Related Manuals for Toshiba Satellite P10-304
Summary of Contents for Toshiba Satellite P10-304
- Page 1 Satellite User’s Manual ATELLITE P10 SATELLITE P10 SATELLITE P10 Choose freedom. Choose freedom. Choose freedom. computers.toshiba-europe.com...
- Page 2 Microsoft Corporation. Centronics is a registered trademark of Centronics Data Computer Corporation. Photo CD is a trademark of Eastman Kodak. Bluetooth is a trademark owned by its proprietor and used by TOSHIBA under license. iLINK is a trademark of Sony Corporation.
-
Page 3: Safety Instructions
User's Manual Macrovision License of Notice This product incorporates copyright protection technology that is protected by methods and claims of certain U.S. patents and other intellectual rights owned by Macrovision Corporation, and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation and is intended for home and other limited viewing uses only unless authorized by Macrovision Corporation. - Page 4 User's Manual ■ If you use an extension cable with your AC adapter, ensure that the total ampere rating of the products plugged in to the extension cable does not exceed the ampere rating of the extension cable. ■ To remove power from the computer, turn it off, remove the battery, and disconnect the AC adapter from the electrical out let.
- Page 5 User's Manual ■ When you disconnect a cable, pull on its connector or on its strain relief loop, not on the cable itself. As you pull out the connector, keep it evenly aligned to avoid bending any connector pins. Also, before you connect a cable make sure both connectors are correctly oriented and aligned.
- Page 6 User's Manual EMC Regulatory Information EU Declaration of Conformity TOSHIBA declares, that the product: Satellite P10 conforms to the following Standards: Supplementary “The product complies with the requirements of Information: the Low Voltage Directive 73/23/EEC and the EMC Directive 89/336/EEC and/or the R&TTE Directive 1999/05/EEC.”...
- Page 7 Location of the required label Sample shown below. Location of the label on the drive and manufacturing information may vary. TOSHIBA CORPORATION 1-1, SHIBAURA 1-CHOME MINATO-KU, TOKYO 105-8001, JAPAN CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT”.
- Page 8 User's Manual VORSICHT: Dieses Gerät enthält ein Laser- System und ist als “LASERSCHUTZKLASSE 1 PRODUKT” klassifiziert. Für den richtigen Gebrauch dieses Modells lesen Sie bitte die Bedienungsanleitung sorgfältig durch und bewahren diese bitte als Referenz auf. Falls Probleme mit diesem Modell auftreten, benachrichtigen Sie bitte die nächste “autorisierte Service-Vertretung”.
- Page 9 IEC 825 and EN60825 on class 1 laser product. This computer is equipped with the optical drive in the following list according to the model. Manufacturer Type Matsushita UJ-811B TEAC DV-W22E Matsushita SR-8177 TOSHIBA SD-C2612 TOSHIBA SD-R6112 Matsushita UJDA750 TOSHIBA SD-R2412 TEAC DW-224E Satellite P10 Series...
- Page 10 User's Manual Modem warning notice Conformity Statement The equipment has been approved to [Commission Decision “CTR21”] for pan- European single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point.
-
Page 11: Important Notice
Some models of the computer will come with Bluetooth technology built into it. Bluetooth was developed jointly by Ericsson, IBM, Intel, Nokia and TOSHIBA. It uses a shortwave radio frequency to connect devices such as cell phones, personal digital assistants, and computers. Essentially,... -
Page 12: General Precautions
User's Manual General Precautions TOSHIBA computers are designed to optimise safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual. -
Page 13: Lcd Display
To avoid risk of lost data, always make back-up copies of data by periodically storing it on an external storage medium. For optimum performance, use your computer product only under recommended conditions. Read additional restrictions in your bundled documents. Contact TOSHIBA Technical Service and Support for more information. Satellite P10 Series xiii... -
Page 14: Working Environment
This product was designed to fulfil the EMC (electromagnetic compatibility) requirements to be observed for so-called "Residential, commercial and light industry environments". TOSHIBA do not approve the use of this product in working environments other than the above mentioned "Residential, commercial and light industry environments". -
Page 15: Wireless Interoperability
Not all models come with a built in Wireless LAN card. Wireless Interoperability The TOSHIBA Wireless LAN Mini PCI Card products are designed to be interoperable with any Wireless LAN product that is based on Direct Sequence Spread Spectrum (DSSS) radio technology, and is compliant ■... -
Page 16: Wireless Lan And Your Health
Because Wireless LAN products operate within the guidelines found in radio frequency safety standards and recommendations, TOSHIBA believes Wireless LAN is safe for use by consumers. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature. - Page 17 User's Manual Usage Restrictions Do not use the Wireless Products for controlling equipment: ■ Equipment directly linked with human life corresponds to the following. ■ Medical equipment such as life support systems, equipment used in operations, etc. ■ Exhaust systems for gases such as poisonous gas etc. and exhaust systems for smoke.
- Page 18 User's Manual WARNING Turn OFF the Wireless Communication switch of Wireless Products in a congested place, such as a crowded commuter train. Keep this product away from a cardiac pacemaker at least 22cm. Radio waves can potentially affect cardiac pacemaker operation, thereby causing respiratory troubles.
-
Page 19: Regulatory Information
User's Manual Regulatory Information The Wireless LAN Mini PCI Card must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product. This device complies with the following radio frequency and safety standards. Satellite P10 Series... -
Page 20: Table Of Contents
Table of Contents Satellite P10 Series Table of Contents Preface ..................xxvi Manual contents.................. xxvi Conventions..................xxvii Abbreviations...................xxvii Icons ....................xxvii Keys....................xxvii Key operation ................. xxviii Display .................... xxviii Messages ..................xxviii Chapter 1 Introduction..............1-1 Equipment checklist ................1-1 Hardware ...................1-1 Software ....................1-2 Documentation ..................1-2 Features ....................1-3 Processor ..................1-3... - Page 21 Table of Contents Chapter 2 The Grand Tour............2-1 Front with the display closed ...............2-1 Left side....................2-3 Right side ....................2-4 Back side ....................2-5 Underside....................2-7 Front with the display open ..............2-8 Indicators .....................2-10 Drives ....................2-12 3 ½" diskette drive (optional) ............2-12 Optical Media drive................2-13 AC adaptor...................2-14 Chapter 3 Getting Started ............3-1...
- Page 22 Table of Contents Disk care ....................4-12 DVD/CD care ...................4-12 Diskette care..................4-12 Using the internal modem ..............4-13 IMPORTANT SAFETY INSTRUCTIONS...........4-13 Region selection ................4-14 Properties menu ................4-15 Connecting ..................4-16 Disconnecting..................4-16 LAN .......................4-17 Connecting LAN cable..............4-17 Disconnecting LAN cable ..............4-18 Wireless communications ..............4-18 Wireless LAN ...................4-18 Wireless communication switch ............4-18 Wireless communication LED............4-18...
- Page 23 Table of Contents Chapter 6 Power and Power-Up Modes .........6-1 Power conditions ..................6-2 Power indicators ...................6-2 Battery indicator ................6-2 DC IN indicator ..................6-3 Power indicator..................6-3 Battery types..................6-3 Battery pack ..................6-4 Real Time Clock battery ..............6-4 Care and use of the battery pack ............6-5 Safety precautions................6-5 Charging the batteries ...............6-8 Monitoring battery capacity...............6-9...
- Page 24 Table of Contents Chapter 8 Troubleshooting ............8-1 Problem solving process ..............8-1 Preliminary checklist................8-2 Analysing the problem ...............8-2 Hardware and system checklist............8-3 System start-up .................8-3 Self test....................8-4 Hyper-Threading Technology Incompatibility........8-5 Power ....................8-5 Overheating power down ..............8-5 AC power...................8-5 Battery ....................8-6 Keyboard ...................8-7 LCD panel..................8-7 Hard disk drive ..................8-8 DVD-ROM drive .................8-8...
- Page 25 Table of Contents Appendix A Specifications ............A-1 Appendix B AC Power Cord and Connectors ....... B-1 Appendix C Keyboard Layouts ..........C-1 Appendix D Display Modes .............D-1 Appendix E If your computer is stolen........E-1 Appendix F ASCII Character Codes ........
-
Page 26: Preface
Preface Satellite P10 Series Preface Congratulations on your purchase of the Satellite P10 series computer. This powerful notebook computer provides excellent expansion capability, including multimedia devices, and it is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your Satellite P10 series computer. -
Page 27: Conventions
Preface Chapter 5, The Keyboard, describes special keyboard functions including the keypad overlay and hotkeys. Chapter 6, Power and Power-Up Modes, gives details on the computer’s power resources. Chapter 7, Optional Devices, describes the optional hardware available. Chapter 8, Troubleshooting, provides helpful information on how to perform some diagnostic tests, and suggests courses of action if the computer doesn’t seem to be working properly. -
Page 28: Key Operation
Preface Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C. -
Page 29: Chapter 1 Introduction
Basic features are described in a separate pamphlet. Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use. -
Page 30: Software
■ Online Help ■ Product Recovery CD-ROM or DVD-ROM The system may not function properly if you use drivers that are not preinstalled or distributed by TOSHIBA. Documentation ■ Your computer’s documentation: ■ Satellite P10 Series Personal Computer User’s Manual ■... -
Page 31: Features
Introduction Features The Satellite P10 series computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability. This computer incorporates the following features and benefits:... -
Page 32: Power
Introduction Power Battery pack 12 cells Li-Ion 18650 size smart battery pack with 14.8V x 6450mAh capacity. Approximately 4 hours charging time to 100% (system off). Discharge time with main battery in standby mode is approximately 2 days. Discharge time with main battery in shutdown mode is approximately 1 month. -
Page 33: Pcmcia Card
Introduction PCMCIA Card PCMCIA Card One type II card socket MODEM/LAN Card Card bus card ACPI 1.0b compliant Ports (depending on configuration) External monitor 15-pin analog VGA port supports VESA DDC2B compatible functions. Universal Serial Bus The computer has three Universal Serial Bus (USB) ports that comply with the USB 2.0 standard, which enables data transfer speeds more than 40 times faster than USB 1.1 (which... -
Page 34: Multimedia
Introduction Multimedia Sound system Incorporates a Wave Table Synthesizer for advanced sound applications including 3D games, DVD movie playback and Internet communications. TV-out button Sets your display device to TV (video-out). Press it to switch back and forth between it and the LCD. -
Page 35: Communications
Introduction Communications Modem An internal modem provides capability for data and fax communication. It supports V.90 or V.92 depending on the region. The speed of data transfer and fax depends on analog telephone line conditions. It has a modem jack for connecting to a telephone line. -
Page 36: Special Features
Introduction Special features The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use. Hotkeys Key combinations let you quickly modify the system configuration directly from the keyboard without running a system configuration program. -
Page 37: Utilities
There are two ways to display the Windows XP TOSHIBA Power Management Utility Control Panel. The default is Category View. TOSHIBA Power Management Utility is under the Performance and Maintenance item. TOSHIBA Console TOSHIBA Console is a graphical user interface that provides easy access to help and services. -
Page 38: Options
TOSHIBA dealer for details. An additional battery pack can be purchased Battery Pack from your TOSHIBA dealer. Use it as a spare to increase your computer operating time. AC Adaptor If you use your computer at more than one site... -
Page 39: Chapter 2 The Grand Tour
The Grand Tour Satellite P10 Series Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Front with the display closed The figure below shows the computer front with its display panel in the closed position. - Page 40 The Grand Tour Mode Press this button to cycle between various CD, DVD and audio functions. Refer to Chapter 4, Operating Basics, for details. Previous/Fast Skips back to previous tracks. If held down while Rewind a song is playing, it fast rewinds through it. Refer to Chapter 4, Operating Basics, for details.
-
Page 41: Left Side
The Grand Tour Left side The figure below shows the computer left side. LINE-IN JACK HEADPHONE JACK WIRELESS MICROPHONE JACK COMMUNICATION SWITCH The left side of the computer Headphone Jack The Headphone Jack lets you connect stereo headphones or other audio-output devices such as external speakers. -
Page 42: Right Side
The Grand Tour Right side The figure below shows the computer right side. INFRARED PORT (INFRARED MODEL ONLY) SD CARD SLOT SECURITY LOCK USB PORT PC CARD SLOT i.LINK PORT The right side of the computer Universal Serial Bus You can use USB2.0 and USB1.1 devices such (USB) Port as USB HDD, USB printer, USB keyboard, USB mouse, USB scanner. -
Page 43: Back Side
The Grand Tour Back side The figure below shows the computer back panel. EXTERNAL MONITOR MODEM JACK USB PORT PORT LAN JACK PARALLEL PORT TV OUT DC IN 19V JACK The back side of the computer You can use USB2.0 and USB1.1 devices such Universal Serial Bus (USB) Ports as USB HDD, USB printer, USB keyboard, USB... - Page 44 The Grand Tour LAN Jack This jack lets you connect to a LAN. The adaptor Ether has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T) and Fast Ethernet LAN (100 megabits per second, 100BASE-Tx). Do not cover the cooling vent or otherwise obstruct it. Doing so may cause the computer to overheat and result in damage.
-
Page 45: Underside
BATTERY LATCH BATTERY WIRELESS LAN SOCKET OPTICAL MEDIA DRIVE The bottom of the computer Wireless LAN Socket Consult your TOSHIBA dealer for installation of a Wireless LAN card. Expansion Memory Use this socket to install a memory module to Socket increase your computer’s memory. -
Page 46: Front With The Display Open
The figure below shows the front of the computer with the display open. To open the display, slide the display latch on the front of the display and lift up. Position the display at a comfortable viewing angle. TOSHIBA DISPLAY KEYBOARD... - Page 47 If the computer’s power is off, you can press this button to turn on the computer’s power and launch the browser automatically in one step. TOSHIBA Console You can associate an application to this button Button for automatic launch. If the computer is off, pressing this button starts the computer and launches the associated program automatically.
-
Page 48: Indicators
The Grand Tour Indicators The figures below show the system indicator lights, which light when various computer operations are in progress. HARD DRIVE OPTICAL DISC DRIVE WIRELESS COMMUNICATION SD CARD The system indicators Hard Drive The Hard Drive LED indicates that the HDD is being accessed. - Page 49 The Grand Tour DC-IN POWER BATTERY The keyboard indicators DC-IN The DC-IN LED indicates the computer is connected to the AC adapter and it is plugged into an AC power source. Power The Power LED flashes amber while the system is in Standby mode.
-
Page 50: Drives
The Grand Tour Drives This section describes the Optical Disc Drive and the USB FDD (optional). 3 ½" diskette drive (optional) DISK-IN-USE INDICATOR DISKETTE SLOT EJECT BUTTON The diskette drive The 3 ½" diskette drive lets you use either double density (720 KB) or high density (1.44 MB) 3 ½"... -
Page 51: Optical Media Drive
The Grand Tour Optical Media drive The full-size Optical Media drive module lets you play from and record data to rewritable DVDs and CDs as well as run either 12 cm (4.72") or 8 cm (3.15") discs without using an adaptor. Use the preinstalled software, Drag ’n Drop, for writing DVDs and CDs. -
Page 52: Ac Adaptor
See Chapter 6, Power and Power-Up Modes, for details. The AC adaptor Use of the wrong adaptor could damage your computer. TOSHIBA assumes no liability for any damage in such case. The current rating for the computer is 19 VDC, 6.3 amperes. -
Page 53: Chapter 3 Getting Started
Getting Started Satellite P10 Series Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: ■ Setting up your work space — for your health and safety Connecting the AC adaptor ■... -
Page 54: General Conditions
Getting Started General conditions In general, if you are comfortable, so is your computer, but read the following to make sure your work site provides a proper environment. ■ Make sure there is adequate space around the computer for proper ventilation. -
Page 55: Seating And Posture
Getting Started Seating and posture The height of your chair in relation to the computer and keyboard as well as the support it gives your body are primary factors in reducing work strain. Refer to the following tips and to the figure below. Posture and positioning of the computer ■... -
Page 56: Work Habits
AC adaptor to charge the battery pack, refer to Chapter 6, Power and Power-Up Modes. Use of the wrong adaptor could damage your computer. TOSHIBA assumes no liability for any damage in such case. The current rating for the computer is 19 VDC, 6.3 amperes. - Page 57 Getting Started 1. Connect the power cord to the AC adaptor. Connecting the power cord to the AC adaptor 2. Connect the AC adaptor to the DC output plug to the DC IN input port on the back of the computer. Connecting the adaptor to the computer 3.
-
Page 58: Opening The Display
Getting Started Opening the display The display panel can be rotated in a wide range of angles for optimal viewing. 1. Slide the display latch on the front of the computer to the right to unlatch the display panel. Opening the display 2. -
Page 59: Turning On The Power
Getting Started Turning on the power This section describes how to turn on the power. After you turn on the power for the first time, do not turn it off until you have set up the operating system. Refer to the section Starting up for the first time in this chapter. -
Page 60: Turning Off The Power
Getting Started Turning off the power The power can be turned off in one of the following modes: Shut down (Boot), Hibernation or Standby mode. Shut Down mode (Boot mode) When you turn off the power in Shut Down mode no data is saved and the computer will boot to the operating system’s main screen. -
Page 61: Starting Hibernation
For the computer to shut down in hibernation mode, the hibernation feature must be enabled in two places in TOSHIBA Power Management utility: the Power Save Modes tab and the Advanced tab. Otherwise, the computer will shut down in Standby mode. -
Page 62: Standby Mode
To prevent the computer from automatically entering standby mode, disable Standby in the TOSHIBA Power Management Utility. Open the TOSHIBA Power Management Utility and click the Power Save Modes tab. Next select either an AC Power or Battery Power option and then click details. - Page 63 1. Click start, click Turn Off Computer and click Stand by. 2. Close the display panel. This feature must be enabled. To enable it, select the TOSHIBA Power Management Utility icon in the Control Panel and select the Advanced tab and then set your Power Buttons options to Standby.
-
Page 64: Restarting The Computer
1. Load the Product Recovery CD-ROM or DVD-ROM in the drive and turn off the computer’s power. 2. Power on your computer, when In Touch with Tomorrow TOSHIBA appears, press F12 key. Boot Menu will appear. 3. Use the up or down cursor key to select the CD-ROM/DVD drive in the display menu. -
Page 65: Chapter 4 Operating Basics
Operating Basics Satellite P10 Series Chapter 4 Operating Basics This chapter gives information on basic operations including using the Touch pad, optical media drives, the internal modem, LAN, wireless LAN. It also provides tips on caring for your computer and on heat dispersal. Using the Touch pad To use the Touch pad, simply move your finger tip across it in the direction you want the on-screen pointer to go. - Page 66 Operating Basics Two buttons below the keyboard are used like the buttons on a mouse pointer. Press the left button to select a menu item or to manipulate text or graphics designated by the pointer. Press the right button to display a menu or other function depending on the software you are using.
-
Page 67: Using Optical Media Drives
Operating Basics Using optical media drives The computer can be configured with one of the following optical media drives: DVD Multi drive, DVD-ROM, CD-RW/DVD, or DVD-R/RW. The text and illustrations in this section refer primarily to the DVD-ROM drive. However, operation is the same for the other drives. The full-size drive provides high-performance execution of DVD-ROM or CD-ROM-based programs. -
Page 68: Loading Compact Discs
Operating Basics Loading compact discs To load a DVD/CD, follow the steps below and refer to the figures below. 1. Turn on the power. 2. a. Press the eject button to open the drawer slightly. Pressing the eject button b. Pressing the eject button will not open the drawer when the computer’s power is off. - Page 69 Operating Basics 3. Grasp the drawer gently and pull until it is fully opened. Pulling the drawer open 4. Lay the DVD/CD, label side up, in the drawer. Inserting a DVD/CD Be careful not to touch the lens or the area around it. Doing so could cause the drive to malfunction.
- Page 70 Operating Basics 5. Press gently at the centre of the DVD/CD until you feel it click into place. The DVD/CD should lie below the top of the spindle, flush with its base. 6. Push the centre of the drawer to close it. Press gently until it locks in place.
-
Page 71: Removing Compact Discs
Operating Basics Removing compact discs To remove the DVD/CD, follow the steps below and refer to the figure below. Do not press the eject button while the computer is accessing the DVD drive. Wait for the Diskette/Optical Media indicator to go out before you open the drawer. -
Page 72: Cd/Digital Mode Button
Operating Basics CD/Digital Mode button This section describes how to use the CD/DVD/Audio Control Buttons to control the optical media drive and Digital Audio Data. Whether your computer is turned on or off, the CD/DVD/Audio control buttons are locked by default. To unlock them, press the CD/Digital mode button for more than 3 seconds. -
Page 73: Cd/Dvd/Audio Control Buttons
Operating Basics CD/DVD/Audio control buttons In addition to the power button, the following four buttons control functions of the optical media drive and Digital Audio Data: 1. Play/Pause Starts or pauses play. 2. Stop Stops play. Advances to the next track, chapter or data 3. -
Page 74: Before Writing
Taiyo Yuden Co. Ltd. DVD-RW Victor Company of Japan, Ltd. (JVC). TDK Corporation. TOSHIBA has confirmed the operation of CD-R, CD-RW, DVD-RW media of the manufacturers above. Operation of other media cannot be guaranteed. ■ DVD/CD-RW can generally be rewritten about 1000 times. However, the actual number of rewrites is affected by the quality of the media. -
Page 75: When Writing Or Rewriting
Operating Basics When writing or rewriting Note when you write or rewrite a CD-R, CD-RW, DVD-R, DVD-RW, or DVD-RAM: ■ Always copy data from the HDD to the DVD/CD. Do not use cut-and-paste. The original data will be lost if there is a write error. ■... -
Page 76: Disk Care
Operating Basics Disk care This section provides tips on protecting data stored on your DVD/CDs and diskettes. DVD/CD care Handle your DVD/CDs with care. The following simple precautions will increase the lifetime of your DVD/CDs and protect the data stored on them: 1. -
Page 77: Using The Internal Modem
Operating Basics Using the internal modem This section describes how to make settings and connect the modem. Refer to the computer’s online help files for more information. Refer also to the online help files for your modem software. The internal modem does not support the voice functions described in the help files. -
Page 78: Region Selection
1. Point to All Programs, point to TOSHIBA Internal Modem and click Region Select Utility. Do not use the Country/Region Select function in the Modem setup utility in the Control Panel if the function is available. -
Page 79: Properties Menu
Operating Basics Properties menu Click the icon with the secondary mouse button to display the following menu. The properties menu Setting You can enable or disable the following settings: AutoRun Mode Region Select Utility starts automatically when you start up the operating system. -
Page 80: Connecting
Operating Basics Connecting To connect the internal modem cable, follow the steps below. In case of a lightning storm, unplug the modem cable from the telephone jack. Do not connect the modem to a digital telephone line. A digital line will damage the modem. -
Page 81: Lan
Operating Basics The computer is equipped with LAN circuits that support Ethernet LAN (10 megabits per second, 10BASE-T) and Fast Ethernet LAN (100 megabits per second, 100BASE-TX). This section describes how to connect/disconnect to a LAN. Do not install or remove an optional memory module while Wake-up on LAN is enabled. -
Page 82: Disconnecting Lan Cable
Operating Basics Disconnecting LAN cable To disconnect the LAN cable, follow the steps below. 1. Pinch the lever on the connector in the computer’s LAN jack and pull out the connector. 2. Disconnect the cable from the LAN hub in the same manner. Check with your LAN administrator before disconnecting from the hub. -
Page 83: Tv-Out
Operating Basics TV-Out Use this jack to connect to a television. Be sure to use a 4 pin type S-video cable. Setting up more than one display The following applies for the GeForce FX Go5100, GeForce FX Go5200, and the GeForce FX Go5600 though as written is describes the GeForce FX Go5200. -
Page 84: Multiple Display Properties
Operating Basics Multiple display properties If the GeForce FX Go5200 tab is not visible when you click the Advanced button on the Settings tab of the Display Properties window, you can access it by clicking the green tab on the left side of the window: Satellite P10 Series 4-20... - Page 85 Operating Basics 1. Select the monitor you wish to use from the drop down list. 2. Open the GeForce FX Go5200 tab by clicking the green button. Selecting an option from the GeForce FX Go5200 tab presents you with the options panel, which you can use to configure the selected monitor.
-
Page 86: Cleaning The Computer
Operating Basics Cleaning the computer To help ensure long, trouble-free operation, keep the computer free of dust and use care with liquids around the computer. ■ Be careful not to spill liquids into the computer. If the computer does get wet, turn the power off immediately and let the computer dry completely before you turn it on again. -
Page 87: Chapter 5 The Keyboard
The Keyboard Satellite P10 Series Chapter 5 The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with. -
Page 88: F1 ... F12 Function Keys
American keyboard driver. Soft keys: Fn key combinations The Fn (function) is unique to TOSHIBA computers and is used in combination with other keys to form soft keys. Soft keys are key combinations that enable, disable or configure specific features. -
Page 89: Emulation Keys
The Keyboard Emulation keys PrtSc Pause Scroll SysReg lock Break & Bk Sp PgUp Home Lock PgDn Home PgUp Enter CapsLock < > Shift Shift PgDn Enter Ctrl Ctrl A 101-key enhanced keyboard layout The keyboard is designed to provide all the features of the 101-key enhanced keyboard, shown above. -
Page 90: Hotkeys
The Keyboard Hotkeys Volume Mute Turns the volume on and off. Instant Security Enters screen saver mode and blanks the screen. To restore your desktop, press any key or use the Touch Pad. Power Save Modes Displays the power save modes and lets you change the power settings. -
Page 91: Windows Special Keys
The Keyboard Windows special keys The keyboard provides two keys that have special functions in Windows XP. One activates the Start menu and the other has the same function as the secondary mouse button. This key activates the Windows XP Start menu. This key has the same function as the secondary mouse button. -
Page 92: Temporarily Using Normal Keyboard (Overlay On)
The Keyboard Numeric mode To turn on the Numeric mode, press Fn + F11 (Numeric mode indicator lights). Now try numeric data entry using the keys in the figure below. Press Fn + F11 again to turn off the overlay. The numeric keypad overlay Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard... -
Page 93: Temporarily Changing Modes
The Keyboard Temporarily changing modes If the computer is in Numeric mode, you can switch temporarily to Arrow mode by pressing a shift key. If the computer is in Arrow mode, you can switch temporarily to Numeric mode by pressing a shift key. Generating ASCII characters Not all ASCII characters can be generated using normal keyboard operation. -
Page 94: Chapter 6 Power And Power-Up Modes
Power and Power-Up Modes Satellite P10 Series Chapter 6 Power and Power-Up Modes The computer’s power resources include the AC adaptor and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes. -
Page 95: Power Conditions
DC IN off ■ Operates Battery charge is below low battery ■ Alarm sounds (depending — trigger point on the Toshiba Power Management Utility setting) ■ LED: Battery flashes amber DC IN off Battery charge Computer goes into —... -
Page 96: Dc In Indicator
Power and Power-Up Modes Check the Battery indicator to determine the status of the battery. The following indicator lights indicate the battery status: Flashing amber The battery charge is low. The AC adaptor must be connected to recharge the battery. Amber Indicates the AC adaptor is connected and charging the battery. -
Page 97: Battery Pack
Press <F1> to resume, <F2> to Setup The computer’s RTC battery is a lithium ion battery and should be replaced only by your dealer or by a TOSHIBA service representative. The battery can explode if not properly replaced, used, handled or disposed of. -
Page 98: Care And Use Of The Battery Pack
Power and Power-Up Modes Care and use of the battery pack The battery pack is a vital component of portable computing. Taking proper care of it will help ensure longer operating time on battery power as well as a longer life for your battery pack. Follow the instructions in this section carefully to ensure safe operation and maximum performance. - Page 99 Never use the computer again until it has been checked by a TOSHIBA service provider. It might generate smoke or fire, or the battery pack might rupture. 3. Make sure the battery is securely installed in the computer before attempting to charge the battery pack.
- Page 100 2. Never dispose of battery packs with normal trash. Bring them to your TOSHIBA dealer or to another recycling centre to save resources and prevent environ- mental damage. Cover the terminals with electrical tape to prevent short-circuits, which could cause the battery pack to ignite or rupture.
-
Page 101: Charging The Batteries
Power and Power-Up Modes Charging the batteries When the power in the battery pack becomes low, the Battery indicator flashes amber indicating that only a few minutes of battery power remain. If you continue to use the computer while the Battery indicator flashes, the computer enables Hibernation mode (so you don’t lose data) and automatically turns off. -
Page 102: Monitoring Battery Capacity
Monitoring battery capacity Remaining battery power can be monitored by the TOSHIBA Power Management Utility. Refer to Utilities in Chapter 1, Introduction. Wait for a moment after turning on the computer before trying to monitor the remaining operating time. -
Page 103: Maximizing Battery Operating Time
Power and Power-Up Modes Maximizing battery operating time A battery’s usefulness depends on how long it can supply power on a single charge. How long the charge lasts in a battery depends on: ■ How you configure the computer (for example, whether you enable battery power saving options). -
Page 104: Replacing The Battery Pack
5. Slide the battery latch to the right, then pull the battery out of the battery bay. Removing the battery pack For environmental reasons, do not throw away a spent battery pack. Please return spent battery packs to your TOSHIBA dealer. Satellite P10 Series 6-11... -
Page 105: Installing The Battery Pack
The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. 1. Turn the computer’s power off. 2. Disconnect all cables connected to the computer. -
Page 106: Panel Power Off/On
Power and Power-Up Modes Panel power off/on You can set up your computer so that power turns off automatically when you close the display panel. When you open the panel, power turns on in Standby or Hibernation mode but not in boot mode. If the panel power off function is enabled and you use Shut down Windows, do not close the display until the shut down function is completed. -
Page 107: Chapter 7 Optional Devices
Optional Devices Satellite P10 Series Chapter 7 Optional Devices Optional devices can expand the computer’s capabilities and its versatility. This chapter describes connection or installation of the following types of devices: Memory/Cards ■ Memory modules ■ PC cards ■ SD Cards Power devices ■... -
Page 108: Pc Cards
The computer is equipped with a PC card expansion slot that can accommodate one 5 mm Type II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slots support 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards. -
Page 109: Removing A Pc Card
Optional Devices Removing a PC card 1. Click the Safety Remove Hardware icon on the Task Bar. 2. Click the PC card you want to remove. 3. Press the eject button of the PC card to extend it. 4. Press the extended eject button to pop the card out slightly. 5. -
Page 110: Sd Memory/Io Cards
Optional Devices SD Memory/IO Cards The computer is equipped with an SD card slot that can accommodate Secure Digital flash memory cards with capacities of 8 MB, 16 MB, 32 MB, 64 MB, 128 MB, 256 MB, and 512 MB. SD cards let you easily transfer data from devices, such as digital cameras and Personal Digital Assistants, that use SD card flash-memory. -
Page 111: Removing An Sd Card
Optional Devices Removing an SD card To remove an SD card, follow the steps below. 1. Click the Safety Remove Hardware icon on the Task Bar. 2. Click the SD Card you want to remove If you have additional external storage devices connected, such as a digital camera, then be sure you select the correct removable disk. -
Page 112: Memory Expansion
If you want to upgrade system memory, you should only use certified modules. Ask your vendor or check the TOSHIBA web site for a list of approved memory products. Installing memory module If you use the computer for a long time, the memory modules will become hot. - Page 113 Optional Devices 5. Slide your fingernail or a thin object under the cover and lift it off. Removing the memory module socket cover 6. Fit the module’s connectors into the computer’s connectors at about a 45 degree angle and press the module carefully to ensure a firm connection.
- Page 114 Optional Devices 7. Push the module down so it lies flat. Latches on either side will click into place to secure the module. Installing a module 8. Seat the cover and secure it with two screws. 9. Replace the battery pack as described in Chapter 6, Power and Power-Up Modes.
-
Page 115: Removing Memory Module
Optional Devices Removing memory module If you use the computer for a long time, the memory modules will become hot. In this case, let the memory modules cool to room temperature before you replace them. To remove the memory module, make sure the computer is in boot mode then: 1. -
Page 116: Additional Battery Pack
Optional Devices Additional battery pack You can increase the portability of the computer with additional battery packs. If you’re away from an AC power source and your battery runs low, you can replace it with a freshly charged battery. See Chapter 6, Power and Power-Up Modes. -
Page 117: External Monitor
Optional Devices External monitor An external analog monitor can be connected to the external monitor port on the computer. The computer supports VGA and Super VGA video modes. To connect a monitor, follow the steps below. 1. Turn the computer off. 2. - Page 118 Optional Devices To set the TV type, follow the steps below: 1. Click Start > Settings > Control Panel. 2. Choose Display to open the Display Properties dialog box. 3. Click the Settings tab. 4. Select the Multiple Monitors options from the Display menu. 5.
-
Page 119: I.link (Ieee1394)
Optional Devices 8. Click the GeForce FX Go5200 (GeForce FX Go5100 or GeForce FX Go5600, depending on your configuration) tab to adjust the monitor’s other properties. i.LINK (IEEE1394) i.LINK (IEEE1394) is used for high-speed data transfer for a range of compatible devices such as: ■... -
Page 120: Precautions
Optional Devices Precautions ■ Make a back-up of your data before transferring it to the computer. There is a possibility that the original data will be damaged. There is a particular risk that some frames will be deleted in the case of digital video transfer. -
Page 121: Security Lock
Optional Devices Security lock A security lock enables you to anchor your computer to a desk or other heavy object to help prevent unauthorized removal of the computer. Attach one end of a cable to the desk and the other end to the security lock slot on the right side of the computer. -
Page 122: Satellite P10 Series
Troubleshooting Satellite P10 Series Chapter 8 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring. -
Page 123: Preliminary Checklist
Troubleshooting Preliminary checklist Consider the simplest solution first. The items in this checklist are easy to fix and yet can cause what appears to be a serious problem. ■ Make sure you turn on all peripheral devices before you turn on the computer. -
Page 124: Hardware And System Checklist
Troubleshooting Software The problems may be caused by your software or diskette. If you cannot load a software package, the media may be damaged or the program might be corrupted. Try loading another copy of the software. If an error message appears while you are using a software package, check the software documentation. -
Page 125: Self Test
BIOS. If any of the following conditions are present, the self test failed: ■ The computer stops and does not proceed to display information or messages except the TOSHIBA logo. ■ Random characters appear on the screen, and the system does not function normally. -
Page 126: Hyper-Threading Technology Incompatibility
Technology (HTT). If an application does not work with HTT, try disabling it as described below. 1. Turn the computer on. 2. Press F2 to enter the BIOS setup menu when the TOSHIBA logo appears on the screen. 3. Under the Advanced menu, in Hyper Threading Technology, select Disable. -
Page 127: Battery
If you do not think the battery is at the end of its operating life, see your dealer. Battery doesn’t power Check the power consumption settings in the the computer as long TOSHIBA Power Management Utility. Consider as expected using a power saving mode. Satellite P10 Series... -
Page 128: Keyboard
Troubleshooting Keyboard Keyboard problems can be caused by your setup configuration. For more information refer to Chapter 5, The Keyboard. Problem Procedure Some letter keys Check that the numeric keypad overlay is not produce numbers selected. Press Fn + F10 and try typing again. Output to screen is Make sure the software you are using is not garbled... -
Page 129: Hard Disk Drive
Troubleshooting Hard disk drive Problem Procedure Computer does not Insert a system diskette and reboot. boot from hard drive There may be a problem with your operating system files. Refer to your OS documentation. Slow performance Your files may be fragmented. Run SCANDISK and defragmenter to check the condition of your files and disk. -
Page 130: Cd-Rw/Dvd-Rom Drive
Troubleshooting Problem Procedure Some CDs run The software or hardware configuration may be correctly, but others causing a problem. Make sure the hardware do not configuration match’s your software’s needs. Check the disc’s documentation. Check the type of disc you are using. The drive supports: CD-DA, CD-ROM, CD-R/W, CD-R, CD-ROM XA (except ADPCM), CD-I Ready, PhotoCD,... - Page 131 Chapter 2, The Grand Tour. Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: Use only media recommended by TOSHIBA. Do not use the mouse or keyboard during writing. Use only the software supplied with the computer for recording.
-
Page 132: Dvd Multi Drive
Troubleshooting DVD Multi drive For more information, refer to Chapter 2, The Grand Tour, and to Chapter 4, Operating Basics. Problem Procedure You cannot access a Make sure the drive’s drawer is securely closed. disc in the drive Press gently until it clicks into place. Open the drawer and make sure the disc is properly seated. -
Page 133: Dvd-R/Rw Drive
Procedure Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: ■ Use only media recommended by TOSHIBA. ■ Do not use the mouse or keyboard during writing. ■ Use only the software supplied with the computer for recording. - Page 134 Chapter 2, The Grand Tour. Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: ■ Use only media recommended by TOSHIBA. ■ Do not use the mouse or keyboard during writing. ■ Use only the software supplied with the computer for recording.
-
Page 135: Diskette Drive
Troubleshooting Diskette drive For more information on the diskette drive, refer to Chapter 2, The Grand Tour. For information on diskette care refer to Chapter 4, Operating Basics. Problem Procedure Some programs run The software or hardware configuration may be correctly, but others causing a problem. -
Page 136: Printer
Troubleshooting Printer Refer also to the Parallel printer section in Chapter 7, Optional Devices, and to the troubleshooting and other relevant sections in your printer and software documentation. Problem Procedure Printer does not turn Check that the printer is connected to an electric. -
Page 137: Sd Memory/Io Cards
Troubleshooting SD Memory/IO Cards Refer also to Chapter 7, Optional Devices. Problem Procedure SD card error occurs Reseat the SD card to make sure it is firmly connected. Check the card’s documentation. If problems persist, contact your dealer. Sound system Problem Procedure No sound is heard... -
Page 138: Usb Mouse
Troubleshooting Problem Procedure Try changing the speed setting in the mouse The mouse pointer control utility. moves too fast or too slow 1. Open the Control Panel, select the Mouse icon and press Enter. 2. Click the Pointer Options tab. 3. -
Page 139: Usb
Troubleshooting Refer also to your USB device’s documentation. Problem Procedure USB device does not Check for a firm cable connection between the work USB ports on the computer and the USB device. Make sure the USB device drivers are properly installed. -
Page 140: Standby/Hibernation
Troubleshooting Standby/Hibernation Problem Procedure The system will not Is Windows Media™ Player open? The system enter might not enter Standby/Hibernation, if Windows Standby/Hibernation Media Player is either playing a selection or finished playing a selection. Close Windows Media Player before you select Standby/ Hibernation. -
Page 141: Modem
Troubleshooting Modem Problem Procedure Communication Make sure the computer’s internal modem software can’t initialise settings are correct. Refer to Phone and Modem the modem Options Properties in the Control Panel. You can hear a dial If the call is going through a PBX machine, make tone but can’t make a sure the communication application’s tone dial call... -
Page 142: Wireless Lan
Troubleshooting Wireless LAN If the following procedures do not restore LAN access, consult your LAN administrator. For more information on wireless communication, refer to Chapter 4, Operating Basics. Problem Procedure Cannot access Make sure the computer’s wireless Wireless LAN communication switch is set to on. Use the Config Free program that comes pre- installed in your computer to see LAN status. -
Page 143: I.link (Ieee1394)
If problems persist, contact your dealer. If you need further assistance If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call... -
Page 144: Appendix A Specifications
Specifications Satellite P10 Series Appendix A Specifications This appendix summarizes the computer’s technical specifications. Environmental Requirements Conditions Ambient temperature Relative humidity Operating 5°C to 30°C 10% to 90% Non-operating -20°C to 65°C Conditions Altitude (from sea level) Operating sea level to 3,000 meters Non-operating sea level to 10,000 meters Built-in Modem... - Page 145 Specifications Communication specifications Communication Data: Full duplex system Fax: Half duplex Communication Data: protocol ITU-T-Rec (Former V.21/V.22/V.22bis/V.32/ CCITT) V.32bis/V.34/V.90/V.92 (only for USA and Canada) Bell 103/212A ITU-T-Rec (Former V.17/V.29/V.27ter/ V.21 CCITT) Communication Data transmission and reception 300/1200/2400/4800/ 7200/9600/12000/ speed 14400/16800/19200/ 21600/24000/26400/ 28800/31200/33600 bps Data reception only with V.90/V.92 28000/29333/30666/ 32000/33333/34666/...
-
Page 146: Appendix B Ac Power Cord And Connectors
AC Power Cord and Connectors Satellite P10 Series Appendix B AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Minimum 2 metres... - Page 147 AC Power Cord and Connectors Germany: Italy: The Netherlands: KEMA Norway: NEMKO Sweden: SEMKO Switzerland: United Kingdom: In Europe, power cords must be VDE type, H05VVH2-F and two conductor. For the United States and Canada, plug configuration must be a 2-15P (250 V) or 1-15P (125 V) as designated in the U.S.
-
Page 148: Appendix C Keyboard Layouts
Keyboard Layouts Satellite P10 Series Appendix C Keyboard Layouts Arabic Belgian User's Manual Satellite P10 Series... - Page 149 Keyboard Layouts Danish French German Satellite P10 Series...
- Page 150 Keyboard Layouts Greek Hebrew Italian Satellite P10 Series...
- Page 151 Keyboard Layouts Norwegian Polish Portuguese Satellite P10 Series...
- Page 152 Keyboard Layouts Russian Spanish Swedish Satellite P10 Series...
- Page 153 Keyboard Layouts Swiss-German Turkish UK English Satellite P10 Series...
- Page 154 Keyboard Layouts US English Satellite P10 Series...
-
Page 155: Appendix D Display Modes
Display Modes Satellite P10 Series Appendix D Display Modes The Satellite P10’s nVIDIA GeForce FX Go5200 Graphics Controller lets you switch resolutions by right-clicking on your desktop and choosing the Properties options. Or, if enabled, click the monitor icon in the system notification area and then select the desired resolution from the pop-up menu. -
Page 156: If Your Computer Is Stolen
What is your address, phone, and fax number? To register the theft, please follow these procedures: ■ Fill in the TOSHIBA Theft Registration form (or a copy of it) below. ■ Attach a copy of your receipt showing where your computer was purchased. -
Page 157: Toshiba Theft Registration
If your computer is stolen TOSHIBA Theft Registration Send to: TOSHIBA Europe GmbH Technical Service and Support Leibnizstr. 2 93055 Regensburg Germany Fax number: +49 (0) 941 7807 925 Country stolen: Machine type: (e.g. Satellite P10) Model number: (e.g. PSA10E YXT) Serial number: (e.g. -
Page 158: Appendix F Ascii Character Codes
ASCII Character Codes Satellite P10 Series Appendix F ASCII Character Codes This appendix shows the American Standard Code for Information Interchange (ASCII) on the following pages. The characters in the IBM char column appear on your display when you type the corresponding ASCII code (as described in Chapter 5, The Keyboard). - Page 159 ASCII Character Codes Sort Ctrl code code char char ¶ § ▲ ▼ Satellite P10 Series...
- Page 160 ASCII Character Codes Sort Sort code code char code code char space “ & ’ < > Satellite P10 Series...
- Page 161 ASCII Character Codes Sort Sort code code char code code char ’ Ç ü é â ä à å ç ê ë è ï î ì Ä Å É æ Æ ô ö ò û ù ÿ Ö Ü ¢ £...
- Page 162 ASCII Character Codes Sort Sort code code char code code char á í ó ú ñ Ñ ¿ ¡ « » Satellite P10 Series...
- Page 163 ASCII Character Codes Sort code code char ß Satellite P10 Series...
-
Page 164: Glossary
Glossary Satellite P10 Series Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference. adaptor: A device that provides an interface between two dissimilar electronic devices. For example, the AC adaptor modifies the power from a wall outlet for use by the computer. - Page 165 Glossary asynchronous: Lacking regular time relationship. As applied to computer communications, asynchronous refers to the method of transmitting data that does not require a steady stream of bits to be transmitted at regular time intervals. AUTOEXEC.BAT: A batch file that executes a series of MS-DOS commands and programs each time you start the computer.
- Page 166 Glossary cache memory: High speed memory which stores data that increases processor speed and data transfer rate. When the CPU reads data from main memory, it stores a copy of this data in cache memory. The next time the CPU needs that same data, it looks for it in the cache memory rather than the main memory, which saves time.
- Page 167 Glossary commands: Instructions you enter at the terminal keyboard that direct the actions of the computer or its peripheral devices. communications: The means by which a computer transmits and receives data to and from another computer or device. Compact Flash: A small removable mass storage device, designed with flash technology, a non-volatile storage solution that does not require a battery to retain data indefinitely.
- Page 168 Glossary data bits: A data communications parameter controlling the number of bits (binary digits) used to make up a byte. If data bits = 7 the computer can generate 128 unique characters. If data bits = 8 the computer can generate 256 unique characters. data: Information that is factual, measurable or statistical that a computer can process, store, or retrieve.
- Page 169 Glossary DVD-RAM: A Digital Versatile Disc Random Access Memory is a high- capacity, high performance disc that lets you store large volumes of data. The DVD drive uses a laser to read data from the disc. DVD-ROM: A Digital Versatile Disc Read Only Memory is a high capacity, high performance disc suitable for play back of video and other high-density files.
- Page 170 See also software and firmware. HW Setup: A TOSHIBA utility that lets you set the parameters for various hardware components. hertz: A unit of wave frequency that equals one cycle per second.
- Page 171 Glossary I/O devices: Equipment used to communicate with the computer and transfer data to and from it. I/O: Input/output. Refers to acceptance and transfer of data to and from a computer. icon: A small graphic image displayed on the screen or in the indicator panel.
- Page 172 100,000 simple logic gates on a single chip. 2) An integrated circuit that uses the large scale integration. magiCDisc: A TOSHIBA utility that lets you create a CD-ROM data base for quick access to CD-ROM data. main board: See motherboard.
- Page 173 Glossary modem: Derived from modulator/demodulator, a device that converts (modulates) digital data for transmission over telephone lines and then converts modulated data (demodulates) to digital format where received. monitor: A device that uses rows and columns of pixels to display alphanumeric characters or graphic images.
- Page 174 The electrical connection through which the computer sends and receives data to and from devices or other computers. Power Saver Utility: A TOSHIBA utility that lets you set the parameters for various power-saving functions. printed circuit board (PCB): A hardware component of a processor to which integrated circuits and other components are attached.
- Page 175 A Class A device is sufficient for office use. Class B provides a more stringent classification for home equipment use. TOSHIBA portable computers comply with Class B computing device regulations. RAMDRIVE: Part of the computer’s random access memory assigned to simulate a disk.
- Page 176 Glossary SCSI: Small Computer System Interface is an industry standard interface for connection of a variety of peripheral devices. SD cards: Secure Digital cards are flash memory widely used in a variety of digital devices such as digital cameras and Personal Digital Assistants.
- Page 177 TFT: Thin-film transistor. A colour LCD technology that applies individual transistors to each pixel enabling fine display control and excellent screen legibility. touch pad: A pointing device integrated into the TOSHIBA computer palm rest. TTL: Transistor-transistor logic. A logic circuit design that uses switching transistors for gates and storage.
-
Page 178: Index
4-7 replacing, 6-11 writing, 4-9 safety precautions, 6-5 computer types, 6-3 cleaning, 4-22 buttons moving, 4-22 CD/Digital, 4-8 restarting, 3-12 CD/DVD/Audio control buttons, Copyright, ii Internet, 2-9 Power, 2-8 TOSHIBA Console, 2-9 TV-Out, 1-6, 2-9 User's Manual Satellite P10 Series... - Page 179 Index DC IN hard disk drive indicator, 6-3 problems, 8-8 DC IN 19 V Jack, 2-6 Headphone Jack, 1-6, 2-3 Dimensions, 1-7 Hibernation Direct Play, 1-6 automatic, 6-13 Disclaimer, ii problems, 8-19 diskette Hyper-Threading Technology care, 4-12 problems, 8-5 diskette drive, 2-12 Diskette drive i.LINK, 7-13 problems, 8-13...
- Page 180 Index LAN, 1-7, 4-17 Panel power off/on, 6-13 Jack, 2-6 Parallel port, 1-5, 2-6 problems, 8-20 Parallel printer, 7-10 LCD panel PC Card, 1-5, 7-2 problems, 8-7 installing, 7-2 Lighting, 3-3 problems, 8-15 Line-In Jack, 1-6, 2-3 removing, 7-3 Slot, 2-4 ports memory, 1-3 DC IN 19 V, 2-6...
- Page 181 PC Card, 8-15 System Indicators, 2-1 Power, 8-5 preliminary checklist, 8-2 printer, 8-14 Television, 7-11 self test, 8-4 TOSHIBA Console Button, 2-9 Sound system, 8-15 Touch pad, 2-8 Standby, 8-19 Control Buttons, 2-8 support from TOSHIBA, 8-22 problems, 8-16 system start-up, 8-3...
- Page 182 Index Weight, 1-7 port, 1-5, 2-4, 2-5 Windows special keys, 5-5 problems, 8-18 Wireless communications, 2-3, USB mouse 4-18 problems, 8-17 Wireless LAN, 1-7 Utilities, 1-9 problems, 8-21 Socket, 2-7 Work habits, 3-4 Volume Control, 2-1 Satellite P10 Series...