Express Script Installer Menu Wizard - LG 323DCH - 32In Wide Lcd Hdtv Spk 1366X768 Hospital Grade Commercial Mode Setup Manual

Express Script Installer Menu Wizard

(LG3DDH TVs only)
The Express Script Installer Menu Wizard enables users to set up essential items for viewing the TV the
fi rst time it is turned On. The Express Script Installer Menu Wizard can also be activated from the Installer
Menu—set Installer Menu item 117 FACT DEFAULT to 001 to reinitiate the Express Script (see the
"Installer Menu" section of this document for further information).
Note: If you plan to perform the Commercial Mode Setup using the procedure on pages 14 to 15, via cloning,
or via the FTG (Free-To-Guest) Confi guration Application, be sure to exit the Express Script in order to avoid
setup confl icts that may cause the TV to malfunction.
Installer Menu Wizard
Select Menu Mode
Which menu mode will you be using?
Express Script
Exit Express Script
PTC: V1.00.004 CPU: V03.19.00 FPGA: 20E7
Installer Menu Wizard
Step 1. Tuning Band
Which tuning band would you like to use?
►
Cable Standard
Exit Script
F G
Back
PTC: V1.00.004 CPU: V03.19.00 FPGA: 20E7
Installer Menu Wizard
Step 2. Aux Input
Which inputs will you be using?
Customize Inputs.
Use default values.
Back
PTC: V1.00.004 CPU: V03.19.00 FPGA: 20E7
Installer Menu Wizard
Step 3. Pillow Speaker
Up/Down/Left/Right arrow keys
Which brand pillow speaker code will you be using?
►
Zenith code
Exit Script
F G
Back
PTC: V1.00.004 CPU: V03.19.00 FPGA: 20E7
16
1. Upon launching, the Installer Menu Wizard prompts you to select a
preferred Menu Mode. Use the Up/Down arrow keys on the Installer
Remote to select/highlight Express Script in order to proceed with the
Installer Menu Wizard. Then, press OK (Enter) on the Installer Remote.
The remaining steps of this procedure describe the Express Script
Installer Menu Wizard. Use the Installer Remote to make selections and
complete each step. You can select the Back button, where available, to
check previous settings, as necessary.
OK
Note: Select Exit Express Script and press OK (Enter) if you wish to
exit the Installer Menu Wizard.
1
► 2 ► 3 ► 4 ► 5 ► 6 ► 7
2. Use the Left/Right arrow keys to select the appropriate tuning band
(Cable Standard [default], Cable HRC, Cable IRC, or Air). When you
have made your selection, use the arrow keys to select Next, and then
►
press OK (Enter).
Next
OK Exit Express Script
3. Use the Up/Down arrow keys to select the desired Aux input option.
(Note: If you simply select Next and press OK (Enter) in this step, default
► 2 ► 3 ► 4 ► 5 ► 6 ► 7
1
values will be used.)
• To customize settings, select Customize Inputs and press OK (Enter).
Next
• To use default values, select Use default values and press OK (Enter).
OK Exit Express Script
1 ► 2 ► 3 ► 4 ► 5 ► 6 ► 7
4. If using a Zenith pillow speaker code (default), you can simply select
Next and press OK (Enter).
► Otherwise, select the pillow speaker code fi eld, and use the Left/Right
arrow keys to select the appropriate option. When you have made your
selection, use the arrow keys to select Next, and then press OK (Enter).
Next
OK Exit Express Script
Aux input options are displayed in a pop-up window. Use the arrow
keys to select the input(s) you want to enable or disable. When you are
fi nished, press MENU to close the pop-up window. Then, continue with
step 4.
Then, continue with step 4.
(Continued on next page)
206-4096