Page 1
Projector CP-WX3011N User's Manual (detailed) Operating Guide – Technical Example of computer signal Resolution (H x V) H. frequency (kHz) V. frequency (Hz) Rating Signal mode 720 x 400 37.9 85.0 VESA TEXT 640 x 480 31.5 59.9 VESA VGA (60Hz) 640 x 480 37.9...
Page 2
Initial set signals Initial set signals The following signals are used for the initial settings. The signal timing of some computer models may be different. In such case, adjust the items V POSITION and H POSITION in the IMAGE menu. Back porch (B) Front porch (D) Back porch (b)
Page 3
Connection to the ports Connection to the ports NOTICE ►Use the cables with straight plugs, not L-shaped ones, as the NOTICE ►Use the cables with straight plugs, not L-shaped ones, as the input ports of the projector are recessed. input ports of the projector are recessed. ►Only the signal that is input from the COMPUTER IN1 or IN2 can be output from the MONITOR OUT port.
Page 4
Connection to the ports (continued) HDMI TYPE A TYPE B DC5V 0.5A COMPONENT Cb/Pb Cr/Pr RCA jack x3 • System: 480i@60, 480p@60, 576i@50, 720p@50/60, 1080i@50/60, 1080p@50/60 Port Signal Component video Y, 1.0±0.1Vp-p with composite sync, 75Ω terminator Cb/Pb Component video Cb/Pb, 0.7±0.1Vp-p, 75Ω terminator Cr/Pr Component video Cr/Pr, 0.7±0.1Vp-p, 75Ω...
Connection to the ports (continued) HDMI TYPE A TYPE B DC5V 0.5A HDMI 10 12 14 • Type :Digital audio/video connector 13 15 • Audio signal : Linear PCM (Sampling rate; 32/44.1/48 kHz) Signal Signal Signal T.M.D.S. Data2 + T.M.D.S. Data0 Shield 15 SCL T.M.D.S.
Page 6
Connection to the ports (continued) HDMI TYPE A TYPE B DC5V 0.5A USB TYPE A USB TYPE B USB A type jack USB B type jack Signal Signal - Data - Data + Data + Data Ground Ground CONTROL D-sub 9pin plug •...
Connection to the ports (continued) To input component video signal to COMPUTER IN ports D-sub plug RCA plugs HDMI TYPE A TYPE B RCA connectors DC5V 0.5A COMPONENT VIDEO OUT VCR/DVD/ Blu-ray Disc™ player To input component video signal to the COMPUTER IN1 or IN2 port of the projector, use a RCA to D-sub cable or adapter.
Page 8
RS-232C Communication RS-232C Communication When the projector connects to the computer by RS-232C communication, the projector can be controlled with RS-232C commands from the computer. For details of RS-232C commands, refer to RS-232C Communication / Network command table ( Connection Turn off the projector and the computer.
Page 9
RS-232C Communication (continued) Communicaion settings 1. Protocol 19200bps,8N1 2. Command format ("h" shows hexadecimal) Byte Number Command Header Data Header Data Setting Action Type code size flag code Packet Action <SET>Change setting to desired value [(cL)(cH)] (aL) (aH) 01h 00h (bL) (bH) (cL) (cH) by [(eL)(eH)].
Page 10
RS-232C Communication (continued) 3. Response code / Error code ("h" shows hexadecimal) (1) ACK reply : 06h When the projector receives the Set, Increment, Decrement or Execute command correctly, the projector changes the setting data for the specified item by [Type], and it returns the code. (2) NAK reply : 15h When the projector cannot understand the received command, the projector returns the error code.
Command Control via the Network Command Control via the Network When the projector connects network, the projector can be controlled with RS- 232C commands from the computer with web browser. For details of RS-232C commands, refer to RS-232C Communication / Network command table ( Connection Turn off the projector and the computer.
Page 12
Command Control via the Network (continued) Communicaion Port The following two ports are assigned for the command control. TCP #23 TCP #9715 Configure the following items form a web browser when command control is used. Port Settings Click the [Enable] check box to open [Network Port open Control Port1 (Port: 23)] to use TCP #23.
Command Control via the Network (continued) Command control settings [TCP #23] 1. Command format Same as RS-232C communication, refer to RS-232C Communicaton command format. 2. Response code / Error code ("h" shows hexadecimal) Four of the response / error code used for TCP#23 are the same as RS-232C Communication (1)~(4).
Command Control via the Network (continued) 2. Response code / Error code ("h" shows hexadecimal) The connection ID is attached for the TCP#23's response / error codes are used. The connection ID is same as the sending command format. (××h : connection ID) (1) ACK reply : 06h + ××h (2) NAK reply : 15h + ××h (3) Error reply : 1Ch + 0000h + ××h...
Page 15
Network Bridge Communication Network Bridge Communication This projector is equipped with NETWORK BRIDGE function. When the projector connects to the computer by LAN communicaton, an external device that is connected with this projector by RS-232C communication can be controlled from the computer as a network terminal. For details, see the 3.7 Controlling the external device via the projector(using the NETWORK BRIDGE function) - Network Guide.
Network Bridge Communication Communication settings For communication setting, use the OPTION - SERVICE - COMMUNICATION menu. ( OPTION menu - SERVICE - COMMUNICATION in the User's Manual - Operating Guide) Item Condition BAUD RATE 4800bps / 9600bps / 19200bps / 38400bps Data length 8 bit (fixed) PARITY...
Page 17
RS-232C Communication / Network command table RS-232C Communication / Network command table Command Data Names Operation Type Header Action Type Setting code Turn off BE EF 06 00 2A D3 01 00 00 60 00 00 Turn on BE EF 06 00 BA D2 01 00...
Page 18
RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code CONTRAST Execute BE EF 06 00 A4 D2 06 00 01 70 00 00 Reset 1 DEFAULT BE EF 06 00 07 E9 01 00 A1 30 20 00...
Page 19
RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code BE EF 06 00 80 FE 02 00 96 30 00 00 User Gamma Increment BE EF 06 00 E6 FE 04 00 96 30 00 00 Point 7...
Page 20
RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code BE EF 06 00 BC F4 02 00 B7 30 00 00 COLOR TEMP Increment BE EF 06 00 DA F4 04 00 B7 30 00 00 OFFSET B...
Page 21
RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code BE EF 06 00 F1 82 02 00 01 21 00 00 H POSITION Increment BE EF 06 00 97 82 04 00 01 21 00 00 Decrement...
Page 22
RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code AUTO BE EF 06 00 BA 77 01 00 13 22 00 00 VIDEO BE EF 06 00 2A 76 01 00 13 22 01 00 HDMI FORMAT COMPUTER...
Page 23
RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code COMPUTER IN1 BE EF 06 00 F2 F4 01 00 B5 20 00 00 COMPUTER IN2 BE EF 06 00 32 F6 01 00 B5 20 04 00 MONITOR OUT...
Page 24
RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code BE EF 06 00 E9 CE 02 00 6B 20 00 00 VOLUME - LAN Increment BE EF 06 00 8F CE 04 00 6B 20 00 00 Decrement...
Page 25
RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code AUDIO IN1 BE EF 06 00 A2 DC 01 00 35 20 01 00 AUDIO IN2 BE EF 06 00 52 DC 01 00 35 20 02 00 AUDIO...
Page 26
RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code POLSKI BE EF 06 00 97 D7 01 00 05 30 0E 00 TÜRKÇE BE EF 06 00 07 D6 01 00 05 30 0F 00 DANSK BE EF...
Page 27
RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code TEST PATTERN BE EF 06 00 43 D9 01 00 22 30 00 00 DOT-LINE1 BE EF 06 00 D3 D8 01 00 22 30 01 00 DOT-LINE2...
Page 28
RS-232C Communication / Network command table (continued) RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code COMPUTER IN1 BE EF 06 00 3A 33 01 00 00 36 00 00 COMPUTER IN2 BE EF 06 00 FA 31...
Page 29
RS-232C Communication / Network command table (continued) RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code COMPUTER IN1 BE EF 06 00 FA 38 01 00 20 36 00 00 COMPUTER IN2 BE EF 06 00 3A 3A...
PJLink command PJLink command Commands Control Description Parameter or Response 0 = Standby POWR Power Contorol 1 = Power On 0 = Standby POWR ? Power Status inquiry 1 = Power On 2 = Cool Down 11 = COMPUTER IN 1 12 = COMPUTER IN 2 21 = COMPONENT 22 = S-VIDEO...
Page 31
NAME" of "NETWORK" Manufucturer's Name INF1 ? HITACHI inquiry INF2 ? Model Name inquiry CP-WX3011N Responds with the factory information and so INFO ? Other Information inquiry CLSS ? Class Information inquiry 1 NOTE • The password used in PJLink is the same as the password set in the Web Brouwser Comtrol.