Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing.
LSI MegaRAID Userʼs Manual About This Manual This manual is designed for users who have already acquired knowledge of peronal computer integration so as to help establish a powerful ASUS server. Overview The structure of this manual is listed as follows: 1.
Important: Important tips or things to be paid attention to. Note: Tips, definitions, or further explanations More Information about This Product You could get, via the following two media, information about the ASUS products you are using as well as the upgrade information for both software and hardware.
RAID Setup With step-by-step descriptions, this chapter introducess the procedures of setting up a RAID on your system at the time when system is powered on and not yet enters the operation system.
LSI MegaRAID Userʼs Manual 1.1 Change the Speed of SCSI Channel 1. Press Ctrl + H at the same time and enter the MegaRAID WebBIOS configuration window. Select with your mouse or keyboard the SCSI Channel Properties in the WebBIOS configuration menu. 2.
Page 9
LSI MegaRAID Userʼs Manual 3. Click on the arrow of SCSI Capabilities box and open the drop down menu. The four speed selections are Fast, Ultra, Ultra-II, U160, and U320. Select a suitable speed and click the Submit button to save the new configuration.
LSI MegaRAID Userʼs Manual 1.2 RAID 0 or RAID 1 Setup 1. Press at the same time Ctrl + H and enter the MegaRAID WebBIOS configuration window where information about all physical drivers installed is displayed. Click Configuration Wizard to start RAID setup.
Page 11
LSI MegaRAID Userʼs Manual 3. If the setting is to meet special requirements, please click on Custom Configuration. You could also let the Configuration Wizard to set up a RAID automatically by selecting Auto Configuration. Press Next to continue. 4. Press and hold on the Ctrl key on your keyboard and select two ready drives with your mouse, then click Accept Array to setup RAID 1.
Page 12
LSI MegaRAID Userʼs Manual 5. In the right side windows you could view the information of all RAIDs (arrays). Click Accept Array and Next to continue. 6. For RAID 0 configuration, set the RAID Level as RAID 0, and input the RAID 0 size value within the circled area into the Select Size box (For example: RAID 0 size= 70004 MB).
Page 13
LSI MegaRAID Userʼs Manual 7. For RAID 1 configuration, set the RAID Level as RAID 1, and input the RAID 1 size value within the circled area into the Select Size box (For example: RAID 1 size= 35002 MB). Then click Accept and Next to continue.
Page 14
LSI MegaRAID Userʼs Manual 9. Click Yes to save the setup. 10. Click Yes to initialize the new logical drives.
Page 15
LSI MegaRAID Userʼs Manual 11. If no boot device is ever set, please select Set Boot Drive and then select Go to change the settings so that the RAID storage devices could become the first boot device.
LSI MegaRAID Userʼs Manual 1.3 RAID 5 Setup 1. Press at the same time Ctrl + H and enter the MegaRAID WebBIOS configuration window where information about all physical drivers installed is displayed. Click Configuration Wizard to start the RAID settings.
Page 17
LSI MegaRAID Userʼs Manual 3. If the setting is to meet individual requirements, please select Custom Configuration. You could also let the Configuration Wizard set up a RAID automatically by selecting Auto Configuration. Click Next to continue. 4. Hold on the Ctrl key on your keyboard and select with your mouse five ready drives, then click on Accept Array to setup Array 1.
Page 18
LSI MegaRAID Userʼs Manual 5. This warning window will prompt out when hard disks of different sizes are deployed in a RAID. If hard disks of identical space are used, this window would not appear. (We recommend using hard disks of a same model for RAID configurationn) 6.
Page 19
LSI MegaRAID Userʼs Manual 7. Set RAID Level as RAID 5 and input the Select Size box with the RAID 5 size value within the circled area. 8. You could see information of all RAID settings in the left side window. Click Accept to continue.
Page 20
LSI MegaRAID Userʼs Manual 9. Click Yes to save the configuration, or click No to cancel the settings. 10. Click Yes to initialize the new logical drives. 1-13...
Page 21
LSI MegaRAID Userʼs Manual 11. If no boot device is ever set, please select Set Boot Drive and then click Go to change the settings so that the RAID storage device could become the first boot device. 1-14...
LSI MegaRAID Userʼs Manual 1.4 RAID 50 Setup 1. Press at the same time Ctrl + H and enter the MegaRAID WebBIOS configuration window where information about all physical drivers installed is displayed. Click Configuration Wizard to start the RAID settings.
Page 23
LSI MegaRAID Userʼs Manual 3. If the setting is to meet individual requirements, please select Custom Configuration. You could also let the Configuration Wizard to set up a RAID automatically by selecting Auto Configuration. Then press Next to continue. 4. Hold on the Ctrl key on your keyboard and select with your mouse three ready drives, then click on Accept Array to setup RAID 50.
Page 24
LSI MegaRAID Userʼs Manual 5. The three disks are now set as Array 1. Click Accept Array to continue. 6. Then set the rest three hard disks as Array 2 and click Accept Array. Press Next to continue. 1-17...
Page 25
LSI MegaRAID Userʼs Manual 7. Select Array 1 and set the RAID Level as RAID5 and Span as Enabled. Then input the RAID 5 size value with spanning in the circled area into the Select Size box. Click Accept to continue. 8.
Page 26
LSI MegaRAID Userʼs Manual 9. Click Yes to save the configuration. 10. Click Yes to initialize the new logical drives. 1-19...
Page 27
LSI MegaRAID Userʼs Manual 11. If no boot storage device is ever set, please select Set Boot Drive and then select Go to change the settings so that the RAID storage device could become the first boot device. 12. Now you could see information about all physical drives and logical drives in the home page of WebBIOS.
LSI MegaRAID Userʼs Manual 1.5 RAID 10 Setup 1. Press Ctrl + H at the same time and enter the MegaRAID WebBIOS configuration window, where information about all physical drivers installed is displayed. Click Configuration Wizard to start the RAID settings.
Page 29
LSI MegaRAID Userʼs Manual 3. If the setting is to meet individual requirements, please select Custom Configuration. You could also let the Configuration Wizard set up a RAID automatically by selecting Auto Configuration. Click Next to continue. 4. Hold on the Ctrl key of your keyboard and select with your mouse two ready drives, click on Accept Array to set up Array 1 as RAID 0.
Page 30
LSI MegaRAID Userʼs Manual 5. Select two hard disks as and set them as Array1, and the rest Array 2. At least two hard disks are needed for setting up RAID 1, and the number of disks must be even. 6.
Page 31
LSI MegaRAID Userʼs Manual 7. You could now see information of all RAID settings. When you have finished the setting for Array 1 and Array 2, please click Next to continue. 8. Set Array 1 as RAID 1, and set the Span as Enable. Input the Select Size box with the RAID 1 size value within the circled area;...
Page 32
LSI MegaRAID Userʼs Manual 9. You could then see the information of RAID settings in the Configuration Preview window. The two arrays form a RAID 10, with the Array 2 being the continuance of the Array 1. 10. Click Yes to save the settings, or to click No to cancel the configuration. 1-25...
Page 33
LSI MegaRAID Userʼs Manual 11. Click Yes to initialize the new array of Logical Drives. 12. If no boot device is ever set, please select Set Boot Drive and then select Go to change the settings so that the RAID storage device could become the first boot device.
Page 34
LSI MegaRAID Userʼs Manual 1.6 Array Rebuild 1. When one of the hard disks within the array is removed and substituted with new disk, the array could automatically start the rebuilding process. You could check the information of the rebuilding progress in the MegaRAID WebBIOS configuration window.
LSI MegaRAID Userʼs Manual 1.7 Migration Setup 1. If new hard disks are to be installed onto the SCSI backplane, please select Scan Devices to discover the disk first. Then you will find the ready disk in the Physical Drives window. Click on Logical Drives to set up Migration.
LSI MegaRAID Userʼs Manual 1.8 Hotspare Setup 1. Select a ready physical drive and set it as Hotspare. Note: The disks already set as a part of RAID (Online) could not be selected. 2. Select Make Hotspare and click Go to set this hard disk as Hotspare. 1-29...
Page 37
LSI MegaRAID Userʼs Manual 3. If it is to stop the Hotspare function, select Offline and click Go to cancel. 4. The hard disk assigned as Hotspare will be highlighted in pink characters, which means the Hotspare setting is completed. 1-30...
Page 38
LSI MegaRAID Userʼs Manual 1.9 Clear Arrays 1. Press Ctrl + H at the same time and enter the MegaRAID WebBIOS configuration window, where information about all physical drivers installed is displayed. Click Configuration Wizard to start the setup. 2. Select Clear Configuration tab, and then click Next. 1-31...
Page 39
LSI MegaRAID Userʼs Manual 3. You could find no Logical Drivers in the right side window, which means the disk arrays have already been cleared. Click Accept to continue. 4. Click Yes and save the configuration. 1-32...
Page 40
LSI MegaRAID Userʼs Manual 5. In the right side windows, all the storage devices are listed in the Physical Drives window, while the Logical Drives window is blank. 1-33...
System Setup This chapter will guide you throught the relevant settings after entering the operation systems.
Page 43
2.1.1 Microsoft® Windows® Insert the support CD with the label reading LSI MegaRAID SCSI 320- 0/320-1 320 & ASUS AZ CRB into your optical drive and open the Driver folder. There are, in this folder, drivers for all operating systems for creating a installation floppy disk.
Page 44
LSI MegaRAID Userʼs Manual 2. When a screen as follows prompts out, press S to install driver for the operation system. 3. Insert the drive disk previously prepared into the floppy drive, and press Enter.
Page 45
LSI MegaRAID Userʼs Manual 4. For Windows 2000®, please select LSI MAGARAID Product for Windows 2000 Driver; For Windows 2003®, please select LSI MEGARAID Products for Windows 2003 (x86). 5. For Windows 2003 Server®, when driver program is selected, a following window would prompt out, displayig the detected preset driver of Windows 2003 Server®.
Page 46
LSI MegaRAID Userʼs Manual 2.1.2 RedHat Linux® You could get access ASUS global website to download the *.zip driver. Unzip the file in Windows® OS and run the *.exe file, the driver would automatically write into the floopy disk. If the unzipped files are not *.exe file, please copy these files directly into a blank disk.
Page 47
LSI MegaRAID Userʼs Manual 3. Insert the drive disk into the floopy drive, and follow the instruction to proceed with the installation. Press Yes, and then press Enter. 4. Select fd0 to install from floopy drive. Select OK and press Enter. If a USB floopy drive is deployed, please select sda to install from the floopy disk.
Page 48
LSI MegaRAID Userʼs Manual 5. The operating system now is reading from the drive disk in the floopy drive. 6. When the installation is completed, please select No and press Enter to enter the Linux® OS; if more drivers are to be installed, please select Yes and press Enter, then repeat the step 3-4 to proceed with the installation.
® Windows Server 2003 RedHat Linux SuSE Linux ® ® ® Operating System 2.1.1 Windows LSI MegaRAID SCSI 320-0/320-1 320 & ASUS AZ CRB Driver Windows SCSI RAID Driver\Windows\ Windows Windows 2000 Windows 2000 MakeDisk.exe Windows 2003 win2003 32bit 64bit MakeDisk.exe...
Page 91
LSI MEGARAID Products for Windows 2000 Driver Windows 2003 Server LSI MEGARAID Products for Windows 2003 (x86) Windows XP RAID 320-0 AZCRB [MegaRAID SCSI 320-0 controller] RAID 320-1 [MegaRAID SCSI 320-1 RAID controller] RAID 320-2 [MegaRAID SCSI 320- 2 RAID controller] LSI MegaRAID...
2.1.2 Red Hat Linux [LSI MegaRAID] Driver Red Hat SuSe 9.0 SCSI RAID \Driver\Linux\Redhat\2.10.8\Linux_2.10.8.2-1\Redhat and SuSe 9.0\Drivers\ megaraid2-v2.10.8.2-rhl90-kernels.img Red Hat 9.0 *.zip Windows *.exe MakeDisk.exe Linux linux Enter LSI MegaRAID...