13. When prompted, choose No, Do Not Create An Emergency Repair Disk, then click Next. If is more useful to create a repair disk after installation is complete and after you have installed your drivers and other applications.

  • Page 105: To Install Video Support For Retail Windows Nt 4.0

    Using the Recovery CD To install video support for retail Windows NT 4.0 If you’ve installed a retail version of Windows NT 4.0, you’ll need to install video support. The driver is located on the Recovery CD in \Omnibook\Drivers\Nt40\Video. 1. Insert the Recovery CD into the CD-ROM drive. 2.

  • Page 106: To Install Audio Support For Retail Windows Nt 4.0

    Using the Recovery CD To install audio support for retail Windows NT 4.0 If you’ve installed a retail version of Windows NT 4.0, you’ll need to install audio support. The driver is located on the Recovery CD in \Omnibook\Drivers\Nt40\Audio. 1. Insert the Recovery CD into the CD-ROM drive. 2.

  • Page 107: To Install Apm For Retail Windows Nt 4.0

    Using the Recovery CD To install APM for retail Windows NT 4.0 You need to install Advanced Power Management for Windows NT 4.0 for both the retail and factory-installation. The driver is located on the Recovery CD in \Omnibook\Drivers\Nt40\Apm. Phoenix APM 2.0 adds the following capabilities to the OmniBook: Improved battery life under Windows NT 4.0.

  • Page 108: To Install Card Executive 2.X For Retail Windows Nt 4.0

    Using the Recovery CD To install Card Executive 2.x for retail Windows NT 4.0 To take advantage of Card Executive’s plug-n-play for PCMCIA network cards, you must install Card Executive before installing Windows NT networking. The driver is located on the Recovery CD in \Omnibook\Drivers\Nt40\Pccard. Card Executive adds the following capabilities to your OmniBook: Plug and Play for PC Cards using standard Windows NT drivers.

  • Page 109: Recovering Omnibook Files

    If you lose or damage the Recovery CD, take your OmniBook and Certificate of Authenticity to an HP Service Center to be replaced. If you mail your OmniBook for this service, you must provide a photocopy of the Certificate of Authenticity along with payment.

  • Page 110: To Update The Omnibook Bios

    To update the OmniBook BIOS Hewlett-Packard may update the BIOS to enhance the capabilities of the OmniBook. Updates will be available from HP Electronic Support Services. From the Start menu, shut down the OmniBook. Connect the ac adapter to the OmniBook.

  • Page 111: Troubleshooting

    Troubleshooting...

  • Page 112: Troubleshooting

    Look at the online Help for Windows and other applications. Find technical information about the OmniBook on the Internet—visit the Support website at http://www.hp.com/omnibook. See other books about Windows, MS-DOS, and other applications. Check your local library or bookstore.

  • Page 113: Solving Problems

    If you always want to boot from a CD, check boot order in BIOS Setup. 1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. Open the Boot menu. The default boot order is...

  • Page 114: Audio Problems

    Check settings in BIOS Setup. 1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. From the System Devices menu, check that Audio is enabled.

  • Page 115: Display Problems

    Troubleshooting Display Problems If the OmniBook is on, but the screen is blank Press the space bar to see if the computer is in Standby mode. Press Fn+F1 or Fn+F2 to adjust the display. If you are using an external keyboard, Fn = CTRL+ALT.

  • Page 116: Hard Disk Drive Problems

    Troubleshooting Hard Disk Drive Problems If the OmniBook’s hard drive doesn’t spin Check the power source. Remove and reinsert the hard drive. See page 5-3 for instructions. If the hard disk makes buzzing or whining noise Back up the drive immediately. Check for alternate noise sources, such as the fan or a PC Card drive.

  • Page 117: Keyboard And Pointing Device Problems

    Make sure the touch pad or pointing stick is enabled in the BIOS Setup utility. 1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. From the System Devices menu, check Internal Pointing Devices.

  • Page 118: Infrared Problems

    Check settings in BIOS Setup utility. 1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. From the System Devices menu, check that Infrared Port is enabled.

  • Page 119: Memory Problems

    Help search for MS-DOS troubleshooter. Not all 3rd party memory cards have been tested with the OmniBook. Please check the HP website for a list of approved and tested PC Cards. PC Card (PCMCIA) Problems If the OmniBook doesn’t recognize a PC Card Make sure Card Executive is installed for Windows NT.

  • Page 120: Performance Problems

    Check the BIOS Setup settings. 1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. From the Power menu, set the Power Management Mode to Max.

  • Page 121: Power And Battery Problems

    1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. From the Power menu, make sure the Power Management Mode is set to Maximum Power Savings.
  • Page 122 Troubleshooting If the battery doesn’t charge Make sure the ac adapter is plugged into the power source. Check that the light on the ac adapter is on. Check that the battery is fully installed and locked in place. Turn off the OmniBook, then check that the battery contacts are clean and that the ac adapter cables are fully plugged in.

  • Page 123: Printing Problems

    If the printer you are using is a 600-dpi (dots per inch) printer, try selecting a compatible printer driver for a 300-dpi printer. For example, for a 600-dpi HP LaserJet printer, try using the HP LaserJet IIIsi driver (300-dpi). Certain applications may not work properly with 600-dpi printers.

  • Page 124: Serial, Parallel, And Usb Problems

    Check settings in BIOS Setup. 1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. From the System Devices menu, check that Parallel and Serial are enabled.

  • Page 125: Startup Problems

    Check boot order in BIOS Setup utility. 1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. Open the Boot menu. The default boot order is...

  • Page 126: Testing The Operation

    \Dmi\Hpdiags directory on the hard disk. –or– If HP TopTools is installed, use the DiagTools page to create the disk. On any computer with a CD-ROM drive, run from the \Omnibook\Dmi\Hpdiags directory on the OmniBook 4100 Recovery CD.

  • Page 127: To Run The Diagnostic Test

    Troubleshooting To run the diagnostic test 1. Insert the diagnostic disk in the floppy drive. 2. Reboot the OmniBook. 3. Go through the first several screens. 4. When the hardware detection finishes, check the list of detected hardware. If a device is not detected or fails its test below, it may be configured incorrectly in the BIOS Setup utility.

  • Page 129: Specifications And Regulatory Information

    Specifications and Regulatory Information...

  • Page 130: Specifications And Regulatory Information

    Specifications and Regulatory Information Your OmniBook is designed to provide trouble-free operation. The following suggestions can help you maintain its dependability: Observe the temperature limits and other specifications listed in the next section. If you have problems, see the problem-solving suggestions in chapter 8 of this manual.

  • Page 131: Hardware Specifications

    Specifications and Regulatory Information Hardware Specifications Size: 330.5mm×256.9mm×35-36.5mm (13.0"×10.1"×1.3-1.4"). Weight: 2.92 kg (6.45 lb). 233/266-MHz Intel Pentium II processor with MMX technology. –or– 266-MHz Intel Pentium processor with MMX technology. 1.6-V core, 2.5-V external, low-power processor. 32-KB (16-KB instruction, 16-KB data) L1 cache. 512-KB pipeline-burst-synchronous L2 cache.
  • Page 132 Microsoft Windows 95 or Windows NT 4.0. Windows 95-compatible Plug-and-Play. Windows NT 4.0 APM and PC Card Plug-and-Play. Advanced Power Management (APM 1.2). DMI 2.0 with HP TopTools 2.6. McAfee Virus Scan 3.14. Online documentation. OmniBook Recovery CD included. Centralized worldwide BIOS and driver update service.
  • Page 133 Specifications and Regulatory Information CPU: Intel Mobile Pentium or Pentium II. South Bridge: PIIX4E. Video: NeoMagic MagicGraph NM2160. Audio: Crystal CS4237B. CardBus: TI PCI1250A. Keyboard controller: National PC87570. Super I/O: SMC 769. F1474A 24x CD-ROM drive module. F1472A Floppy drive module. F1473A Floppy drive cable for external use.

  • Page 134: Software System Resources

    Specifications and Regulatory Information Software System Resources Below are default values for the system resources. To see other, non-default possibilities, refer to the BIOS Setup utility, which lists port and audio device configurations in the Input/Output menu. The tables in this section show typical resource usage as set up by the OmniBook BIOS.
  • Page 135 Specifications and Regulatory Information 170-177 Internal CD-ROM drive (secondary IDE controller) 1F0-1F7 Internal hard disk (primary IDE controller) 220-22F Crystal sound Internal CD-ROM drive (secondary IDE controller) 378-37F LPT1 (printer port) 388-38B Sound 3B0-3BB VGA adapter 3C0-3DF VGA adapter 3E0-3E1 PCMCIA controller 3F0-3F5 Floppy controller...

  • Page 136: Safety Information

    To purchase a power cord (including one for a country not listed below) or a replacement ac adapter (HP part number F1454A), contact your local Hewlett-Packard dealer or Sales and Service office.
  • Page 137 When discarding a battery pack, contact your local waste disposal provider regarding local restrictions on the disposal or recycling of batteries. To obtain a replacement battery, contact your local dealer or HP sales office. Do not charge the battery pack if the ambient temperature exceeds 45 °C...
  • Page 138 EN60825-1). This device is not considered harmful, but the following precautions are recommended: Ensure proper use by reading and following the instructions carefully. If the unit requires service, contact an authorized HP service center—see the OmniBook Support and Service booklet. Do not attempt to make any adjustment of the unit.

  • Page 139: Regulatory Information

    Specifications and Regulatory Information Regulatory Information This section presents information that shows how the OmniBook complies with regulations in certain regions. Any modifications to the OmniBook not expressly approved by Hewlett-Packard could void the authority to operate the OmniBook in these regions.

  • Page 140: Canada

    (415) 857-1501 declares that the product(s) Hewlett-Packard Company HP OmniBook 4100 Complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.

  • Page 141: Europe

    Voltage Directive 73/23/EEC and the EMC Directive 89/336/EEC, and carries the EC mark accordingly. The HP F1454A ac adapter used with this product is designed to operate on all power systems, other than IT power systems. [1] The product was tested in a typical configuration with Hewlett-Packard personal computer peripherals.
  • Page 143 4-3, 4-4 safeguards, 3-2 SmartCard, 1-4 safety, 3-6 address saving power, 3-9 Hewlett-Packard, 8-2 status, 2-17 HP website, 1-2 troubleshooting, 7-11 Input/Output, 8-6 BIOS Advanced Power Management (APM) resources, 8-6 features, 3-2 BIOS Setup utility, 1-11, 7-7 optimizing battery life, 3-9...
  • Page 144 Boot menu (BIOS), 1-16 defaults (system), 1-12, 8-6 deleting password, 2-20, 3-10 Card Executive, 6-18 destop management, 1-17 cards. See PC Cards devices CD-ROM drive anti-static, 5-7 inserting CD, 4-6 boot order, 1-16 opening manually, 4-6 conflicts, 1-11 removing CD, 4-6 drivers, 6-2 channels (DMA), 8-7 PS/2, 1-13...
  • Page 145 2-3, 2-13 display, 2-13 status lights, 2-16 keyboard, 2-13 time-out, 1-15, 3-10 external keyboard holder (HDD), 5-4 port location, 1-6 hot keys, 2-13 external monitor HP applications, 6-19 port location, 1-7, 4-8 IDE controller, 1-13 F1 through F12, 2-13 infrared Index-3...
  • Page 146 1/0 address, 1-13 keypad (embedded), 2-14 DMA channel, 1-13 drivers (Windows 95), 6-10 laser printer, 4-10 light path, 7-8 laser safety, 8-10 mode, 1-13 LED safety, 8-10 port (connecting), 4-13 license agreement, iii port location, 1-7, 4-8 lights printing, 7-8 infrared, 7-8 InkJet printer, 4-10 keyboard status, 2-17...
  • Page 147 troubleshooting, 7-3 USB ports, 4-11 button, 2-3 ports status lights, 2-16 external devices, 4-8 OmniBook locations, 1-7, 4-8 cleaning, 8-2 power starting and stopping, 2-3 Advanced Power Management, 3-2 OmniBook Notes, 1-2 button location, 1-5 on/off button connecting ac, 1-9, 3-5 location, 1-5 conserving, 3-10 managing, 3-2...
  • Page 148 8-10 serial mouse, 4-10 support utility disk, 6-2 serial port suspend location, 1-7, 4-8 and display life, 2-10 service mode, 2-3 booklet, 1-2, 1-3 status lights, 2-16 HP service center, 8-10 time-out, 1-15, 3-10 Service Pack 3, 6-14 Index-6...
  • Page 149 System Devices menu (BIOS), 1-13 system resources undocking, 4-19 DMA channels, 8-7 Universal Serial Bus (USB) Input/Output addresses, 8-6 connecting, 4-11 memory, 8-6 USB port system interrupts, 8-6 location, 1-6 system-off button User’s Handbook (online), 1-2 location, 1-6 VGA output, 1-7, 4-8 taskbar video drivers battery, 3-4...
  • Page 150 Card Executive, 6-18 installing, 6-13 Xircom cards, 4-15 Service Pack 3, 6-14 video drivers, 6-15 zoomed video, 4-14 wireless communication, 4-13 Index-8...

This manual is also suitable for:

Omnibook 4150Omnibook 4150

Table of Contents