Related Manuals for Cisco ATA188-I2
Summary of Contents for Cisco ATA188-I2
- Page 1 At A Glance Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Overview Installation Configuration...
- Page 2 This guide contains basic instructions for installing, testing, and operating your Cisco Analog Telephone Adaptor (Cisco ATA 186 or Cisco ATA 188). For configuration information for use by service providers and system administrators, refer to the Cisco ATA administrator’s guide for your particular signaling image protocol (SCCP, MGCP, H.323...
- Page 3 Cisco ATA 186 The Cisco ATA 186 connects one or two analog telephones to an IP-based telephony network. The hardware features include: • Function button • Two RJ-11 FXS ports • RJ-45 10BASE-T uplink port • Network activity (ACT) LED •...
- Page 4 Cisco ATA 188 The Cisco ATA 188 connects one or two analog telephones to an IP-based telephony network. The hardware features include: • Two RJ-11 FXS ports • RJ-45 10/100BASE-T uplink port • RJ-45 10/100BASE-T data port • Two link activity (LINK) LEDs •...
-
Page 5: Safety Recommendations
Safety Recommendations To ensure general safety, follow these guidelines: • Do not open or disassemble this product. • Do not get this product wet or pour liquids into this device. • Do not perform any action that creates a potential hazard to people or makes the equipment unsafe. - Page 6 voorkomen. Gebruik het nummer van de verklaring onderaan de waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt raadplegen. BEWAAR DEZE INSTRUCTIES Varoitus TÄRKEITÄ TURVALLISUUSOHJEITA Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu onnettomuuksien yleisiin ehkäisytapoihin.
- Page 7 und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden. BEWAHREN SIE DIESE HINWEISE GUT AUF. Avvertenza IMPORTANTI ISTRUZIONI SULLA SICUREZZA Questo simbolo di avvertenza indica un pericolo.
- Page 8 Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de prevenção de acidentes.
- Page 9 Warning Ultimate disposal of this product should be handled according to all national laws and regulations. Warning Read the installation instructions before you connect the system to its power source. Warning This equipment contains a ring signal generator (ringer), which is a source of hazardous voltage. Do not touch the RJ-11 (phone) port wires (conductors), the conductors of a cable connected to the RJ-11 port, or the associated circuit-board...
- Page 10 Warning To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some LAN and WAN ports both use RJ-45 connectors. Use caution when connecting cables.
-
Page 11: Installation Requirements
Installation Installation Requirements The analog telephone adaptor (ATA) package includes: • Cisco ATA 186 or Cisco ATA 188 Analog Telephone Adaptor • Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor At A Glance (this document) • Regulatory Compliance and Safety Information for the Cisco ATA 186 and Cisco ATA 188. - Page 12 For uplink connections, use a crossover Ethernet cable to connect the Cisco ATA to another Ethernet device (such as a router or PC) without using a hub. Otherwise, use straight-through Ethernet cables for both uplink and data port connections.
-
Page 13: Installation Steps
Installation Steps Figure 4 illustrates the cabling for the Cisco ATA 186. Figure 5 illustrates the cabling for the Cisco ATA 188. Before powering up the Cisco ATA, perform any Note necessary configuration tasks. Refer to the Cisco ATA administrator guide for your particular signaling image protocol (SCCP, MGCP, H.323 or SIP), available on the... -
Page 14: Power Outlet
Figure 4 Cabling the Cisco ATA 186 PHONE 1 PHONE 2 10BaseT Power outlet IP network Analog telephones (or fax) 5V power adaptor Power cord... -
Page 15: Power Cord
Figure 5 Cabling the Cisco ATA 188 PHONE 1 PHONE 2 LINK 10/100 PC 10/100 UPLINK LINK Power outlet IP network Analog telephones (or fax) 5V power adaptor Power cord... - Page 16 Connect one end of a telephone line cord to the Phone Step 2 1 input on the rear panel of the Cisco ATA. Connect the other end to an analog telephone set. If you are connecting a telephone set that was...
- Page 17 Phone 2 input port. If you are connecting only one telephone to the Note Cisco ATA, you must use the Phone 1 input port. Connect an Ethernet cable to the uplink RJ-45 Step 4 connector on the Cisco ATA. For the Cisco ATA 186, this is the 10BASE-T connector;...
- Page 18 (Cisco ATA 188 only—optional) Connect a Step 5 straight-through Ethernet cable from your PC to the 10/100 PC RJ-45 connector on the Cisco ATA. Connect the socket end of the power cord to the 5V DC Step 6 power adaptor.
-
Page 19: Power-Down Procedure
LED flashes to indicate network activity. This LED is labeled ACT on the rear panel of the Cisco ATA 186 and is labeled LINK on the rear panel of the Cisco ATA 188. Do not cover or block the air vents on either the Caution top or the bottom surface of the Cisco ATA. - Page 20 The unit provides the following connectors and indicators: • 5V power connector. • Two RJ-11 FXS (Foreign Exchange Station) ports—The Cisco ATA supports two independent RJ-11 telephone ports that can connect to any standard analog telephone device. Each port supports either voice calls or fax sessions,...
- Page 21 • Ethernet ports The Cisco ATA 186 has one RJ-45 10BASE-T uplink – Ethernet port to connect the Cisco ATA 186 to a 10/100BASE-T hub or another Ethernet device. The Cisco ATA 188 has two Ethernet ports: an RJ-45 –...
- Page 22 LED blinks to show network activity and is solid when there is a link. • The Cisco ATA 186 RJ-45 LED is solid when the Cisco ATA is powered on and blinks to show network activity. • Function button—The function button is located on the top...
- Page 23 A P T O R The function button lights when you pick up the handset of a telephone attached to the Cisco ATA. The button blinks quickly when the Cisco ATA is upgrading its configuration. If the function button blinks slowly, the Cisco ATA Note cannot find the DHCP server.
- Page 24 Cisco ATA. Configuration For complete configuration information, see the administrator’s guide for the signaling image protocol you are using (SCCP, MGCP, H.323 or SIP). The Cisco ATA administrator’s guides are located at the following URL: http://www.cisco.com/univercd/cc/td/doc/product/voice/ata/ata admn/index.htm...
-
Page 25: Making A Call
• Make sure that the DHCP server is operating correctly. Note that the function button blinks slowly when the Cisco ATA attempts to acquire the DHCP configuration. • If the green activity LED is not flashing after you connect the Ethernet cable, make sure that both the power cord and... - Page 26 • If there is no dial tone, make sure that the telephone line cord from the telephone is plugged into the appropriate port on the Cisco ATA. Make sure that your Cisco ATA is properly registered on your Call Control system. Test another phone;...
- Page 28 CCVP, the Cisco logo, and the Cisco Square Bridge logo are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn is a service mark of Cisco Systems, Inc.; and Access Registrar, Aironet, BPX, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, Cisco, the Cisco Certified...