1. Manuals
  2. Brands
  3. Sharp Manuals
  4. Oven
  5. AX1200S - 22" SuperSteam Oven
  6. Installation instructions manual

Sharp AX1200S - 22" SuperSteam Oven Installation Instructions Manual

Built-in kit model
Hide thumbs Also See for AX1200S - 22" SuperSteam Oven:
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual See also: Operating Manual

INSTALLATION INSTRUCTIONS

IMPORTANT:
This Built-In Kit is designed for use with Sharp SuperSteam Ovens specifying a RK-12S30
Built-In Kit on the rating label on the front of the oven.
The cabinet or wall opening must be within the following dimensions:
HEIGHT
WIDTH
DEPTH
The completed built-in kit frame assembly dimensions:
HEIGHT
WIDTH
NOTE: The bottom of the cut-out opening for built-in use must be 36 inches (915 mm) or higher from the floor.
PLEASE READ THESE INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION!
The electrical requirements for this oven are 120 volts, 15 amps. The oven has a 5-15 plug
and requires a 5-15 receptacle.
PROVIDED PARTS
EXHAUST DUCT
EXHAUST
BACK
DUCT UPPER
DIVIDE PLATE L
EXHAUST DUCT BOTTOM
REAR SPACER
SCREW (A) - SHORT
SCREW (B) - MIDDLE
* For walls other than wood, you may need screws appropriate for that
wall to install the frame.
* Be sure to DISCONNECT THE PLUG of the oven from the electrical
outlet before installing the oven and kit.
* Because the kits are metal, due caution should be used in handling
and installation to avoid the possibility of injury.
BUILT-IN KIT MODEL
1
19" to 19
/
" (482 mm - 486 mm)
8
1
28" to 28
/
" (710 mm - 719 mm)
4
1
23
/
" minimum (509.5 mm minimum)
4
1
19
/
" (495mm)
2
30" (762mm)
RECTIFIER
PLATE L
EXHAUST
DIVIDE PLATE R
DUCT LEFT
FRAME
ASSEMBLY
SCREW (C) - LONG
1
RK-12S30
PART NAME
EXHAUST DUCT BACK
PDVC-B107WRWZ
EXHAUST DUCT UPPER
PDVC-B105WRWZ
DIVIDE PLATE L
PSKR-A486WRWZ
DIVIDE PLATE R
PSKR-A487WRWZ
RECTIFIER PLATE L
PSKR-A484WRWZ
EXHAUST DUCT LEFT
PDVC-B108WRWZ
EXHAUST DUCT RIGHT
PDUC-B117WRWZ
EXHAUST DUCT BOTTOM
PDVC-B106WRWZ
EXHAUST
FRAME ASSEMBLY
DUCT
FDEC-A004WRKZ
RIGHT
SCREW(A)
XHTS740P08000
SCREW(B)
XMMS841P13000
SCREW(C)
XMSS827P25000
REAR SPACER
PSPAFA003WRWZ
5
CUSHION 1
/
15 mm x 405 mm
PCUS-A245WRPZ
1
CUSHION 2
/
5 mm x 618 mm
PCUS-A247WRPZ
CUSHION 3 1
30 mm x 689 mm
PCUS-A249WRPZ
1
CUSHION 4
/
5 mm x 305 mm
PCUS-A251WRPZ
1
CUSHION 5
/
5 mm x 382 mm
PCUS-A253WRPZ
TINSEB184WRRZ-D92
Q'TY
1
1
1
1
1
1
1
1
1
23
2
4
1
" x 16",
8
2
3
" x 24
/
",
4
8
1
1
1
/
" x 27
/
",
8
8
1
" x 12",
4
1
" x 15",
4
1
Printed in Thailand

Advertisement

Table of Contents
loading

Related Manuals for Sharp AX1200S - 22" SuperSteam Oven

Summary of Contents for Sharp AX1200S - 22" SuperSteam Oven

  • Page 1: Installation Instructions

    BUILT-IN KIT MODEL IMPORTANT: This Built-In Kit is designed for use with Sharp SuperSteam Ovens specifying a RK-12S30 Built-In Kit on the rating label on the front of the oven. The cabinet or wall opening must be within the following dimensions: HEIGHT 19"...

  • Page 2: Exhaust Duct Upper

    PREPARATION Follow the directions from 1 to 5 to attach cushions to some parts. 1. EXHAUST DUCT UPPER Remove the backing paper from each CUSHION 1. Attach the CUSHIONS 1 to each side flange of the EXHAUST DUCT UPPER as shown in the illustration below.

  • Page 3: Exhaust Duct Bottom

    3. EXHAUST DUCT BOTTOM Remove the backing paper from CUSHION 3. Attach the CUSHION 3 to the EXHAUST DUCT BOTTOM as shown in the Illustration below. * Start A to attach the CUSHION 3. EXHAUST DUCT BOTTOM CUSHION 3 4. DIVIDE PLATE L Remove the backing paper from CUSHION 4.

  • Page 4: Electrical Supply

    STEP 1: CABINET OR WALL OPENING Provide an opening in the wall or cabinet shown in Figure 1. The depth should be minimum 23 " (590.5 mm). The floor of the opening should be constructed of plywood strong enough to support the weight of the oven (about 150 lbs., 68.1 kg) and should be level for proper operation of the oven.
  • Page 5 STEP 3: EXHAUST DUCT BOTTOM INSTALLATION 1 Place the oven onto the EXHAUST DUCT BOTTOM, lowering the 4 feet of the oven onto the projections at the 4 corners of EXHAUST DUCT BOTTOM as shown in Figure 3-A. Projection EXHAUST DUCT BOTTOM Figure 3-A Figure 3...
  • Page 6 STEP 5: INSTALLATION OF REAR SPACER and EXHAUST DUCT UPPER 1 Attach RECTIFIER PLATE L to inside of EXHAUST DUCT UPPER with 4 SCREWS (A) as shown in Figure 5-A. 2 Place EXHAUST DUCT UPPER over the oven and EXHAUST DUCT BACK, and attach REAR SPACER with 2 SCREWS (A) in Figure 5-B.

  • Page 7: Step 8: Oven Installation

    STEP 7: INSTALLATION OF EXHAUST DUCT RIGHT 1 Attach EXHAUST DUCT RIGHT to the right wall of the oven. 2 Tighten with 4 SCREWS (A) as shown in the Figure 7. EXHAUST DUCT UPPER SCREW (A) EXHAUST DUCT RIGHT SCREW (A) Figure 7 DIVIDE PLATE R STEP 8: OVEN INSTALLATION...
  • Page 8 Figure 9 FRAME ASSEMBLY Pull bottom panel of FRAME ASSEMBLY toward you to remove or replace the drip tray. For any other assistance or information about this product, please call SHARP's Customer Assistance Cen- ter 1-800-BE-SHARP. ® SHARP ELECTRONICS CORPORATION...

This manual is also suitable for:

Rk-12s30Ax-1200k

Table of Contents