Using In A Wall-Mounted State - Panasonic MW20 - DIGITAL PHOTO FRAME Operating Instructions Manual

Using in a wall-mounted state

The specifi c setting is required to use the main unit in a
wall-mounted state. Make the wall-mount settings on the
menu and install it on the wall.
Make sure to ask a professional mounter or a dealer
for installation/uninstallation.
Notes for installation
Do not install this unit at the following locations to ensure
this unit's performance and to prevent potential troubles.
– Locations other than vertical walls
– Locations near a sprinkler or a sensor
– Locations near high-voltage lines or power sources
– Locations where wind from a heating device hits the unit
– Locations where the unit is subject to vibration or
impact
– Locations near sources of magnetism, heat, vapor, oil
smoke, etc.
– Locations of high temperature, such as near ceiling
lights (spotlight, halogen light, etc.)
– Locations where there may be water droplet (i.e. under
an air conditioner)
– High places where the SD insertion part cannot be
reached easily
Use a proper installation method that suits the structure
and material of the installing location.
Use a cloth, etc. to prevent damage of the product or
fl oor during installation.
When tightening screws, make sure the screws are not
loosely-tightened or overtightened.
Secure safety in the surrounding areas and pay enough
attention during installation.
Prepare commercially available screws that match the screw
holes of the unit's bottom face.
Screw hole on the main
unit's bottom face
5 mm (13/64")
11 mm (7/16")
Recommended type of screw
• 2 screws for wall-mounting
• 2 screws for the fi tting for wall-mounting
A length which supports the strength of 5 kg (11.1 lb.) or
more must be kept for each screw.
At least 30 mm (1
7.4 mm (19/64") to 9.4 mm (3/8")
4 mm
2.2 mm (3/32") to 3 mm (1/8")
(5/32")
3 mm (1/8") to 4 mm (5/32")
Use commercially available screws with the nominal
diameter of 4 mm (5/32") or equivalent which are suitable for
materials of the wall (i.e. wood, steel, concrete, etc.)
Note
• Panasonic is not liable for incidental or consequential
damages resulting from improper installation or operation.
• Keep the screws out of reach of children to prevent swallowing.
Wall-mount settings
1. Press [MENU].
2. Press [e, r, w, q] to select "Settings Menu" and
3. Press [e, r, w, q] to select "Wall-mount Setting"
4. Press [e, r] to select "Yes" and press [OK].
5. Press [w, q] to select "Yes" and press [OK].
Note
• The audio will be stopped (paused) automatically, during
playback.
The following buttons and functions that can be used will be
restricted.
Unusable buttons on
the main unit
Unusable buttons on
the remote control
Timer audio playback
function
Menu items
3
/ ")
16
Panasonic Logo
Power Save Setting
iPod/iPhone
connection
USB connection
press [OK].
and press [OK].
Wall-mount Setting
Yes
No
Selecting "Yes" will rotate the display by 180 degrees.
The main unit controls cannot be used in this mode.
Select Item OK
The power will be turned off and on automatically.
When the power is turned on, the main unit's screen
display is turned upside down.
When using with the wall-mount setting
Except [POWER 8]
• [iPod/PLAY MENU]
• [iPod/DISPLAY]
• [iPod/q/h]
Automatically disabled (with the
setting contents preserved)
• "iPod Play/Pause"
• "iPod Display"
• "iPod Play Menu"
• "Audio Menu"
• "Sync Music" in the "Photo
Playback Settings"
Automatically turned off
Automatically disabled
Cannot be used
Cannot be used
23