HP 201723-B21 - StorageWorks Modular SAN Array 1000 Hard Drive Quick Start Instructions page 7

The workaround is to manually mount the installation CD. For
example, if the CD was auto-mounted in /media/HpInstallx.x,
issue these commands to unmount and then re-mount the CD:
# unmount /media/HpInstallx.x
# mkdir -p /mnt/cdrom
# mount /dev/cdrom /mnt/cdrom
If the unmount command fails with a busy warning, make sure that
all applications and consoles that could be using the CD media are
closed, and then try again.
2. Change directory to the linux directory. For example, if the
installation CD is mounted in /mnt/cdrom, issue the following
command:
# cd /mnt/cdrom/HP_SSCM/linux/
3. Run the install_smb.sh script as follows:
# ./install_smb.sh
This will install the following components:
• QLogic FC HBA driver
• HP Array Configuration Utility
• QLogic SANsurfer agent, QLRemote (if possible, the
installation program will also start the SANsurfer agent,
QLRemote)
4. If the following message appears at the end of the installation,
you must restart the computer; otherwise, continue with
New driver and qlremote installed but not active.
For new driver and qlremote to be active either:
Reboot the system (Mandatory in case of Boot from
SAN)
or
Stop all the applications using QLogic driver.
Unload QLogic driver by executing following
command:
# modprobe -r qla2xxx (ex. qla2300, qla2400)
Reload new driver by executing following command:
# modprobe -v qla2xxx
Start qlremote as follows:
# /etc/init.d/qlremote start
Rebooting the system will automatically load new
driver and start qlremote.
5. The fabric device management interface (FDMI) enables the
management of devices such as HBAs through the fabric. To
install the Linux driver with FDMI enabled (by default, FDMI is
disabled), issue the following command:
# modprobe -v qla2xxx ql2xfdmienable=1
6. To verify that the installation is completed, check the FC HBA
driver version:
a. To ensure that the driver is installed in the correct location,
issue the following command:
# modinfo qla2xxx
The following is returned:
Filename: /lib/modules/ 2.6.18-8.ELsmp/kernel/
drivers/scsi/qla2xxx/qla2xxx.ko
Version: 8.02.03
b. To verify that the driver is loaded, issue the following
command:
# lsmod | grep qla2xxx
The following is returned:
qla2xxx_conf
qla2xxx
scsi_mod
c. To verify that the correct driver is loaded, issue the following
command:
# cat /proc/scsi/qla2xxx/* | grep "Driver version"
The following is returned:
Firmware version: 3.03.25 IPX
Driver version: 8.02.02-fop
Congratulations! You have successfully installed
your 8Gb Simple SAN Connection Kit hardware
and Simple SAN Connection Manager software.
Using Simple SAN Connection
Manager
To configure your storage system, use the Simple SAN Connection
Manager software. This software is installed on your server only if
you selected the Management Installation option in
step 6:
SAN Connection Manager
1. To launch the software, choose one of the following options:
• Click Start, point to All Programs > Hewlett-Packard > HP
StorageWorks Simple SAN Connection Manager, and then
click HP StorageWorks Simple SAN Connection Manager.
• Double-click the desktop shortcut:
If this is the first time you have launched this software for a new,
uninitialized EVA subsystem or an unconfigured MSA subsystem,
the installer prompts you to configure it. For details, refer to the
"Getting started" section of the HP StorageWorks Simple SAN
Connection Manager user guide, available online at
www.hp.com/go/8Gb-SSC.
2. Wait while the application discovers (detects) switches, servers,
storage subsystems, and logical disks. This may take a few
minutes.
If the application detects a new, unconfigured switch in your
SAN, the New Switch Setup dialog box
dialog box guides you through setting the switch IP address,
administrator password, and default zoning. For details, refer to
the "Getting started" section of the HP StorageWorks Simple
SAN Connection Manager user guide.
If the switch is already configured, the New Switch Setup does
not appear.
Page 7
303752 1
982688 0
445298 qla2xxx
installation, page 3.
(Figure
step 4 of Simple
14) opens. This